I could use some help

[droftarts]

@mac I think, for clarity, can you post your current config.g, homeall.g, homex.g, homey.g and homez.g please?

Ian

[A Former User]

@droftarts I remember buying GTS belts for my BLV-Anet, so that’s exactly what it is. I replaced the oem belt on this XVico about two weeks ago.

[A Former User]

@droftarts

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Frankenstein's Cinderella"                  ; set printer name

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
M569 P0.1 S0                                       ; physical drive 0.1 goes backwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S1                                       ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X100.000 Y100.00 Z4000.00 E420.00                 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E250.00               ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600                           ; set motor currents (mA)
M84 S0                                             ; Disable motor idle current reduction

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X220 Y220 Z240 S0                             ; set axis maxima

; Endstops
M574 X2 S1 P"!^io5.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !^io5.in
M574 Y2 S1 P"!^io6.in"							   ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !^io6.in
M574 Z2 S1 P"!^io2.in"							   ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin !^io2.in							   

; Z-Probe
M950 S0 C"io3.out"                                 ; create servo pin 0 for BLTouch
M558 P9 C"io3.in" H5 F120 T3600                    ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X15.875 Y0.625 Z2.5                       ; set Z probe trigger value, offset and trigger height
M557 X5:190 Y5:215 S10                             ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4092       ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S33                                        ; set temperature limit for heater 0 to 33C
M308 S1 P"temp1" Y"thermistor" T100000 B4092       ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S100                                       ; set temperature limit for heater 1 to 100C

; Fans
M950 F0 C"out3" Q500                               ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out4" Q500                               ; create fan 1 on pin out4 and set its frequency
M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"optional" D0 H1 F0                       ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
M98 P"homeZ.g"
M98 P"homeX.g"
M98 P"homeY.g"

; Uncomment the following lines to lift Z after probing
;G91                  ; relative positioning
;G1 Z5 F60            ; lift Z relative to current position
;G90                  ; absolute positioning

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
G91
G1 H1 X-230 F3600
G1 X15
G1 H1 X-10 F360
 
G90
G1 X110 F3600 ; this just moves X to the centerline of the bed - doesn't matter where - it can be any place at all that suits you.

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
G91
G1 H1 Y-230 F3600
G1 Y15
G1 H1 Y-10 F360
 
G90
G1 Y110 F3600 ; this just moves Y to the centerline of the bed - doesn't matter where - it can be any place at all that suits you.

homez.g

G91               ; relative movements
G1 H1 Z-250 F3600 ; fast move toward Z endstop
G1 Z10            ; backup off a bit
G1 H1 Z-15 F360   ; slow move toward Z endstop
 
G90               ; absolute movements
G1 Z10 F3600      ; move to 10mm off the bed to allow X and Y movements

The above is current on 6-28-22 at 7:15 AM, PST.

[droftarts]

@mac what is currently working, and not working? Maybe go through the commissioning guide. If something doesn’t work, make a note and move on to the next.
https://docs.duet3d.com/en/How_to_guides/Commissioning

Ian

[fcwilt]

@mac

Morning.

Now that we know the end-to-end travel of the Y axis is some 350mm you need to edit the homeY.g file.

Notice the G1 H1 X-230 command.

That is not moving enough to move the entire 350mm if it needs to.

So change the -230 to -360, save, re-boot and re-home Y to see if it moves to the Y endstop twice and then back to near the center of the bed.

If that all works then we can proceed to figure out what is wrong with the X stepper.

I await the results of the Y homing test.

Frederick

[A Former User]

@droftarts @fcwilt @alankilian

Here's what we learned last night:

The Y-axis / bed can roll all the way to the rear edge of the pulley. That's where I placed the beginning of my metal ruler. You can hear the bed activate the endstop when it gets to the rear side of the spindle that goes through the pulley. Moving the bed back creates that beautiful second click that indicates the message has been sent, and the bed is backing away from the endstop.

When the bed is all the way to 0 on the metal ruler, which goes back to front of the printer, the endstop is fully depressed. When the rear edge of the bed is at the center of the Y-pulley spindle, it is contacting the endstop, and when it is at the rear of the spindle, the endstop is fully activated, but not fully depressed. Those events happen between 0 and 12.75mm's (rear to front).

Pushing the bed as far to the rear as it can go takes it to -.238mm's (to the rear of 0).

Pushing the bed to the front of the printer takes it to 457.2mm's. DWC reports that the bed is at 350.0mm's.

Pushing the bed to 247.65mm's puts the rear line of the bed directly under the nozzle.

Pushing the bed to 25.4mm's puts the rear line of the bed over the front of the Y-motor. At that point, the front line of the bed is under the nozzle.

Important: The foot that pushes against the Y-endstop is still 73mm's in front of it. This means that the bed has to go another 73mm's to the rear to contact the endstop. It also means that the bed is 15.875mm's to the rear of the nozzle.

So this is what we need to communicate to the firmware, I gather, so that it can move the bed accordingly.
Any help getting there would be appreciated.

Mac

[fcwilt]

@mac

It should not be possible to move the bed left and right.

It should only move forward and back.

I'm confused by what you posted.

Thanks.

Frederick

P.S. Don't forget the required change to homeY.g and the testing thereof.

[A Former User]

@fcwilt I just posted the measurements I've been collecting over the last four hours. Maybe they will be helpful? Maybe they will have some impact on what I just read in your post? I'm all for moving forwards, but it's nice to know the route ahead beforehand?

[A Former User]

@fcwilt understandable, because I have the printer sideways so I can read the metal tape measure. I'll edit the post.

[fcwilt]

@mac said in I could use some help:

@fcwilt understandable, because I have the printer sideways so I can read the metal tape measure. I'll edit the post.

OK I understand what you were describing now.

Frederick

[fcwilt]

@mac said in I could use some help:

@fcwilt I just posted the measurements I've been collecting over the last four hours. Maybe they will be helpful? Maybe they will have some impact on what I just read in your post? I'm all for moving forwards, but it's nice to know the route ahead beforehand?

My first goal today is to get the Y axis working in all regards.

We have gotten it moving in the right directions.

We have determined how far it can travel.

Now we need to get Y homing working.

Once that is done we need to move on to getting the X axis working, then the Z axis.

It is essential that all three axes work correctly and home correctly before we can move on to the next phase.

Frederick

[A Former User]

@fcwilt essential work sounds like fun! I'm all in.

[A Former User]

@droftarts thanks for asking, Ian. I'm going to focus all of my attention of meeting Frederick's needs today, as he's hell-bent to get my printer working properly. I feel like I need to support his efforts as best I can.

At some point, I'll make a video about all of this, and put what I've learned about the technology and the coding and the great customer support I've received. Hopefully, I'll be able to use moving pictures to make the points that need to be made.

Mac

[A Former User]

@fcwilt I'm going to make the change, etc., and will let you know as quickly as I can.

[fcwilt]

@mac said in I could use some help:

@droftarts thanks for asking, Ian. I'm going to focus all of my attention of meeting Frederick's needs today, as he's hell-bent to get my printer working properly. I feel like I need to support his efforts as best I can.

At some point, I'll make a video about all of this, and put what I've learned about the technology and the coding and the great customer support I've received. Hopefully, I'll be able to use moving pictures to make the points that need to be made.

Mac

I assume you want to get it working as well?

If that is not the case then let me know and we can explore any aspect of your printer you like.

Frederick

[droftarts]

@mac once the axes are moving correctly, it may help you to draw a picture of the bed. Measure the size of the bed. Move the nozzle to the home X and Y position, touching the endstops. Is the nozzle over the bed, on the edge of the bed, or not over the bed? Measure the offsets. Do the same with the nozzle at the maximum position, measuring the offsets from the bed. You will need these numbers for the M208 commands, to get the printer to know where the printable are of the bed is.

Ian

[A Former User]

@fcwilt REPORT: the bed started towards the rear of the printer slowly, then moved faster, until it came to where it thought it should stop, and did so.

UPDATE: I decided to move the bed forwards as far as it would go. DWC is telling me that the bed will go to 220mm. According to my metal measuring stick, 220mm is 327mm in the real world.

UPDATE: I thought I was seeing weird behavior. So I moved the bed forwards and backwards to the limits imposed on it by the firmware. A couple of times I hit the endstop and then kept going to pound on the motor a bit. None of this bothers me. I have a box of endstops and a box of motors I can use to repair whatever damage these efforts produce.

The firmware is limiting how far the bed can go forwards to where it thinks 220mm is. It's 220mm is 327mm in the real world.

It's not lightly touching the end-stop, then backing up (forwards) / away from it.

M119 reports that Y is at Max Endstop.

[A Former User]

@fcwilt "properly" means exactly that.

I'll put it another way: I want this $160+ dollar board to outperform the mystery board in my Xvico. I think my efforts, and everyone's help require that to put the world right again.

Mac

[A Former User]

@droftarts I understand. And I'm working on developing that image.

[A Former User]

@fcwilt I just ran M119 for all 3 endstops. When depressed, all of them are reporting that they are at Max Endstop.