Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Black printbite and IR Sensor - very inconsistent heights?

    Scheduled Pinned Locked Moved
    IR Height Sensor
    10
    30
    4.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • RGN01undefined
      RGN01
      last edited by

      Thanks, swoozle, but that seems to be related to the clear / white PrintBite as it talks about grid lines. The black that I have does not have those lines. I'm thinking of changing to an inductive sensor if I can't get this right.

      I'd use the piezo but I don't know how I'd connect it to my x-carriage or bed - neither was designed for that.

      Richard

      1 Reply Last reply Reply Quote 0
      • Dougal1957undefined
        Dougal1957
        last edited by

        can you lower your IR Sensor by about 1 mm in relation to the nozzle?

        I think the recommended distance is between 1 and 2 mm but it is a while since I used one

        1 Reply Last reply Reply Quote 0
        • RGN01undefined
          RGN01
          last edited by

          Yes, I could try that but I don't have much height to play with. The dimension I quoted to David is the height of the bottom of the sensor board above the PrintBite when the sensor triggers - 3.3mm approximately. At that point the nozzle is 2.26mm above the PrintBite so the height difference is close to the recommended 1.5mm - actually a bit lower than recommended but it never fouled a print on the previous print surface (PEI on a black PCB heatbed).

          Now that I've made the change to aluminium plate and added the PrintBite I'm beginning to wonder if that inductive proximity sensor isn't my best bet. Either that or a BL Touch, perhaps.

          Richard

          1 Reply Last reply Reply Quote 0
          • RGN01undefined
            RGN01
            last edited by

            I've just used Blu-Tack to mount an inductive sensor under my carriage and tested that manually by monitoring the LED on it as I lowered the nozzle. Even like that it is repeatable to less than 0.01mm and the peaks and valleys seem to have gone.

            I just need to figure out how to wire it up (I'm already using an NPN inductive sensor on Z-max as my Z-home and only want this one for Z-probe, not homing.

            Richard

            1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators
              last edited by

              I'll ask Jason again for a sample of matt black PrintBite to test the IR sensor with.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • RGN01undefined
                RGN01
                last edited by

                Thanks, David.

                It does seem to be something to do with the interaction between the PrintBite and the IR sensor. I'm busy printing a mount for the inductive sensor and will try that later.

                Is it possible to connect the NPN inductive sensor yo the Z-probe input of the Duet WiFi through a Schottky diode? Is it the Z-Probe_In pin that I connect to the diode and the sensor and then just set it as a switch input?

                Thanks.

                Richard

                1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by

                  @RGN01:

                  Is it possible to connect the NPN inductive sensor yo the Z-probe input of the Duet WiFi through a Schottky diode? Is it the Z-Probe_In pin that I connect to the diode and the sensor and then just set it as a switch input?

                  Yes, see the wiki. If you use the Z probe input then an ordinary small signal silicon diode will probably work too if you don't have a Schottky one.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • Mutleyundefined
                    Mutley
                    last edited by

                    Hi Richard, Generally it has been positive feedback with the IR sensor on the black (matte) PB. Dave will have some to test early in the week. Possibly a silly question but any surface imperfections or scratches on the PB that might be distorting the readings?
                    J

                    1 Reply Last reply Reply Quote 0
                    • RGN01undefined
                      RGN01
                      last edited by

                      Thanks, I found the new one (the format is growing on me) and got it sorted. The applicable lines in config.g are as follows:

                      [c]; IR Z-probe
                      M558 P1 H4 F250 T2000 ; Set Z probe type to unmodulated and the dive height + speeds
                      G31 P500 X9 Y21 Z2.26 ; Set Z probe trigger value, offset and trigger height

                      ; Inductive Sensor
                      M558 I1 P5 H4 F250 T2000 ; Set Z probe type to digital and the dive height + speeds (I1 = invert signal)
                      G31 X9 Y21 Z2.26 ; Set Z probe trigger value, offset and trigger height
                      [/c]

                      I'm constantly amazed at the ease of changing things with the Duet!

                      Richard

                      (edited to fix typos)

                      1 Reply Last reply Reply Quote 0
                      • dc42undefined
                        dc42 administrators
                        last edited by

                        @RGN01:

                        T
                        I'm constantly amazed at the ease of changing things with the Duet!

                        "One firmware binary to rule them all" (all Duets that is) - with apologies to JRR Tolkien.

                        Seriously, we want you to be able to change ANYTHING that isn't a 1-off requirement by sending the appropriate GCode, either in config.g or live from DWC or USB. I even have a macro for homing my Cartesian printer and then turning it into a pretend CoreXY printer for firmware testing.

                        In the unlikely event that your requirement is a 1-off (e.g. the user who recently needed to add a 13th stepper driver), RepRapFirmware is open source so you have the freedom to modify it - and it will stay that way.

                        Duet WiFi hardware designer and firmware engineer
                        Please do not ask me for Duet support via PM or email, use the forum
                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                        1 Reply Last reply Reply Quote 0
                        • RGN01undefined
                          RGN01
                          last edited by

                          To close this out - I'm now using a TL-W5MC1 inductive proximity sensor and am getting repeatability of about 0.002mm and the PrintBite is showing as flat to all intents and purposes.

                          I'm adjusting a few things to now get it level but one step closer and that sensor works well - especially at the price! https://www.ebay.co.uk/itm/5mm-Noncontact-Inductive-Proximity-Sensor-Switch-Detect-DC-6-36V-NPN-TL-W5MC1-/253114333447

                          Richard

                          1 Reply Last reply Reply Quote 0
                          • rkrammesundefined
                            rkrammes
                            last edited by

                            My results with the matt white Printbite+ with a grid. 😞 I purchased my sensor more than a year ago and it is not a surface mount board. Would it be worthwhile to put some electrical tape in the corners and define points there for probing? I really like both this sensor and Printbite but if one has to go unfortunately it will be the sensor.

                            1 Reply Last reply Reply Quote 0
                            • GeckoBox3Dundefined
                              GeckoBox3D
                              last edited by

                              @dc42:

                              I'll ask Jason again for a sample of matt black PrintBite to test the IR sensor with.

                              Any update on this? I've been waiting to see someone's results for a while as my old gridded printbite gives horrendous IR probe results

                              1 Reply Last reply Reply Quote 0
                              • dc42undefined
                                dc42 administrators
                                last edited by

                                I've just chased for samples again.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                JohnOCFIIundefined 1 Reply Last reply Reply Quote 0
                                • JohnOCFIIundefined
                                  JohnOCFII @dc42
                                  last edited by

                                  @dc42 Any chance yet to re-test the IR sensor with PrintBIte?

                                  1 Reply Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators
                                    last edited by

                                    Thanks for the reminder, I've chased again for a sample.

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    1 Reply Last reply Reply Quote 0
                                    • npm1undefined
                                      npm1
                                      last edited by

                                      Hi,
                                      Would TL-W5MC1 be better than the cylinder inductive sensors or would they be equal in experience and deviation.
                                      Please let us know of ur experience.

                                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                                      1 Reply Last reply Reply Quote 0
                                      • nytundefined
                                        nyt
                                        last edited by nyt

                                        I use the black matte printbite with an ir sensor I got off ebay. It's quite consistent when doing mesh leveling, but sometimes homing is a bit off compared to the leveling.

                                        https://www.ebay.com/itm/Mini-IR-Differential-Height-Sensing-Board-with-1-Cable-3D-Printer/152929325455

                                        alt text

                                        And here you can see the center point, which is the same as the homing probe point, is off by 0.03mm

                                        alt text

                                        1 Reply Last reply Reply Quote 0
                                        • dc42undefined
                                          dc42 administrators
                                          last edited by

                                          To get accurate homing, make sure that the XY position at which you home Z coincides with one of the points in the mesh. This isn't as easy as it sounds, because when you execute G30 to home Z, probing is done at the current location; whereas when you use G29 to generate a height map, the nozzle position is adjusted to allow for the offset of the probe. So in homez.g and homeall.g, choose the XY location that you send the nozzle to before you execute G30 so that it is at the location of a probe point close to the centre of the bed minus the Z probe XY offset that you specified in the G31 command.

                                          Duet WiFi hardware designer and firmware engineer
                                          Please do not ask me for Duet support via PM or email, use the forum
                                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                                          1 Reply Last reply Reply Quote 0
                                          • First post
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA