• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Question delta steps calibration..

Scheduled Pinned Locked Moved
General Discussion
5
8
856
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    peirof
    last edited by peirof 2 May 2019, 15:24 5 Feb 2019, 09:57

    Hi,

    After discover that the last print issues comes for axis steps calibration...

    And after try to recalibrate steps for mm, with partial exit. I have a dude. The methods I have read, are clear... But they are relative a cartesiano printer...

    The process of steps of axis calibration, its the same that a cartesian?

    I think remember in M92, in config.g.

    I am using the cartesian system.... And, close, but no I the hole

    undefined 1 Reply Last reply 5 Feb 2019, 14:26 Reply Quote 0
    • undefined
      Veti
      last edited by 5 Feb 2019, 11:02

      on a delta printer the dimension of a print come mainly from a correct rod length.

      see http://boim.com/DeltaUtil/CalDoc/Calibration.html

      undefined 1 Reply Last reply 5 Feb 2019, 12:51 Reply Quote 0
      • undefined
        peirof @Veti
        last edited by 5 Feb 2019, 12:51

        @veti thanks.... Bufff, its very good.

        1 Reply Last reply Reply Quote 0
        • undefined
          mrehorstdmd @peirof
          last edited by 5 Feb 2019, 14:26

          @peirof A long time ago I was learning to speak Japanese and I made many mistakes in word selection and usage and always appreciated it when someone corrected me, so I hope you feel the same way. I have noticed your use of the word "dude" in many posts.

          When you have been using "dude", you should be using the word "question". This post, for example, should be titled something like "Questions about delta steps calibration".

          "Dude" has several uses- many listed here: https://www.wordnik.com/words/dude and here: https://www.merriam-webster.com/dictionary/dude , but none of them means anything like "question".

          This short video clip illustrates another use of "dude": https://www.youtube.com/watch?v=xJjCnWm5cvE

          https://drmrehorst.blogspot.com/

          undefined undefined 2 Replies Last reply 5 Feb 2019, 15:25 Reply Quote 0
          • undefined
            peirof @mrehorstdmd
            last edited by 5 Feb 2019, 15:25

            @mrehorstdmd thanks for the warning....

            1 Reply Last reply Reply Quote 0
            • undefined
              richardmckenna @mrehorstdmd
              last edited by 5 Feb 2019, 19:25

              @mrehorstdmd I love this forum everyone is always so helpful. I don’t think I’ve ever had a question go unanswered or a problem not resolved. Definitely one of the best 3d printing forums out there.

              1 Reply Last reply Reply Quote 1
              • undefined
                dc42 administrators
                last edited by 6 Feb 2019, 15:19

                @peirof, assuming all 3 towers are built the same and have similar belt tension, then all 3 should have the same steps/mm. You should can calculate this value, or measure it from the Z height of your prints.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • undefined
                  peirof
                  last edited by 7 Feb 2019, 05:43

                  hi,

                  i will recheck....

                  1 Reply Last reply Reply Quote 0
                  6 out of 8
                  • First post
                    6/8
                    Last post
                  Unless otherwise noted, all forum content is licensed under CC-BY-SA