Duet hardware actually makes it into Thomas Salanderer's videos
-
hey you might take a look at what thease guys are doing for the bldc with encoder
https://odriverobotics.com/#odrive -
@dc42 said in Duet hardware actually makes it into Thomas Salanderer's videos:
@og3d said in Duet hardware actually makes it into Thomas Salanderer's videos:
@dc42
Is implementing closed loop support in hardware and software by an encoders on your radar for next version of duet?We've been keeping an eye on developments in this area, with a view to doing an alternative DueX expansion board that would drive BLDC motors instead of stepper motors. The main problem so far is the lack of suitable inexpensive BLDC motors. The cheap ones used in quadcopters have no gearbox and no sensors, which is OK when you only run the motors at high speeds, but no good for 3D printers. When we need is a BLDC motor with built-in commutation sensors (so that we can run the motor at low speeds), a reduction gearbox (because BLDCs are only efficient at high speeds), and that gearbox must either have very low backlash or else we also need an encoder on the output shaft with a resolution of at least 5000 counts/rev.
@dc42
What do you think about them?
https://hackaday.io/project/11583-odrive-high-performance-motor-controlI was more think of adding support for encoders.
Something like this one.
https://www.cui.com/product/product-resources/amt100-series-modular-encoders.pdf -
@og3d said in Duet hardware actually makes it into Thomas Salanderer's videos:
@dc42
What do you think about them?
https://hackaday.io/project/11583-odrive-high-performance-motor-controlIt looks good, but way overpowered and too expensive for ordinary 3D printers. It might be good if you wanted to print a house though!
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@vlad said in Duet hardware actually makes it into Thomas Salanderer's videos:
Oh well, that's not a review unfortunately. But still nice to hear some news. Hoping he will actually review the board. Maybe he didn't review it because Duet3D folks did not offer him a board? Could be a reason.
We have offered him a board but Tom has a lot on right now!
-
@t3p3tony I will try to ask him on Patreon, I am one of his top supporters there
I would actually love to hear his opinion on this board. I am sure many folks will enjoy such video. -
He has a duet, we see in one of the videos about drivers
Nice img
-
Thanks, and yes we sent him a Duet.
-
@dc42 said in Duet hardware actually makes it into Thomas Salanderer's videos:
@og3d said in Duet hardware actually makes it into Thomas Salanderer's videos:
@dc42
What do you think about them?
https://hackaday.io/project/11583-odrive-high-performance-motor-controlIt looks good, but way overpowered and too expensive for ordinary 3D printers. It might be good if you wanted to print a house though!
Agree, but image how fast the speeds can become.
-
@dc42 said in Duet hardware actually makes it into Thomas Salanderer's videos:
All stepper motor drivers include flyback diodes.
Can you elaborate on this? I have not seen any flyback diodes on the Duet Wifi nor on the Maestro anywhere near the motor drivers.
So is this something that is internal on the TMC2660? What about the TMC2224?I ask because we did manage to kill a TMC2224 by the motor cable coming unplugged while energized on a recent prototype board. I would appreciate any tips on how to make the drivers more robust in this scenario.
-
What I meant to say was that all stepper motor driver chips include flyback diodes. They are built into the output MOSFETs.
There is a section about protecting drivers on the TMC22xx datasheet.
