Issues with macros halting the printer.

[brunofporto]

ok... Pinned down the issue when using M291 with the parameter S0 - If I do not use S0 (using S1 instead) then the issues of halting the printer without doing anything does not happen.

Nope... happened again even with all S0s as S1s

[Phaedrux]

Can you post your homeall as well? Would help to see what is happening when you call g28

[dc42]

Please tell us which firmware version you are using, and try 2.02RC4 if you are using an older version.

[brunofporto]

@dc42 I have this issue at least since 2.02RC3 at least (not sure about earlier betas). Currently with RC4.

[dc42]

Please provide the contents of beep.g too, and I will try those macros out on my printers.

[brunofporto]

@phaedrux said in Issues with macros halting the printer.:

Can you post your homeall as well? Would help to see what is happening when you call g28

1_1542801481154_homeall.g 0_1542801481139_config.g

; homeall.g
; called to home all axes
;
; Home XY for Z homing
;
G91                ; relative positioning
G1 Z10 F200 S2      ; lift head relative to current position
M400		   ; make sure everything has stopped before we make changes
M913 X50 Y50	   ; set X Y motors to 50% of their normal current for homing
M98 P"0:/sys/m_set_low_speeds.g"     ; set lower Z speeds and accelerations
; Home XY for Z homing
;
;==============Home X====================
;
G1 S1 X-305 Y-335 F4800 ; move quickly diagonally to hit X or Y
M400
G1 X10 Y10 F1000          ; go back a few mm
G1 S1 X-305 F4800       ; move quickly to X axis
G1 X10 F1000             ; go back a few mm

;==============Home Y====================
;
M400
G1 S1 Y-335 F4800 ; move quickly to X axis endstop and stop there (first pass)
G1 Y10 F1000       ; go back a few mm
;==============Home Z====================
;
M400
G90                            ; absolute positioning
M98 P"0:/macros/Center_Probe"; move to center of bed

; Probe the bed
;
M558 A1 F350			; Set single probing at faster feed rate
G30 				; Do a single probe to home our Z axis
M558 A10 F100			; Set tripple probing at slower feed rate
G30				; Probe again to get a more accurate position

M400		   ; make sure everything has stopped before we make changes
M98 P"0:/sys/m_set_normal_speeds.g"  ; set normal Z speeds and accelerations
M913 X100 Y100	   ; set X Y motors to 100% of their normal current

[brunofporto]

Just now. Turned on the printer. Did a G32 command (bed.g attached) and clicked at the Z Probe calibration macro (below). And.... Busy doing nothing.....

Just to reinforce: This "busy halt" does not occur if I execute the macro line by line at the console.

Here is the macro:

M291 P"Grid bed compensation map and ZProbe trigger height will be cleared. Ok or Cancel?" R"WARNING" S3 ; User must click OK or cancel.

M561			; Disable any current bed compensation

G29 S2			; Clear mesh bed compensation perameters

M291 P"Please wait while the bed and tool is being heated up" R"Please Wait" S1 T0 ; Display message

M140 S60		; Set bed temp to 60 and release

G32			; Home all axis

M116                    ; Wait for bed heating

M104 S210		; Set nozzle to 210 and release

M116                    ; Wait for all to heat

M292

M98 P"0:/macros/Center_Nozzle"; move to center of bed

M291 P"Nozzle will now move to center of bed to reset Z0 and calibrate probe" S2

G31 Z0				; Reset zprobe trigger height
G92 Z25				; Reset z to 25 to allow jogging up to touch bed to nozzle

M98 P"0:/sys/m_set_low_speeds.g"     ; set lower Z speeds and accelerations

M98 P/MACROS/SUBMACROS/BEEP.G

M291 P"Jog the Z Axis until the bed and nozzle are touching and click OK" R"Setting Z=0" Z1 S2

G92 Z0			; Set z = 0

M291 P"Probe will now measure trigger height 10 times" R"ZProbe Trigger Height Calibration" S2

M98 P"0:/macros/Center_Probe"   ;0 move to center of bed
G1 Z10 F4000 	                ; Move probe to center and drop bed for nozzle clearance

M401
G30 P0 X189 Y140 Z-9999
G30 P1 X189 Y140 Z-9999
G30 P2 X189 Y140 Z-9999
G30 P3 X189 Y140 Z-9999
G30 P4 X189 Y140 Z-9999
G30 P5 X189 Y140 Z-9999
G30 P6 X189 Y140 Z-9999
G30 P7 X189 Y140 Z-9999
G30 P8 X189 Y140 Z-9999
G30 P9 X189 Y140 Z-9999 S-1
M402

M104 S0		; Set nozzle to 0 and release
M140 S0		; Set bed to 0 and release

M400

M98 P"0:/sys/m_set_normal_speeds.g"  ; set normal Z speeds and accelerations

M291 P"Probing complete. Turning off heaters and homing axis." S1


M98 P/MACROS/SUBMACROS/BEEP.G

Here is bed.g

; bed.g
; called to perform automatic bed compensation via G32

M671 X-48:326 Y140:140        ; Define positions of lead screws again
M561                ; clear any bed transform
G28                 ; home all axes
; Probe the bed at 2 points
M401
G30 P0 X22 Y140 H0 Z-99999
G30 P1 X314 Y140 H0 S2 Z-99999 
G28 Z
M402

[dc42]

Just a reminder that I asked yesterday for your beep.g macro too.

[brunofporto]

@dc42 Here it is!

By the way... I cannot play any "tunes" without adding these timers between each M300. At least with the PanelDue attached.

M300 S2000 P300
G4 P300
M300 S2000 P300
G4 P300
M300 S2000 P300

[dc42]

@brunofporto said in Issues with macros halting the printer.:

@dc42 Here it is!

By the way... I cannot play any "tunes" without adding these timers between each M300. At least with the PanelDue attached.

PanelDue has no flow control, deliberately to avoid holding up the Duet. But I could implement a short queue of beeps pending in the PanelDue firmware.

[dc42]

@brunofporto said in Issues with macros halting the printer.:

M291 P"Please wait while the bed is being heated up" R"Please Wait" S0 T0 ; Display message
M140 S60 ; Set bed temp to 60
G32 ; Home all axis
M116 ; Wait for heating
M292 Close message
M291 P"Please wait while the bed is being heated up" R"Please Wait" S3 T0 ; Display message
M98 P/MACROS/SUBMACROS/BEEP.G

I'm sorry, I can't reproduce the problem using either your test macro or the full macro (I had to make up the contents of 4 more macros thai it called).

By the way, your test macro is missing a semicolon before the comment "Close message" on the M292 line.

How reproducible is the problem?

My best guess as to why it is hanging is that when you cancel the M291 message box, the M292 command to tell the Duet that it has been cancelled is not being received and/or processed. So I have two suggestions:

1. Connect a PC running YAT or Pronterface etc. and send M111 S1 P3 to enable GCodes debugging. Then you will be able to see whether the M292 command is received.

2. Next time it appears to be stuck, try sending M292 and see whether that un-freezes it.

[brunofporto]

Just happened again...

Freshly started board.

G32

Sent the macro from the 22/11/2018 message above. Appeared the messages informing that the bed and hotend would be heated. Clicked ok and.... halted.

[dc42]

So did you try my suggestions?

[brunofporto]

The complete sequence and used files:

Sent G32 and waited for it to finish:

Executed the Macro:

Clicked ok and then.... halted doing nothing:

Attached bed.g, calibration macro and all sub macros related.

Thanks.

6_1543257949998_bed.g 5_1543257949998_4_Calibrate_ZProbe.g 4_1543257949998_beep.g 3_1543257949998_Center_Nozzle.g 2_1543257949998_Center_Probe.g 1_1543257949998_m_set_low_speeds.g 0_1543257949998_m_set_normal_speeds.g

[brunofporto]

@dc42 I'll..... But the printer is far from a computer and heavy...... As soon as I am able to move it and connect an USB directly I'll try

[brunofporto]

@dc42 Please, in order to avoid moving it unnecessarily, is it possible to monitor via telnet or something?

[dc42]

@brunofporto said in Issues with macros halting the printer.:

@dc42 Please, in order to avoid moving it unnecessarily, is it possible to monitor via telnet or something?

Yes, use the M586 command to enable Telnet.

[brunofporto]

@dc42 said in Issues with macros halting the printer.:

Next time it appears to be stuck, try sending M292 and see whether that un-freezes it

ok.... It receives the M292 command, confirms it, but the printer still busy doing nothing

m111 s1 p3
Debugging enabled for modules: GCodes(3)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15)
ok
m292
ok
m292
ok

[dc42]

Can you send M122 and get a report?

[brunofporto]

@dc42 Sure! Did while "busy" doing nothing after reproducing the issue:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02RC4(RTOS) running on Duet Ethernet 1.02 or later
Board ID: 08DGM-956GU-DJMSN-6J9D4-3SJ6S-1BNHD
Used output buffers: 1 of 20 (16 max)
=== RTOS ===
Static ram: 27476
Dynamic ram: 98660 of which 12 recycled
Exception stack ram used: 496
Never used ram: 4428
Tasks: NETWORK(ready,328) HEAT(blocked,1232) MAIN(running,1660) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:03:59 ago, cause: software
Last software reset at 2018-11-26 17:26, reason: User, spinning module GCodes, available RAM 4436 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 24.7, current 25.8, max 26.3
Supply voltage: min 24.5, current 24.6, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/250
Driver 1: standstill, SG min/max 0/242
Driver 2: standstill, SG min/max 0/162
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max 0/177
Date/time: 2018-11-26 17:30:11
Cache data hit count 546791891
Slowest loop: 51.83ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 237, MaxWait: 95242ms, Underruns: 0, 0
Scheduled moves: 35, completed moves: 36
Bed compensation in use: none
Bed probe heights: -0.024 -0.046 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 1 in use
Movement lock held by null
http is doing "M291 P"Please wait while the bed and tool is being heated up" R"Please Wait" S1 T0 " in state(s) 0 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 51.30ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(2) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0 sensor: position 8.22, ok, framing errors 0, parity errors 0, no calibration data