Configurazione bl touch antclabs

droftarts

@perfetto said in Configurazione bl touch antclabs:

DWC 2.0.4
FIRMWARE 3.0

Okay, that's fine. You need to upload "Duet2CombinedIAP.bin" from https://github.com/Duet3D/RepRapFirmware/releases/tag/3.0 to the /sys folder on the SD card.

I suggest you update to 3.5.4, and we'll fix the configuration there. Download "Duet2and3Firmware-3.5.4.zip" from https://github.com/Duet3D/RepRapFirmware/releases/tag/3.5.4 and upload the whole zip file (don't unzip it) to the Duet in DWC.

Then send M122 again, to check it is updated.

Ian

perfetto

Ho caricato il file IAP nella cartella sys siè ricaricato il firmware 2.05.1 nei file di configurazione escono codici incomprensibili allego m122
m 122 -.txt

in seguito al tuo consiglio ho lanciato il firmware 3.5.4 adesso non si collega al web control dice versione incompatibile

droftarts

@perfetto said in Configurazione bl touch antclabs:

I uploaded the IAP file in the sys folder, the firmware 2.05.1 was reloaded, incomprehensible codes come out in the configuration files, I attach m122

"incomprehensible codes come out in the configuration files"? Please give me an example.

following your advice I launched the firmware 3.5.4, now it does not connect to the web control, it says incompatible version

When you upgrade, you MUST go from 2.05.1 to 3.0 first. You can go from 3.0 to 3.5.4. But you cannot go from 2.05.1 to 3.5.4. I assumed you were on 3.0, and would update to 3.5.4.

Most likely, the firmware is still 2.05.1, but DWC is 3.5.4. So you need to go back to DWC 2.0.4. Download "DuetWebControl-SD-2.04.zip" from https://github.com/Duet3D/RepRapFirmware/releases/tag/3.0 and unzip. Replace the contents of the www folder on the SD card with the files and folders from the zip.

I suggest you pick a firmware version, either 2.05.1 or 3.5.4, and stick to it. I recommend 3.5.4. We can fix configuration errors.

Ian

perfetto

@droftarts Ho ricominciato da zero:
caricato la prima configurazione funzionante del 2020
sono passato al firmware 2.05.1 poi alla 3.0 poi alla 3.5.4

attualmente in web control, impostazioni generali mi ritrovo:
Duet 2 2Ethernet versione 3.5.4
Duet Web Control DWC 3.5.4

allego m122 e config.g

m122.txt

config.g.txt

Spero di aver fatto bene

Grazie

droftarts

@perfetto said in Configurazione bl touch antclabs:

I started from scratch:
loaded the first working configuration of 2020
I switched to firmware 2.05.1 then to 3.0 then to 3.5.4

currently in web control, general settings I find myself:
Duet 2 2Ethernet version 3.5.4
Duet Web Control DWC 3.5.4

Okay, great! Currently, your configuration is for firmware 2.05.1. We need to update this for v3.x.

From your post here https://forum.duet3d.com/post/354792, you had a configuration for 3.5.1 (versione 3.5.1.txt). This is close to the configuration you need. If you have the configtool.json file for this (created by the configuration tool), can you upload it please? I can adjust it for you to match your original RRF v2.x configuration.

Ian

perfetto

credo sia questo, ormi ho un milione di cartelle di prova ma questo è il primo

configtool.json

grazie

perfetto

allego anche questo che fa parte della stessa conficonfig --.txt gurazione

droftarts

@perfetto said in Configurazione bl touch antclabs:

I think this is it, now I have a million test folders but this is the first
I also attach this which is part of the same configuration config.txt

This configuration is a little different, but no problem, I'll check it through. I've run out of time today, so will do this tomorrow morning.

Ian

perfetto

@droftarts grazie solo una cosa la home deve essere x0 y-5
ancora tanti grazie

perfetto

@perfetto
Buongiorno, ho provato a settare la macchina con il configuratore 3.5 ho caricato il file zippato tramite interfaccia web, il bl touch funziona le temperature vengono gestite, la macchina non esegue la home.
Nei file system ci sono molte cose strane ti ivio i file

M122.txt

config.g.txt

config. json vecchio.txt

configtool (1).json

grazie

droftarts

@perfetto said in Configurazione bl touch antclabs:

just one thing the home must be x0 y-5

Here is an updated configuration: perfetto config.zip.txt
Download this, delete the ".txt" from the end, and unzip the .zip file. (The forum does not allow .zip files to be uploaded.)

I recommend you rename the existing 'sys' folder on the SD card to 'sys_old', and copy the contents of the .zip file above to a new 'sys' folder on the SD card.

The config.g is quite similar to your "versione 3.5.1.txt", but I have changed a lot of the values so they are the same as your "config.g funzionante 2020.txt". See the differences here: https://www.diffchecker.com/gZTQOoak/

After you restart the Duet, please follow the 'Commissioning' guide, to check everything is working, here: https://docs.duet3d.com/en/How_to_guides/Commissioning
If anything is not working, let me know. Provide as much detail as possible.

Ian

droftarts

@perfetto said in Configurazione bl touch antclabs:

Good morning, I tried to set up the machine with the configurator 3.5 I uploaded the zipped file via web interface, the bl touch works the temperatures are managed, the machine does not run the home.
In the file systems there are many strange things I send you the files

Please see my post above. If there are problems, please explain each one clearly.

Ian