Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. mrenz999
    • Profile
    • Following 3
    • Followers 0
    • Topics 37
    • Posts 220
    • Best 4
    • Controversial 0
    • Groups 0

    mrenz999

    @mrenz999

    4
    Reputation
    6
    Profile views
    220
    Posts
    0
    Followers
    3
    Following
    Joined Last Online

    mrenz999 Unfollow Follow

    Best posts made by mrenz999

    • RE: Duet 2 or 3 for Corexy

      @MartinNYHC Take a look at this kit.
      https://www.alibaba.com/product-detail/GIULY-All-Metal-BLV-mgn-Cube_62451669742.html?spm=a2700.icbuShop.81298.1.77a7737ch3D3qc

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Duet 3 rrf 3 BLTouch

      @Phaedrux Sorry long work days. I unplugged the BLTouch on both side and plugged it back in. Hard reset and now it is working. Sorry it took so long to get back to you guys.

      posted in Duet Hardware and wiring
      mrenz999undefined
      mrenz999
    • Duet 3 Disconnects from SBC

      During printing my SBC says randomly "Network error, not connected" Then shuts down the print I have running. Not sure what is causing this.

      posted in Firmware installation
      mrenz999undefined
      mrenz999
    • RE: Independently leveled Z axis Issue

      @fcwilt makes perfect sense. I will set that. Thank You

      posted in General Discussion
      mrenz999undefined
      mrenz999

    Latest posts made by mrenz999

    • RE: Zprobe not responding

      @phaedrux
      I will make that change.
      Thank you

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Zprobe not responding

      @phaedrux
      6hc

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Zprobe not responding

      @phaedrux
      G31 P50 X16.795 Y25.4 Z.43
      Tried P8 and P5
      VCC DO AO are the three wires Red, Black, Blue in that order
      I put them on the board Red to 5v Black to Ground Blue to In.
      My assumption is the potentiometer changes the how sensitive
      it is.

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Zprobe not responding

      @mrenz999
      Also, m119 gives this respons.
      m119
      Endstops - X: not stopped, Y: not stopped, Z: not stopped, Z probe: not stopped

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Zprobe not responding

      @mrenz999
      I guess I should mention firmware 3.4b7

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • Zprobe not responding

      I am using this probe I have as a backup. Other one broke and waiting for a replacement to come.
      https://www.amazon.com/dp/B07V6GR72Q/ref=cm_sw_em_r_mt_dp_o8r7Fb4BMTP14

      Duet 3 mainboard. Connected to io 3. Hot is connected to the 5v pin, Blue wire is connected to the In pin, black connected to ground.
      M558 P5 C"io3.in" H5 F300 T6000

      I have tried with an exclamation point in front of it and without. It shows at 1000 with the exclamation point and zero without. When I
      tap it either way no changes or acknowledgement of that happening.
      Where am I going wrong ?
      lol

      Thanks

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Duet rebooting mid print

      @gloomyandy Will do. My heaters just turned off mid print. So no board reset.

      posted in Using Duet Controllers
      mrenz999undefined
      mrenz999
    • RE: Duet rebooting mid print

      @vrghost I had a similar issue. Did not reboot just stopped printing twice now. Once 3 mins in the second time 6 mins in. I checked on printer both times to find the heaters off, bed and tool, and it stopped. No errors reported just not printing.

      posted in Using Duet Controllers
      mrenz999undefined
      mrenz999
    • RE: Independently leveled Z axis Issue

      @fcwilt I will answer for me. No, my issue was never resolved.

      posted in General Discussion
      mrenz999undefined
      mrenz999
    • RE: Independently leveled Z axis Issue

      @fcwilt makes perfect sense. I will set that. Thank You

      posted in General Discussion
      mrenz999undefined
      mrenz999