Unsolved Prusa upgraded to duet, weird extrusion
-
they are called vfa
the prusa board has specific tuning on the tmc2130 which are not possible on the tmc2660.
see
https://github.com/prusa3d/Prusa-Firmware/issues/428
and here
for a real fix see here
https://forum.prusaprinters.org/forum/original-prusa-i3-mk3s-mk3-user-mods-octoprint-enclosures-nozzles-.../stepper-motor-upgrades-to-eliminate-vfa-s-vertical-fine-artifacts/closed Constant vertical banding #428
-
So basically my frame is so good(at least stiff) that the stepper drivers being "cheap" is showing now? Now that's a paddlin'.
-
yes. i had the same problem. i kept improving my printer until i arrived at those artefacts as well.
took my a while to figure that one out. replaced a lot of other parts before swapping to 0.9 stepper drivers. -
Did you swap just X and Y steppers or all of them?
-
@Murloc992 said in Prusa upgraded to duet, weird extrusion:
Did you swap just X and Y steppers or all of them?
i only swapped x and y
https://e3d-online.com/high-torque-motor
(be aware i only found out they have no cut shaft, but they work nonetheless.) -
@Veti said in Prusa upgraded to duet, weird extrusion:
(be aware i only found out they have no cut shaft, but they work nonetheless.)
You mean no flat spot?
-
yes. i mainly got them because those were the only ones with swappable cable.
a good alternative are the steppers suggested here
https://www.thingiverse.com/thing:3382718 -
Maybe you have pics of print results with E3D motors? I have some motors with same specs to buy locally, but E3D are.. cheaper?
-
those where posted here
https://forum.duet3d.com/topic/9438/artefacts-on-walls -
Thank you. Now I just need to wait till my steppers arrive and update this post.
Going to change X/Y and E. -
So I've upgraded my motors to E3D ones:
X/Y: https://e3d-online.com/high-torque-motor
E: https://e3d-online.com/compact-but-powerful-motorNow I have a WEIRD pattern that comes from the extruder motor:
(I know, my first layer is too high, I just wanted to test ASAP)I can hear the extruder motor making such "patterned noise"..
I have started at 1000mA current(both driver and motor cool), then tried to make it 1400mA(driver a bit hotter than lukewarm, motor cool/warm) with no change in behavior. What is this artifact?
-
@Murloc992 said in Prusa upgraded to duet, weird extrusion:
Now I have a WEIRD pattern that comes from the extruder motor:
are you sure its from the extruder? how does it look if you switch back to the old motor on the extruder?
-
I am sure, it's making pulsing noise even when spinning alone, without any plastic or idler engaged.. The old one doesn't pulse.. I have tried increasing microsctepping and disabling interpolation (nothing), reducing current(nothing), increasing current to maximum(heat increased only)..
This is the best I got:
The pattern is uniform on all sides.
Last time I had it was when I had too thin wires for my motor on an old printer and wires were heating up. But these are E3D cables, I haven't even changed the pins, tried different cables too and they are not heating up at all even at maximum current..
The one I had on my old printer was extreme.. and fixed after changing the extruder cabling.
-
Maybe this could be related to low voltage? I use 12V. Also I got an advice to attempt to reduce microstepping of the extruder motor to 8 microsteps. I will lose the interpolation though.. Will this matter?
Need an expert here.
-
I'd say that somewhere in your extruder drive, a gear is running eccentrically, or there's some other mechanical factor that's causing the the filament to speed up and slow down as it passes through the extruder. Is the stepper motor geared to the hobbed drive, or directly connected? I'd look if the gear on the motor shaft is running eccentrically, due to the hole being off centre, particularly if it's a geared extruder drive, as this would give the short frequency of over/under extrusion you're seeing. If you're using Chinese cloned gears (I think the Bear uses Bondtech BMG parts), this is quite likely!
Edit: Could also be caused by using very coarse hobbed drive.
Ian
-
This might be a possibility. I use a genuine Prusa MK2.5S that was torn apart and resurrected into a Full Bear + Bear Extruder + Duet + New motors(now).
The gears are genuine Bondtech, extruder is as direct as it gets (Bear Extruder), but I wonder how can it be eccentric.. With old motor I didn't have this.. Maybe a difference in flatspots? Or could it have happened if I tightened onto the flatspot a bit angled? Maybe a bent motor shaft (I hope not..)?
-
@Murloc992 Quite possibly one of those! As it's so consistent, I'd think it has to be mechanical. If you can't spot anything obvious, maybe refit the old motor and revert extruder settings in config.g?
Ian
-
Every time I have to take the extruder of a prusa apart(including the wiring loom) I die a little inside, but I guess I will have to if I can't center the main gear..
Will need to upgrade the extruder wiring loom someday to use a PCB at the back, so the wiring loom will be independent..
-
The fact that you can hear it pulsing makes me think it's the motor itself. Does it still sound like that if you run it free of any connection to the extruder gearing?
-
The motor shaft is straight, the gear is straight. Motor switch didn't help. All of them pulse. I will try reducing my microsteps to 8.. Maybe somebody knows about a TMC parameter called "Velocity"? I remember there's some register adjustments but I can't find it at the moment..
