• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Maestro connection/guide halp!

Scheduled Pinned Locked Moved
General Discussion
4
29
2.7k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    dc42 administrators
    last edited by 13 Oct 2018, 15:01

    If both are 0.0.0.0 then your router is not allocating an IP address for the Maestro. Have you tried a different Ethernet cable? Do the LEDs on the Ethernet socket blink?

    Duet WiFi hardware designer and firmware engineer
    Please do not ask me for Duet support via PM or email, use the forum
    http://www.escher3d.com, https://miscsolutions.wordpress.com

    1 Reply Last reply Reply Quote 0
    • undefined
      Fizban
      last edited by 13 Oct 2018, 16:01

      Oh aye they all the lights acts as expected. I'll try a different approach on the router, I might have had the same issue when I installed the pi.

      Ill keep you updated, thanks

      1 Reply Last reply Reply Quote 0
      • undefined
        Fizban
        last edited by 13 Oct 2018, 18:17

        Ok so I made progress. I might have put the files in the wrong place form the start. They are now located in /sys

        I doublechecked that it's connected to my router at .106 via DCHP however I would like to set it as static later on.

        But I stil can't conncet via duettest.local and if I type the ip 192.168.0.106 i get a white screen now with the message:

        Your Duet rejected the HTTP request: page not found

        1 Reply Last reply Reply Quote 0
        • undefined
          dc42 administrators
          last edited by 13 Oct 2018, 19:18

          That message usually means that you do not have the DuetWebControl files in the /web folder of the SD card.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • undefined
            Fizban
            last edited by 13 Oct 2018, 19:27

            Hmm by glance the SD looks like it got all I need. I'll grab a new package and move on to it.
            Thanks

            1 Reply Last reply Reply Quote 0
            • undefined
              Fizban
              last edited by 13 Oct 2018, 20:38

              Ok so erhm. Good news! and bad new! 😞 I've got the DWC working. On another computer for some reason.
              Now I just got a ton of other issues lol.

              My parts fan is running constantly.
              BLtouch is triggered physically, but hardware is not detecting it.

              All my endstops wont trigger, or rather.
              -If I trigger Y the fans stops running and the board disconnects it self from the DWC and shuts down the USB.

              The steppers do however work, I tried to home X and strangely all three axis moved all together. With the classical back 'n forth move of 10mm when no endstop is triggered.

              Seems like I got a long day ahead of me tomorrow, going to unplug it all and try over. However everything seems in order.

              undefined 1 Reply Last reply 14 Oct 2018, 08:32 Reply Quote 0
              • undefined
                Phaedrux Moderator
                last edited by 13 Oct 2018, 23:19

                I think you may want to have another crack at the online configurator and see if you can provide some more accurate details.

                You can also post your config.g here along with a description of your printer details so we can point out what needs to be changed.

                Perhaps this would be of help:

                https://duet3d.dozuki.com/Wiki/Step_by_step_guide

                https://duet3d.dozuki.com/Wiki/Going_from_Marlin_on_Arduino_to_RepRapFirmware_on_Duet

                https://duet3d.dozuki.com/Wiki/BLTouch_Troubleshooting

                https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators @Fizban
                  last edited by 14 Oct 2018, 08:32

                  @fizban said in Maestro connection/guide halp!:

                  -If I trigger Y the fans stops running and the board disconnects it self from the DWC and shuts down the USB.

                  You have the endstop switch wired incorrectly. It's shorting +3.3v to ground when it is triggered.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  undefined 1 Reply Last reply 14 Oct 2018, 11:40 Reply Quote 0
                  • undefined
                    Fizban @dc42
                    last edited by 14 Oct 2018, 11:40

                    @Phaedrux
                    Going through it all now. I'll post specs and config after my next attempt.

                    @dc42
                    I might have, Man this board is nowhere what I'm used to work with 🙂
                    Im going through it again now, hopefully I can run a test later today.

                    Thanks

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      Fizban
                      last edited by 14 Oct 2018, 15:21

                      Ok so I took it all apart and started over.

                      I got all my endstops working, I connected them side by side and not most two outer pins. My bad.
                      I even made my optical endstops working!
                      Bed and hotend heats up!
                      It homes and runs correctly in all directions!

                      Now to setup that BLtouch, but I see I'm not the only one having issues, but I'll take this elsewhere, for now 😉

                      Thanks all!

                      undefined 1 Reply Last reply 14 Oct 2018, 20:16 Reply Quote 0
                      • undefined
                        Phaedrux Moderator @Fizban
                        last edited by 14 Oct 2018, 20:16

                        @fizban said in Maestro connection/guide halp!:

                        Now to setup that BLtouch, but I see I'm not the only one having issues,

                        It's really not that bad.

                        Did you follow the setup guide?

                        https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          Fizban
                          last edited by Fizban 15 Oct 2018, 18:53

                          @Phaedrux
                          Nah not yet, I have more important errors to look into as of now 🙂

                          Getting a new one and I see it's been up quite a few times!

                          I had a somewhat successful print last night. Massive over extrusion and skipping. I did the math wrong, I later realized that I forgot that I some weeks back went from 32 > 16 stepping on the extruder and forgot to take this into account.

                          Anyways, I'm now getting this error !

                          0_1539629771478_17149e28-2c7e-4016-8ea9-f349f7505d0c-image.png

                          Fun fact I'm doing a test cube XYZ it lays down the first layer perfect, starts the second layer, does one round then it stops extruding and this comes up.

                          I did for a brief moment set a higher motor current, cause there's little to no holding power on the steppers. Im used to them being locked down and immoveable!

                          It shortly popped up on Driver2 but I somehow set the direction as reverse by mistake /shrug reverting this fixed it.
                          I checked Vin it's stable.
                          The drivers Arent hot, it extruders 10x100mm no problems

                          I wanted to try extruding on E1 instead of E0 but it wouldn't let me, I think put in the wrong code for it...

                          1 Reply Last reply Reply Quote 0
                          • undefined
                            Phaedrux Moderator
                            last edited by 15 Oct 2018, 19:05

                            https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_definition_section

                            That may help you to reconfigure your tool to use a different extruder drive.

                            Do you still get that error if you disconnect the motor and issue a movement command to the driver? If you no longer get the error that would hint that it is a wiring problem.

                            Z-Bot CoreXY Build | Thingiverse Profile

                            undefined 1 Reply Last reply 15 Oct 2018, 19:07 Reply Quote 0
                            • undefined
                              Fizban @Phaedrux
                              last edited by 15 Oct 2018, 19:07

                              @phaedrux The thing is, it's not complaining till second layer. I can issue ten 100mm extrusions without issues.

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                Phaedrux Moderator
                                last edited by Phaedrux 15 Oct 2018, 19:12

                                What firmware version are you using?

                                I believe this thread may apply to your issue.

                                https://forum.duet3d.com/topic/6607/frequent-short-to-ground-on-z-and-extruder

                                You may need to upgrade to 2.02RC2 if you aren't already and tune your stealth chop / spread cycle setup.

                                https://duet3d.dozuki.com/Wiki/Gcode#Section_M569_Set_motor_driver_direction_enable_polarity_and_step_pulse_timing

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 0
                                • undefined
                                  Fizban
                                  last edited by 15 Oct 2018, 19:17

                                  2.01beta I'll update and look into this. Thank you very much!

                                  1 Reply Last reply Reply Quote 0
                                  • undefined
                                    Fizban
                                    last edited by 15 Oct 2018, 19:41

                                    0_1539632457906_3812137b-388f-4f05-9476-fa9753f9ca37-image.png

                                    This can't be right.
                                    Besides it's cloning all my macros/Gcodes all the time. Trying to revert this lol

                                    undefined 1 Reply Last reply 15 Oct 2018, 19:43 Reply Quote 0
                                    • undefined
                                      Phaedrux Moderator @Fizban
                                      last edited by 15 Oct 2018, 19:43

                                      @fizban what file did you use?

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      1 Reply Last reply Reply Quote 0
                                      • undefined
                                        Fizban
                                        last edited by 15 Oct 2018, 19:43

                                        0_1539632611271_22b65f8b-4a2e-4cea-a803-e2dd1f3dd3b8-image.png
                                        these

                                        1 Reply Last reply Reply Quote 0
                                        • undefined
                                          Fizban
                                          last edited by 15 Oct 2018, 19:51

                                          Ok nevermind, Now it actually updated. I had to drag and drop to make it work.

                                          Lol I guess I'll learn this DWC some day =D
                                          It's also a lot more responsive now on the interface!

                                          undefined 1 Reply Last reply 15 Oct 2018, 19:59 Reply Quote 0
                                          13 out of 29
                                          • First post
                                            13/29
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA