DWC 3.1.1
-
H1 NON VA SI BLOCCA NON SI SINTONIZZA
COMADO M307 H 1 ECCO LETTURA
M307 H 1
Heater 1 model: heating rate 2.429, cooling time constant 140.0, dead time 5.50, max PWM 1.00, calibration voltage 0.0, mode PID
Computed PID parameters: setpoint change: P13.4, I0.482, D51.4, load change: P13.4, I0.949, D51.4ESEGUO AUTOMATICO
M303 H1 S
Auto tuning heater 1 using target temperature 0.0°C and PWM 1.00 - do not leave printer unattendedNON SI FERMA IL PROCEDIMENTO HEATER 1 OSCILLA TRA 23,4 23,8
POI M0
-
I'm not sure what you're saying. The translation was not very good this time.
THE PROCEDURE DOES NOT STOP HEATER 1 SWINGS BETWEEN 23.4 23.8
PID tuning can take a long time.
-
ESATTO , 20 30 MINUTI PER UN RISCALDATORE , H1 LAVORA PER 60 MINUTI O PIU' . IN TUTTE LE CALIBRAZIONE CHE HO FATTO, LA TEMPERATURA SALIVA AL MASSIMO .
ORA LA TEMPERATURA VA MASSIMO A 24 GRADI MI STUPISCO . ORA STA LAVORANDO
-
M303 H1 S
You need to set a temperature after the S
M303 H1 S200
-
AVEVO CAPITO HE S NON IMPOSTATO ANDAVA ALLA MASSIMA TEMPERATURA .GRAZIE PROVO SUBITO
-
This post is deleted! -
@Phaedrux PERFETTO
GRAZIE -
NON HO CAPITO . HO FATTO G 29 LA MACCHINA HA LAVORATO MA NIENTE GRAFIGO RAPPRESENTATO COME SI VEDE. UNA VOLTA HA FATTO GRAFICO CON UN G 29 POI NON PIU'
gives me this error Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)
It sounds like you are missing a ; to commend out that line?
NON COMPRENDO SCUSA
-
-
MI HA MANDATO QUI NON SO SE HA IMPORTANA PENSO RIGUARDI LO SPESSORE E IL MATERIALE, DEVO CREARE UN FILE
-
Create a folder on your SD card called
menuand another calledfilamentsConfiguration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)Check your config files for that line. Some where there is a file that has that line and it's missing a
;at the start to mark it as a comment. -
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)
; IN GONFIG.G OK
Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)
Check your config files for that line. Some where there is a file that has that line and it's missing a ; at the start to mark it as a comment.
-
What are you doing when that error message shows up?
-
HO FATTO MENU FILAMENT IN SD CARD
-
ECCO -
SE TOCCO PIANO-SONDATO .CSV SI BLOCCA TUUO.
-
This post is deleted! -
DA L ERRORE QUANDO ARRIVA SUL PIATTO ED ESTRAE LA SONDA HO UN BBLTouch
-
Please post all your config files. config.g homeall.g homex.g homey.g homez.g homedelta.g bed.g deployprobe.g retractprobe.g
-
