Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Initial Setup With new Duet 3

    Scheduled Pinned Locked Moved
    Firmware installation
    4
    21
    664
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • mrenz999undefined
      mrenz999
      last edited by

      I will upload my config.g file. I can't get the endstops to configure. They are simple open/close no power.

      ; Configuration file for Duet 3 (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 21:37:29 GMT-0700 (Pacific Daylight Time)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"Duet 3" ; set printer name
      M669 K1 ; select CoreXY mode

      ; Drives
      M569 P0.0 S1 ; physical drive 0.0 goes forwards
      M569 P0.1 S1 ; physical drive 0.1 goes forwards
      M569 P0.2 S0 ; physical drive 0.2 goes backwards
      M569 P0.3 S1 ; physical drive 0.3 goes forwards
      M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
      M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X330 Y330 Z400 S0 ; set axis maxima

      ; Endstops
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M558 P2 C"io3.in+io3.out" H5 F120 T6000 ; set Z probe type to modulated and the dive height + speeds
      M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
      G31 P500 X20 Y0 Z4 ; set Z probe trigger value, offset and trigger height
      M557 X30:260 Y20:260 S20 ; define mesh grid

      ; Heaters
      M308 S0 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp1
      M950 H0 C"out1" T0 ; create bed heater output on out1 and map it to sensor 0
      M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp0
      M950 H1 C"out0" T1 ; create nozzle heater output on out0 and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

      ; Fans
      M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
      M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
      M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      ; Miscellaneous
      M575 P1 S1 B57600 ; enable support for PanelDue
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

      Phaedruxundefined 1 Reply Last reply Reply Quote 0
      • dc42undefined
        dc42 administrators
        last edited by dc42

        I don't see any M574 commands for the X and Y endstops.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        mrenz999undefined 1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator @mrenz999
          last edited by

          @mrenz999 said in Initial Setup With new Duet 3:

          I can't get the endstops to configure.

          Were you using the web configurator?

          Z-Bot CoreXY Build | Thingiverse Profile

          1 Reply Last reply Reply Quote 0
          • mrenz999undefined
            mrenz999 @dc42
            last edited by

            @dc42 Yes I used the web firmware configurator. I put in end stops. Pretty
            new to Duet.

            1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator
              last edited by

              Can you show a screen shot of what you had selected?

              Z-Bot CoreXY Build | Thingiverse Profile

              mrenz999undefined 1 Reply Last reply Reply Quote 0
              • mrenz999undefined
                mrenz999 @Phaedrux
                last edited by

                @Phaedrux
                ; Configuration file for Duet 3 (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jun 14 2020 08:19:17 GMT-0700 (Pacific Daylight Time)

                ; General preferences
                G90 ; send absolute coordinates...
                M83 ; ...but relative extruder moves
                M550 P"Duet 3" ; set printer name
                M669 K1 ; select CoreXY mode

                ; Drives
                M569 P0.0 S1 ; physical drive 0.0 goes forwards
                M569 P0.1 S1 ; physical drive 0.1 goes forwards
                M569 P0.2 S0 ; physical drive 0.2 goes backwards
                M569 P0.3 S1 ; physical drive 0.3 goes forwards
                M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
                M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X330 Y330 Z400 S0 ; set axis maxima

                ; Endstops
                M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin !io0.in
                M574 Y1 S1 P"!io1.in" ; configure active-high endstop for low end on Y via pin !io1.in
                M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                ; Z-Probe
                M558 P2 C"io3.in+io3.out" H5 F120 T6000 ; set Z probe type to modulated and the dive height + speeds
                M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
                G31 P500 X20 Y0 Z4 ; set Z probe trigger value, offset and trigger height
                M557 X30:260 Y20:260 S20 ; define mesh grid

                ; Heaters
                M308 S0 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp1
                M950 H0 C"out1" T0 ; create bed heater output on out1 and map it to sensor 0
                M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                M140 H0 ; map heated bed to heater 0
                M143 H0 S120 ; set temperature limit for heater 0 to 120C
                M308 S1 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp0
                M950 H1 C"out0" T1 ; create nozzle heater output on out0 and map it to sensor 1
                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                ; Fans
                M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
                M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
                M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
                M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
                M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
                M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

                ; Tools
                M563 P0 D0 H1 F0 ; define tool 0
                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                ; Custom settings are not defined

                ; Miscellaneous
                M575 P1 S1 B57600 ; enable support for PanelDue
                M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                M501

                Lol went back in and sure enough I did not select them. So now they are in there but they are backwards, triggers when not triggered. So I guess I will have to switch the wires.

                deckingmanundefined 1 Reply Last reply Reply Quote 0
                • deckingmanundefined
                  deckingman @mrenz999
                  last edited by

                  @mrenz999 said in Initial Setup With new Duet 3:

                  Lol went back in and sure enough I did not select them. So now they are in there but they are backwards, triggers when not triggered. So I guess I will have to switch the wires.

                  No. It sounds like you've specified active high and they are active low so the configurator has put a "!" before the pin name to invert the input. Just take out those exclamation marks in the M574 commands and you should be good.

                  Ian
                  https://somei3deas.wordpress.com/
                  https://www.youtube.com/@deckingman

                  mrenz999undefined 1 Reply Last reply Reply Quote 0
                  • mrenz999undefined
                    mrenz999 @deckingman
                    last edited by

                    @deckingman
                    That's easy, thank you. The next thing I have to figure out is I have a simpley IR device for my z probe. 3 wire. On the
                    Board io3 I used the first 3 pins starting at 5v which it is 5 v. It has it's own light and signals light on when it detects
                    the plate and off when it doesn't. The software says not triggered and never changes.

                    dc42undefined 1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators @mrenz999
                      last edited by

                      @mrenz999 said in Initial Setup With new Duet 3:

                      @deckingman
                      That's easy, thank you. The next thing I have to figure out is I have a simpley IR device for my z probe. 3 wire. On the
                      Board io3 I used the first 3 pins starting at 5v which it is 5 v. It has it's own light and signals light on when it detects
                      the plate and off when it doesn't. The software says not triggered and never changes.

                      It sounds that you have the output of the IR sensor connected to IO3_OUT. Connect it to IO3_IN instead.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      mrenz999undefined 1 Reply Last reply Reply Quote 0
                      • mrenz999undefined
                        mrenz999 @dc42
                        last edited by

                        @dc42
                        Will do.. Thank you.

                        1 Reply Last reply Reply Quote 0
                        • mrenz999undefined
                          mrenz999
                          last edited by

                          Not sure if I should stay in this same thread or make a new one. I have a corexy and I believe either my x or y stepper motor is backwards. How do I tell ? I tried to home and all kinds of crazy grinding happened as the head jerked around. It's setup with x on the back left and y on the front right. Zonestar z9m3 is the model. Is there a way for me to test which way they are moving and which way they should be moving ?

                          deckingmanundefined 1 Reply Last reply Reply Quote 0
                          • deckingmanundefined
                            deckingman @mrenz999
                            last edited by

                            @mrenz999 said in Initial Setup With new Duet 3:

                            Not sure if I should stay in this same thread or make a new one. I have a corexy and I believe either my x or y stepper motor is backwards. How do I tell ? I tried to home and all kinds of crazy grinding happened as the head jerked around. It's setup with x on the back left and y on the front right. Zonestar z9m3 is the model. Is there a way for me to test which way they are moving and which way they should be moving ?

                            Take a gander at this https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCoreXYPrinter

                            Scroll down to the section entitled testing motor movement and run through the steps listed there.

                            Ian
                            https://somei3deas.wordpress.com/
                            https://www.youtube.com/@deckingman

                            mrenz999undefined 1 Reply Last reply Reply Quote 0
                            • mrenz999undefined
                              mrenz999 @deckingman
                              last edited by

                              @deckingman I gave that a shot. Had to make changes and both X and Y with the G1 S2 X10 F3000 command moved the head forward x and y diagonally. I tried to home the X and it moves negatively towards the Y Home and I home x and it sits there and makes a grinding sound. When I home z it moves up to the end stop which changes to 1000 but it doesn't stop it presses the Hotend into the bed. It activates around 5 mm from the bed.

                              1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator
                                last edited by

                                Where are the endstops physically located on the printer? This will determine how you setup the M574 command. That will also dictate the direction of movement for the homing files. Those things are dictated by the physical location of the endstops. The motor directions need to be resolved separately based on the corexy motor tests.

                                So tell us where the endstops are physically located and post your homing files as well.

                                Z-Bot CoreXY Build | Thingiverse Profile

                                mrenz999undefined 2 Replies Last reply Reply Quote 0
                                • mrenz999undefined
                                  mrenz999 @Phaedrux
                                  last edited by mrenz999

                                  @Phaedrux So looking down on the printer from above. The X motor is in the back left corner. The endstop for it is on the right side of the of the Hotend. The Y motor is in the back on the right side of the printer and the endstop for it is at the motor in the far back righthand corner of the printer.
                                  So the printer is homed at the far right back corner.

                                  1 Reply Last reply Reply Quote 0
                                  • mrenz999undefined
                                    mrenz999 @Phaedrux
                                    last edited by

                                    @Phaedrux
                                    ; homeall.g
                                    ; called to home all axes
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:21 GMT-0700 (Pacific Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z5 F6000 ; lift Z relative to current position
                                    G1 H1 X-335 Y-335 F1800 ; move quickly to X or Y endstop and stop there (first pass)
                                    G1 H1 X-335 ; home X axis
                                    G1 H1 Y-335 ; home Y axis
                                    G1 X5 Y5 F6000 ; go back a few mm
                                    G1 H1 X-335 F360 ; move slowly to X axis endstop once more (second pass)
                                    G1 H1 Y-335 ; then move slowly to Y axis endstop
                                    G1 H1 Z-405 F360 ; move Z down stopping at the endstop
                                    G90 ; absolute positioning
                                    G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91 ; relative positioning
                                    ;G1 Z5 F100 ; lift Z relative to current position
                                    ;G90 ; absolute positioning

                                    ; homex.g
                                    ; called to home the X axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:21 GMT-0700 (Pacific Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z5 F6000 ; lift Z relative to current position
                                    G1 H1 X-335 F1800 ; move quickly to X axis endstop and stop there (first pass)
                                    G1 X5 F6000 ; go back a few mm
                                    G1 H1 X-335 F360 ; move slowly to X axis endstop once more (second pass)
                                    G1 H2 Z-5 F6000 ; lower Z again
                                    G90 ; absolute positioning

                                    ; homey.g
                                    ; called to home the Y axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:22 GMT-0700 (Pacific Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z5 F6000 ; lift Z relative to current position
                                    G1 H1 Y-335 F1800 ; move quickly to Y axis endstop and stop there (first pass)
                                    G1 Y5 F6000 ; go back a few mm
                                    G1 H1 Y-335 F360 ; move slowly to Y axis endstop once more (second pass)
                                    G1 H2 Z-5 F6000 ; lower Z again
                                    G90 ; absolute positioning

                                    ; homez.g
                                    ; called to home the Z axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:22 GMT-0700 (Pacific Daylight Time)
                                    G91 ; relative positioning
                                    G1 H2 Z5 F6000 ; lift Z relative to current position
                                    G1 H1 Z-405 F1800 ; move Z down until the endstop is triggered
                                    G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91 ; relative positioning
                                    ;G1 Z5 F100 ; lift Z relative to current position
                                    ;G90 ; absolute positioning

                                    1 Reply Last reply Reply Quote 0
                                    • mrenz999undefined
                                      mrenz999
                                      last edited by

                                      Ok I have the motors working correctly. X and Y are homing correctly. I have z homing and the IR switch turning on (going to 1000) when activated but it doesn't stop the bed from rising when it activates.

                                      1 Reply Last reply Reply Quote 0
                                      • mrenz999undefined
                                        mrenz999
                                        last edited by

                                        Ok. Now I have all axis's homing correctly. After the Z homes it takes off
                                        to the furthest point it can from the bed ?

                                        mrenz999undefined 1 Reply Last reply Reply Quote 0
                                        • mrenz999undefined
                                          mrenz999 @mrenz999
                                          last edited by

                                          @mrenz999
                                          ; Configuration file for Duet 3 (firmware version 3)
                                          ; executed by the firmware on start-up
                                          ;
                                          ; generated by RepRapFirmware Configuration Tool v3.1.3 on Tue Jun 16 2020 08:02:01 GMT-0700 (Pacific Daylight Time)

                                          ; General preferences
                                          G90 ; send absolute coordinates...
                                          M83 ; ...but relative extruder moves
                                          M550 P"Duet 3" ; set printer name
                                          M669 K1 ; select CoreXY mode

                                          ; Drives
                                          M569 P0.0 S0 ; physical drive 0.0 goes forwards
                                          M569 P0.1 S1 ; physical drive 0.1 goes forwards
                                          M569 P0.2 S1 ; physical drive 0.2 goes backwards
                                          M569 P0.3 S1 ; physical drive 0.3 goes forwards
                                          M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
                                          M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                                          M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
                                          M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                                          M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                                          M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                                          M906 X900 Y900 Z900 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
                                          M84 S30 ; Set idle timeout

                                          ; Axis Limits
                                          M208 X0 Y0 Z0 S1 ; set axis minima
                                          M208 X330 Y330 Z400 S0 ; set axis maxima

                                          ; Endstops
                                          M574 X1 S1 P"!io0.in" ; configure active-high endstop for low end on X via pin !io0.in
                                          M574 Y1 S1 P"!io1.in" ; configure active-high endstop for low end on Y via pin !io1.in
                                          M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                                          ; Z-Probe
                                          M558 P1 C"!io3.in+io3.out" H5 F120 T6000 ; set Z probe type to modulated and the dive height + speeds
                                          M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
                                          G31 P500 X0 Y40 Z4 ; set Z probe trigger value, offset and trigger height
                                          M557 X30:260 Y20:260 S20 ; define mesh grid

                                          ; Heaters
                                          M308 S0 P"temp0" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0
                                          M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                                          M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                                          M140 H0 ; map heated bed to heater 0
                                          M143 H0 S120 ; set temperature limit for heater 0 to 120C
                                          M308 S1 P"temp1" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin temp1
                                          M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                                          M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                                          ; Fans
                                          M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
                                          M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
                                          M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
                                          M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
                                          M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
                                          M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

                                          ; Tools
                                          M563 P0 D0 H1 F0 ; define tool 0
                                          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                                          ; Custom settings are not defined

                                          ; Miscellaneous
                                          M575 P1 S1 B57600 ; enable support for PanelDue
                                          M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                                          M501

                                          New config.g

                                          ; homez.g

                                          ; called to home the Z axis
                                          ;
                                          ; generated by RepRapFirmware Configuration Tool v3.1.1 on Thu Jun 04 2020 11:20:25 GMT-0700 (Pacific Daylight Time)
                                          G91 ; relative positioning
                                          G1 H2 Z5 F6000 ; lift Z relative to current position
                                          G1 X150 Y150 F9000 ; go to first bed probe point and home Z
                                          G30 ; home z by probing the bed
                                          ; Uncomment the following lines to lift Z after probing
                                          ;G91 ; relative positioning
                                          ;G1 Z5 F100 ; lift Z relative to current position
                                          ;G90 ; absolute positioning

                                          New homez

                                          1 Reply Last reply Reply Quote 0
                                          • Phaedruxundefined
                                            Phaedrux Moderator
                                            last edited by

                                            It sounds like you've got that resolved based on your other thread.

                                            @mrenz999 said in Initial Setup With new Duet 3:

                                            @Phaedrux So looking down on the printer from above. The X motor is in the back left corner. The endstop for it is on the right side of the of the Hotend. The Y motor is in the back on the right side of the printer and the endstop for it is at the motor in the far back righthand corner of the printer.
                                            So the printer is homed at the far right back corner.

                                            This would be a flipped orientation compared to having the motors in the front, but that doesn't really matter. It's all relative to the way you are looking at it and where you want to place the coordinates. The important thing is that you have a right handed coordinate system so that it matches the way the slicer prepares the files so that you don't get mirrored parts. So be sure to test for this. It's quite possible to have things appear to be working, homing works correctly, etc, but then you go to print some text and it comes out totally backwards and upside down.

                                            If that ends up being the case check out these threads and see if they help make sense of it.

                                            https://forum.duet3d.com/topic/14971/vcore-pro-core-xy-the-x-and-y-axis-home-issue/4
                                            https://forum.duet3d.com/topic/12676/mirrored-x-axis/9

                                            Z-Bot CoreXY Build | Thingiverse Profile

                                            mrenz999undefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA