Help: Temp Sensors and Homing Issues

94118

Would i be all good to load filament and try a test print

94118

Machine movement controls not responsive i click on the fine movement tabs and it does noting machine is in idle

Phaedrux

So the printer will home properly but then you can't use the jog buttons in DWC?

94118

Yes that is correct

Phaedrux

Can you send movement commands in the console?
Do the paneldue move buttons work?

94118

No i cannot send commands from console or paneldue

Phaedrux

Please post your current config.g and homing files so I can see what state your machine would be in after homing.

94118

config (1).g homex.g homey.g homez.g

Phaedrux

In homeX you should have a negative move to back off the endstops.

G91               ; relative positioning
G1 H1 X235 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000    ; go back a few mm
G1 H1 X235 F360  ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Should be

G91               ; relative positioning
G1 H1 X235 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X-5 F6000    ; go back a few mm
G1 H1 X235 F360  ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Your homey has the negative, but you don't need the H2 on the second move.

G91              ; relative positioning
G1 H1 Y215 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y-5 F6000  ; go back a few mm
G1 H1 Y215 F360  ; move slowly to Y axis endstop once more (second pass)
G90              ; absolute positioning

Should be

G91              ; relative positioning
G1 H1 Y215 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y-5 F6000  ; go back a few mm
G1 H1 Y215 F360  ; move slowly to Y axis endstop once more (second pass)
G90              ; absolute positioning

Your homez only has a single homing pass. You may want to add a second slower pass. You're also missing the G90 at the end, which could be your movement problem.

G91               ; relative positioning
G1 H1 Z200 F1800 ; move Z up until the endstop is triggered
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)

Should be

G91               ; relative positioning
G1 H1 Z200 F1800 ; move Z up until the endstop is triggered
G1 Z-5
G1 H1 Z200 F360 ; second pass
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)
G90 ; absolute positioning

94118

Got it to home correctly still cannot use jog controls for fine movement

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

jog controls for fine movement

What exactly do you mean by that? Can you post a photo of what you're trying to use?

94118

https://drive.google.com/open?id=1E9Nnj0lRRrosyiqkRENvNrMgNKRmSi7d
https://drive.google.com/open?id=1E9ZpqFKI_MspoPvdRPRjLaykGRvhTB9-

I would use the jog controls for filament load and unload as well as jams or clogging

Phaedrux

The extruder motor won't move unless it's at printing temp.

Are the x and y and z jog buttons working?

94118

they will work only if i press the plus side of the controls then press the negative side

Phaedrux

Ok that probably means that your endstop positions and/or your motor directions aren't correct.

Where is the X endstop? Left or right side?
Where is the Y endstop? Front or back?

Perhaps take a look at this guide on commissioning a printer: https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39

94118

X is at the Right, y is at the Left rear corner

Phaedrux

; Endstops
M574 X1 S1 P"!xstop"

That should be

; Endstops
M574 X2 S1 P"!xstop"

Because your X endstop is at the high end of travel on the right side.

Change that and see if it works better after homing.

94118

when i changed it from x1 to x2 motor direction went in opposite direction so i changed it back to x1

94118

Should i change my "Z" endstop from x2 to x1 cause current tool postition read (x230, y210, z0) i think it should be 200 or 195

94118

Failed to load filaments
Directory 0:/filaments not found

i was trying to setup a filaments list for PLA, ABS, PetG