Pinda prob config

danny777

This is what i get

Phaedrux

Have you power cycled your board recently? I can't really tell what's going on from your screen shot as it doesn't appear to be updating the text.

danny777

Yes I work with the machine ,

danny777

It looks like lots of details thet i run throough the dwc showes on the console,
for exemple , when I run mesh compensation i get this

Phaedrux

Are you using a raspberry pi with your Duet?

If you look at the general tab in DWC and the machine specific tab what versions are listed for the Duet and DWC?

danny777

Im not using a raspberry pi
version - Duet Web Control 3.1.1

Phaedrux

Ok, if DWC is on 3.1.1 then I wonder what your firmware version is. Something isn't matched up.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/Duet2and3Firmware-3.3.zip

Upload this zip file as it is to the system tab in DWC, don't extract it first. After it is finished update the firmware and reboot. Then send M122 again and see what it reports.

danny777

Did it! look better but still "error; invalid use of p parameter"
03ce6d49-eec4-4e3f-a336-bdd208f1043a-image.png

Phaedrux

Can you send M98 P"config.g" again now?

danny777

here

danny777

Now after update firmwere ,I have a new problem, if push z 5 mm up it moves down
and not all the time , once is up and once it down , same button

danny777

Sent m122 again , attached
console.txt

Phaedrux

The first error "bad command: M" is from the very first line in your config.g. there is an M at the start of the line.

M; Configuration file for Duet 3 (firmware version 3)

The invalid P may be from your fan definitions

; Fans
M950 F0 C"out5" Q500                         ; create fan 0 on pin out7 and set its frequency
M106 P0 S0 H-1                               ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out4" Q500                         ; create fan 1 on pin out8 and set its frequency
M106 P0 S1 H1 T45                            ; set fan 1 value. Thermostatic control is turned on ; set fan 1 value. Thermostatic control is turned on

You have P0 twice. The second P0 should be P1.

@danny777 said in Pinda prob config:

if push z 5 mm up it moves down
and not all the time , once is up and once it down , same button

Which button exactly are you pushing?

danny777

This one, first tap and secont tap the head go -0.5 then third or four tap the head go up 5mm,

@phaedrux

danny777

This post is deleted!

danny777

M122
console (1).txt

Phaedrux

It sounds like you might just need to calibrate the touch areas on the panel. Also try using a finger nail to press.

Have you updated the firmware on the PanelDue yet? You can see the version in the setup page.

https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update#Section_Firmware_update_via_USB

danny777

Ohh,
Im trying to udate, via dwc, its uploading the files , but when I press yes for install its say no sistem files

Phaedrux

@danny777 said in Pinda prob config:

Im trying to udate, via dwc, its uploading the files , but when I press yes for install its say no sistem files

Depending on the version of paneldue firmware currently installed on the paneldue it may not work via DWC. I suggest you update via USB first to version 3.3

danny777

with bossa
?