Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet 3 v1.0 Fault on SD slot

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    24
    621
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator
      last edited by

      Right: https://forum.duet3d.com/topic/16191/duet3-pi-dwc-freezing/31?_=1597246408031

      All the more reason to swap it out. Something is amiss.

      Z-Bot CoreXY Build | Thingiverse Profile

      Carloundefined 1 Reply Last reply Reply Quote 0
      • Carloundefined
        Carlo @Phaedrux
        last edited by Carlo

        @Phaedrux
        April

        Thanks as always appreciate your help.

        C

        1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          It sounds like FW 3.2 beta1 is arriving shortly (maybe this week), if you still have the board when it lands, perhaps you can test it to see if it has an effect on your other SBC issue.

          Z-Bot CoreXY Build | Thingiverse Profile

          Carloundefined 1 Reply Last reply Reply Quote 0
          • Carloundefined
            Carlo @Phaedrux
            last edited by

            @Phaedrux

            E3D is out of stock so I'll keep hold until I've tested 3.2.1beta may be helpful.

            Cheers
            C

            1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator
              last edited by

              Do you happen to have a different pi to test SBC mode with?

              Z-Bot CoreXY Build | Thingiverse Profile

              Carloundefined 1 Reply Last reply Reply Quote 0
              • Carloundefined
                Carlo @Phaedrux
                last edited by

                @Phaedrux

                Yeah tested it with 3 Pi's 2x 4b and 1 3b+ all exactly the same result with nothing else attached and even tried a new 26 pin cable still the same.

                Carloundefined 1 Reply Last reply Reply Quote 0
                • Carloundefined
                  Carlo @Carlo
                  last edited by

                  @Carlo
                  The freezing I sorted by not using duetPi and just adding DSF to another distro but thats a far as I could get I could do everything but print ..just went nuts on the purge line or first move
                  actually damaged my print bite sheet rammed the head in to the bed bent the heat break
                  but same files Iv'e printed many time in stand alone

                  1 Reply Last reply Reply Quote 0
                  • A Former User?
                    A Former User
                    last edited by

                    i didn't read the whole thread i'll admitt, but if you want to verify the individual parts that make up the connection between the pi and the duet this old-ish thread has a ton of information on where to go digging https://forum.duet3d.com/topic/15551/duet3-pi-dcs-is-unavailable-after-wiring-24v/119?_=1597267914698

                    (and if not, disregard:)

                    Carloundefined 1 Reply Last reply Reply Quote 1
                    • Carloundefined
                      Carlo @A Former User
                      last edited by

                      @bearer

                      Thanks bearer I was following the thread at the time I did check continuity and chris did manage to recreate an issue I was having so expect there would be a fix at some point
                      though at the time it was still freezing my issues which are many but with the duet even weirder and may not have been software or communication between the 2 as it ran as expected until a file was loaded everything else perfect probe, mesh G1's all extruding, heaters maybe a buffer/memory conflict/issue ?

                      droftartsundefined 1 Reply Last reply Reply Quote 0
                      • droftartsundefined
                        droftarts administrators @Carlo
                        last edited by

                        @Carlo These two pins of your SD card socket do not look well soldered:
                        Screenshot 2020-08-13 at 14.50.20.png
                        Can you take a picture of the socket from an angle across the board, as shown here https://duet3d.dozuki.com/Wiki/SD_Card#Section_SD_Card_Socket

                        Ian

                        Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                        Carloundefined 1 Reply Last reply Reply Quote 0
                        • Carloundefined
                          Carlo @droftarts
                          last edited by Carlo

                          @droftarts

                          Hi Ian,

                          Sorry the board went in the mail run today wanted to keep it a while to test 3.2 beta 1
                          plus it is out of stock...but you get 7 days for return once they issue a returns # and I may have no access to office or workshop due to another possible 2 week lock down in my area

                          all the pins looked to be well attached and no oxidation all the contacts look ok..bit hard to see inside the slot

                          Image I took yesterday from a different angle.

                          IMG_1618.jpg

                          Dunno if it is of help.

                          Cheers
                          C

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA