Maestro connection/guide halp!

[Fizban]

Ok so erhm. Good news! and bad new! I've got the DWC working. On another computer for some reason.
Now I just got a ton of other issues lol.

My parts fan is running constantly.
BLtouch is triggered physically, but hardware is not detecting it.

All my endstops wont trigger, or rather.
-If I trigger Y the fans stops running and the board disconnects it self from the DWC and shuts down the USB.

The steppers do however work, I tried to home X and strangely all three axis moved all together. With the classical back 'n forth move of 10mm when no endstop is triggered.

Seems like I got a long day ahead of me tomorrow, going to unplug it all and try over. However everything seems in order.

[Phaedrux]

I think you may want to have another crack at the online configurator and see if you can provide some more accurate details.

You can also post your config.g here along with a description of your printer details so we can point out what needs to be changed.

Perhaps this would be of help:

https://duet3d.dozuki.com/Wiki/Step_by_step_guide

https://duet3d.dozuki.com/Wiki/Going_from_Marlin_on_Arduino_to_RepRapFirmware_on_Duet

https://duet3d.dozuki.com/Wiki/BLTouch_Troubleshooting

https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter

[dc42]

@fizban said in Maestro connection/guide halp!:

-If I trigger Y the fans stops running and the board disconnects it self from the DWC and shuts down the USB.

You have the endstop switch wired incorrectly. It's shorting +3.3v to ground when it is triggered.

[Fizban]

@Phaedrux
Going through it all now. I'll post specs and config after my next attempt.

@dc42
I might have, Man this board is nowhere what I'm used to work with
Im going through it again now, hopefully I can run a test later today.

Thanks

[Fizban]

Ok so I took it all apart and started over.

I got all my endstops working, I connected them side by side and not most two outer pins. My bad.
I even made my optical endstops working!
Bed and hotend heats up!
It homes and runs correctly in all directions!

Now to setup that BLtouch, but I see I'm not the only one having issues, but I'll take this elsewhere, for now

Thanks all!

[Phaedrux]

@fizban said in Maestro connection/guide halp!:

Now to setup that BLtouch, but I see I'm not the only one having issues,

It's really not that bad.

Did you follow the setup guide?

https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch

[Fizban]

@Phaedrux
Nah not yet, I have more important errors to look into as of now

Getting a new one and I see it's been up quite a few times!

I had a somewhat successful print last night. Massive over extrusion and skipping. I did the math wrong, I later realized that I forgot that I some weeks back went from 32 > 16 stepping on the extruder and forgot to take this into account.

Anyways, I'm now getting this error !

Fun fact I'm doing a test cube XYZ it lays down the first layer perfect, starts the second layer, does one round then it stops extruding and this comes up.

I did for a brief moment set a higher motor current, cause there's little to no holding power on the steppers. Im used to them being locked down and immoveable!

It shortly popped up on Driver2 but I somehow set the direction as reverse by mistake /shrug reverting this fixed it.
I checked Vin it's stable.
The drivers Arent hot, it extruders 10x100mm no problems

I wanted to try extruding on E1 instead of E0 but it wouldn't let me, I think put in the wrong code for it...

[Phaedrux]

https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_definition_section

That may help you to reconfigure your tool to use a different extruder drive.

Do you still get that error if you disconnect the motor and issue a movement command to the driver? If you no longer get the error that would hint that it is a wiring problem.

[Fizban]

@phaedrux The thing is, it's not complaining till second layer. I can issue ten 100mm extrusions without issues.

[Phaedrux]

What firmware version are you using?

I believe this thread may apply to your issue.

https://forum.duet3d.com/topic/6607/frequent-short-to-ground-on-z-and-extruder

You may need to upgrade to 2.02RC2 if you aren't already and tune your stealth chop / spread cycle setup.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M569_Set_motor_driver_direction_enable_polarity_and_step_pulse_timing

[Fizban]

2.01beta I'll update and look into this. Thank you very much!

[Fizban]

This can't be right.
Besides it's cloning all my macros/Gcodes all the time. Trying to revert this lol

[Phaedrux]

@fizban what file did you use?

[Fizban]

these

[Fizban]

Ok nevermind, Now it actually updated. I had to drag and drop to make it work.

Lol I guess I'll learn this DWC some day =D
It's also a lot more responsive now on the interface!

[Fizban]

@Phaedrux

what the actual f.. Oo

[Phaedrux]

@fizban Have you power cycled after the update?

[Fizban]

I have, I'll re-slice it file lol. I think klipper did similar to me before I switched tbf.

[Fizban]

Success!
I'm now printing again, it sounds different so I take it that the firmware altered something.

I'll look into the interpolation/stealthchop thingie tomorrow.

Right now I'd better get downstairs to the missus! She feels neglected the past days

Thanks @Phaedrux you know your duet! t's much appreciated!!

[Duckle]

I think the newer firmware switches to spreadcycle to maintain torque at higher speeds.