• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Tips for adjusting Precision Piezo Orion

Scheduled Pinned Locked Moved
Third-party add-ons
8
28
3.6k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    cabal2000 @hevilp
    last edited by 16 Sept 2018, 19:04

    @hevilp said in Tips for adjusting Precision Piezo Onion:

    M574 X1 Y1 Z0 S0

    G28
    Error: G0/G1: insufficient axes homed

    1 Reply Last reply Reply Quote 0
    • undefined
      hevilp
      last edited by hevilp 16 Sept 2018, 19:06

      Das something to setup, what style is your printer?

      You need to Home first X and Y and last Z.

      In the beginning dont use G28 only,

      Use G28 X
      Then G28 Y
      Then G28 Z

      Before you do, tell the printer style and where are the Endstops

      undefined 1 Reply Last reply 16 Sept 2018, 19:08 Reply Quote 0
      • undefined
        cabal2000 @hevilp
        last edited by cabal2000 16 Sept 2018, 19:08

        @hevilp
        Core XY.

        G28 Z
        Error: G0/G1: insufficient axes homed

        1 Reply Last reply Reply Quote 0
        • undefined
          hevilp
          last edited by 16 Sept 2018, 19:12

          Okay:

          ; Endstops
          M574 X1 Y1 S1 ; Set active high endstops
          M574 Z1 S2 ; Define Z to use Probe. Home to Min

          ; Z Probe
          M558 P8 I1 R0.6 F300 Z1

          undefined 1 Reply Last reply 16 Sept 2018, 19:24 Reply Quote 0
          • undefined
            cabal2000 @hevilp
            last edited by cabal2000 16 Sept 2018, 19:24

            @hevilp
            Nope!!
            I only have it connected to the z-stop switch. This is correct right?
            And also, which is the correct one i should clicked on Switch/Unmodulated/simple Ultrasonic etc...?

            1 Reply Last reply Reply Quote 0
            • undefined
              hevilp
              last edited by hevilp 16 Sept 2018, 19:41

              No it comes to the z Probe connection, not the end stop z

              Take a look at the wiring guide from duet for your Board

              undefined 1 Reply Last reply 16 Sept 2018, 19:45 Reply Quote 0
              • undefined
                cabal2000 @hevilp
                last edited by 16 Sept 2018, 19:45

                @hevilp
                Will that makes more sense!! OK, 5v or 3.3v and Z-Probe_mod I am guessing!!

                1 Reply Last reply Reply Quote 0
                • undefined
                  hevilp
                  last edited by 16 Sept 2018, 19:53

                  I dont know your Board, but piezo can do 5v yes

                  undefined 1 Reply Last reply 17 Sept 2018, 00:09 Reply Quote 0
                  • undefined
                    cabal2000 @hevilp
                    last edited by 17 Sept 2018, 00:09

                    @hevilp
                    I think I have that figured out BUT for some reason the z is not going up.

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      Moriquendi
                      last edited by 17 Sept 2018, 15:13

                      I'm do not know the Maestro but...

                      To use the Orion as the Z-endstop and the Z-probe it must be connected to the Z-probe connector. As @hevilp says, your M558 should be...

                      M558 P8 (mode 8, digital, unfiltered) I1 (inverted, active low) R0.6 (wait 0.6s before Z-probe) F300 (probe at 5mm/s) Z1 (probe from 1mm z-height)

                      M558 P8 I1 R0.6 F300 Z1

                      Did you use the Duet online configurator?

                      I'm on holiday at the moment so I don't have access to my printer to check your config against mine.

                      Idris

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        cabal2000
                        last edited by 18 Sept 2018, 22:32

                        @moriquendi So, do I just change the one line or take everything out I just add this line. Sorry for such noobs questions, very very new to Duet boards. And yes i did use the Duet online configurator. I used the "Switch" setting. And set all the endstops to Low End. Z to Z-Probe.

                        undefined 1 Reply Last reply 19 Sept 2018, 20:34 Reply Quote 0
                        • undefined
                          Moriquendi @cabal2000
                          last edited by 19 Sept 2018, 20:34

                          @cabal2000 Just change that line in your config.g

                          Here's the relevant part of my config.g

                          ; Endstops
                          M574 X1 Y1 S0 ; Set active low endstops

                          ; Z-Probe
                          M574 Z1 S2 ; Set endstops controlled by probe
                          M558 P8 I1 H2 R0.5 F300 T6000 ; Set Z probe type to switch and the dive height + speeds
                          G31 P500 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height

                          The important parts are:

                          M574 X1 Y1 S0 ; X and Y endstops active low.

                          M574 Z1 S2 ; Z-endstop active low, controlled by Z-probe.

                          Do you have these lines in your config.g?

                          Idris

                          undefined 1 Reply Last reply 19 Sept 2018, 21:58 Reply Quote 0
                          • undefined
                            cabal2000 @Moriquendi
                            last edited by 19 Sept 2018, 21:58

                            @moriquendi
                            What do you have in your homez?

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              cabal2000
                              last edited by 19 Sept 2018, 22:04

                              This is what I have:

                              ; homez.g
                              ; called to home the Z axis
                              ;
                              ; generated by RepRapFirmware Configuration Tool on Mon Sep 17 2018 22:03:45 GMT-0230 (Newfoundland Daylight Time)
                              G91 ; relative positioning
                              G1 Z5 F6000 S2 ; lift Z relative to current position
                              G90 ; absolute positioning
                              G1 X150 Y150 F6000 ; go to first probe point
                              G30 ; home Z by probing the bed

                              ; Uncomment the following lines to lift Z after probing
                              ;G91 ; relative positioning
                              ;G1 S2 Z5 F100 ; lift Z relative to current position
                              ;G90 ; absolute positioning

                              The head moves to x150 y 150 (center of bed) but when the z starts to rise the head is slowly moving to the left. It isn't staying on center

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                dc42 administrators
                                last edited by 20 Sept 2018, 06:32

                                Perhaps you have axis skew compensation enabled in config.g? It's the M556 command. Not to be confused with M558, which configured the Z probe.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                1 Reply Last reply Reply Quote 0
                                • undefined
                                  Moriquendi
                                  last edited by 20 Sept 2018, 06:47

                                  My homez.g is the same as yours except for different dimensions.

                                  Idris

                                  1 Reply Last reply Reply Quote 0
                                  22 out of 28
                                  • First post
                                    22/28
                                    Last post
                                  Unless otherwise noted, all forum content is licensed under CC-BY-SA