BL-Touch and problems

BoA

"Origin at center" in cura(or some other slicer You are using) machine settings perhaps ?

Or....

G10 P0 X45 Y0 Z0

Why Do You have tool offset 45mm for X axis ??

Phaedrux

"Origin at center" in cura(or some other slicer You are using) machine settings perhaps ?

Or....

G10 P0 X45 Y0 Z0

Why Do You have tool offset 45mm for X axis ??

bingo!

n3ovo

@Veti yes it moves just what it should

thanks

n3ovo

Ok i removed all the Commands from cura. did not help ,, cant find out why, I started and old laptop with cura with the same out come and this ran before with no problem. Yes i changed it to RepRap did not help ... told cura to print in the centre of bed, Still no good same outcome ...

went tonight and got PrusaSlicer ran the same g-code that i have been trying and no good // still printer off one side???

I am thinking i have a bad update to the ROM/Web
2 things someone let me know i am running 3.1.1 but i have It seems A Log more in there and i needed. Here is a list of files i have in the 0/sys/ folder?

duet3d_FTP_2020-09-08 03-03-07.png

And What files do i need to Download, I am i little confused of what to download to make sure i have a good copy!

Thanks John G.

n3ovo

@Phaedrux

The reason for the BIG number we still playing around and i just keep it there till o get around to getting the HOLE bed to print from .. my still big problem is that it is still only printing on the left side

thanks John G

droftarts

@n3ovo your first tool should have no XYZ offset. Everything else is referenced from the first tool. You’re not going to be able to print to the whole bed with that offset. Set it to zero.

Ian

Phaedrux

@n3ovo said in BL-Touch and problems:

And What files do i need to Download, I am i little confused of what to download to make sure i have a good copy!

Download it all.

@n3ovo said in BL-Touch and problems:

told cura to print in the centre of bed, Still no good same outcome ...

No you don't want cura to use a center origin. "Origin at center" should be unchecked.

Your problem is the tool offset of X45, unless you have a specific reason for that?

n3ovo

Hello All I Am Back with some small problems that i sure could us some help ..

So one problem, is the fan i must have it switch and when i run the job the cooling fan does not start on it own. It works with "FAN 0" i just turned it on now and it works. Have my Config.g below...

Another one is i added this the picture below started printing and had to babby step - 0.520mm to get it printing right seems good now would i adjust the

G31 P45 X25 Y25 Z2.270 ; Z probe trigger value,

in the config file to see the right z-height

Thanks as Allways .... John G. N3OVO

; General preferences
M29 S0                                         ; Load height map from file, activate bed compensation default name 0:/sys/heightmap.csv
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"CR10s_Pro"                              ; set printer name
M918 P1 E4 F2000000                            ; configure direct-connect display

; Network
M551 P"n3ovo3"                                 ; set password
M552 P192.168.1.66 S1                          ; enable network and set IP address 
M553 P255.255.255.0                            ; set netmask
M554 P192.168.1.1                              ; set gateway
M586 P0 S1                                     ; enable HTTP
M586 P1 S1                                     ; enable FTP
M586 P2 S1                                     ; enable Telnet  

; Drives
M569 P0 S0                                     ; physical drive 0 goes backwards 
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S0                                     ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E136.00              ; set steps per mm started at 93
M566 X1200.00 Y1200.00 Z24.00 E300.00          ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00          ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I50                  ; set motor currents (mA) and motor idle factor in per cent
M84 S100                                       ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S 1                              ; set axis minima
M208 X300 Y300 Z400 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z

; Z-Probe 
; BLTouch - via exp.heater7
M558 P9 C"^zprobe.in" H4 R0.2 F1000 T4000      ; Set Z probe type/mode 9. H=Dive Height. F=Speed the bed 
M950 S0 C"exp.heater7"                         ;
G31 P45 X25 Y25 Z2.270                        ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
M557 X55:300 Y50:300 S16:16
;M557 X55:290 Y25:290 P6S:16                     ; Define mesh grid
 
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M140 H0                                        ; map heated bed to heater 0
M143 H0 S150                                   ; set temperature limit for heater 0 to 150C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q600                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1                                 ; set fan 1 value. Thermostatic control is turned off
M950 F2 C"fan2" Q500                           ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45                            ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                  ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets was 45
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M591 D0 C3 P1 E1 S1				               ; Turn on functionality for a filament run-out switch

; Miscellaneous
M575 P1 S1 B57600                              ; enable support for PanelDue
M501                                           ; M501: Read all stored parameters
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Phaedrux

@n3ovo said in BL-Touch and problems:

the fan i must have it switch and when i run the job the cooling fan does not start on it own. It works with "FAN 0" i just turned it on now and it works.

I'm not really sure what you mean with this.

What do you have connected to fan port 0 and 1? Are those meant to both be part cooling fans? Are they supposed to both work together?

Is Fan port 2 for your hotend heatsink fan?

For the baby stepping, if you want to make that adjustment permanent, add the value to your G31 Z.

G31 P45 X25 Y25 Z2.270 would become G31 P45 X25 Y25 Z2.790

kareka

This post is deleted!

jay_s_uk

@kareka please start your own thread