Reboots/crashes - RRF ≤3.5.0-rc1

[T3P3Tony]

@NeoDue thanks for this information. We need the M122 report(s) for when the Duet crashes. The DWC not recovering from sleep modes etc may be related but may also be a different issue so lets leave that aside for now and focus on what happens when RRF crashes.

[NeoDue]

@T3P3Tony @Exerqtor okay. Just to be sure: This means I let the Duet crash and get an M122 afterwards. Anything I need to set on the Duet in advance?

[T3P3Tony]

@NeoDue It does not hurt to grab a M122 before you start but nothing specifically in advance.

[Exerqtor]

Just got back home from work, to another crash on 1.27.

Besides crashing (seemingly just as often as the 2.4 betas), DWC loads sooooo damned slow with 1.27!

Anywho, another report:

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 14 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122016 of which 0 recycled
Never used RAM 13700, free system stack 182 words
Tasks: NETWORK(2,nWait,23.4%,211) HEAT(3,nWait,0.0%,352) Move(4,nWait,0.0%,358) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,nWait,0.7%,108) MAIN(1,running,69.4%,670) IDLE(0,ready,5.6%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:18:49 ago, cause: software
Last software reset at 2023-12-14 15:39, reason: AssertionFailed, Gcodes spinning, available RAM 13676, slot 1
Software reset code 0x4123 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00489000 BFAR 0xe000ed38 SP 0x20011fbc Task NETW Freestk 495 ok
Stack: 00000919 000af3d0 0002de6f 2002bed4 2002be01 000001af 2002c168 20031ca0 2002c180 2001e888 a5a5a5a5 0d0a0d36 0d312e30 00000000 00000000 00000000 20031cac 00000800 200359a0 2002c168 20018678 2002bf9d 20018678 2001e888 0003010f 00000000 00000000
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 1129622, completed 1129621, timed out 0, errs 0
MCU temperature: min 34.8, current 35.3, max 38.2
Supply voltage: min 21.7, current 24.1, max 27.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/22, heap memory allocated/used/recyclable 2048/1604/1304, gc cycles 2081
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 16, read errors 0, write errors 1, ifcnt 177, reads 59429, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 208, read errors 0, write errors 1, ifcnt 175, reads 59429, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 2, read errors 0, write errors 1, ifcnt 19, reads 59429, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 1, ifcnt 21, reads 59428, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 2, read errors 0, write errors 1, ifcnt 15, reads 59429, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-14 15:57:58
Cache data hit count 1957951974
Slowest loop: 13.50ms; fastest: 0.13ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 7.8ms, write time 4.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 10177, received 23198, lost 0, errs 1, boc 0
Longest wait 2ms for reply type 6031, peak Tx sync delay 261, free buffers 26 (min 25), ts 5649/5648/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 12.58ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 4 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 1.27
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 25624
WiFi IP address 192.168.10.x
Signal strength -54dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

[timschneider]

@dc42
I was looking at the code and found your ocmment about the failed assert.

// Look at the response
#if SAME5x	//TEMP DEBUG
	CheckStackValue(9, ra);			//***** This is the check that occasionally fails ******
#endif

looking backwards from here it will reset the spi and disable the dma channel. There is a comment about the disabling of the dma channel on SAME5x.

// Disable a channel. Also clears its status and disables its interrupts.
// On the SAME5x it is sometimes impossible to disable a channel. So we now return true if disabling it succeeded, false it it is still enabled.
bool DmacManager::DisableChannel(const uint8_t channel) noexcept
{

but the return value is not checked in the function:

static inline void spi_rx_dma_disable() noexcept

From here I've looked in the datasheet of the chip to check the dma function and found the following:

So it is possible that a DMA transfer is already scheduled but not processed and this will block/prevent the gracefull disable from taking place.

[Exerqtor]

@timschneider said in Reboots/crashes - RRF 3.5.0-rc1:

@dc42
I was looking at the code and found your ocmment about the failed assert.

// Look at the response
#if SAME5x	//TEMP DEBUG
	CheckStackValue(9, ra);			//***** This is the check that occasionally fails ******
#endif

looking backwards from here it will reset the spi and disable the dma channel. There is a comment about the disabling of the dma channel on SAME5x.

// Disable a channel. Also clears its status and disables its interrupts.
// On the SAME5x it is sometimes impossible to disable a channel. So we now return true if disabling it succeeded, false it it is still enabled.
bool DmacManager::DisableChannel(const uint8_t channel) noexcept
{

but the return value is not checked in the function:

static inline void spi_rx_dma_disable() noexcept

From here I've looked in the datasheet of the chip to check the dma function and found the following:

So it is possible that a DMA transfer is already scheduled but not processed and this will block/prevent the gracefull disable from taking place.

Woah, great catch! Hope you're on to something there!

---

And some more data points:

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122016 of which 0 recycled
Never used RAM 13700, free system stack 186 words
Tasks: NETWORK(1,ready,23.2%,217) HEAT(3,nWait,0.0%,335) Move(4,nWait,0.0%,344) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,delaying,0.7%,108) MAIN(1,running,69.6%,670) IDLE(0,ready,5.5%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:25:42 ago, cause: software
Last software reset at 2023-12-14 20:16, reason: AssertionFailed, Expansion spinning, available RAM 13676, slot 2
Software reset code 0x4132 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x20011fbc Task NETW Freestk 495 ok
Stack: 00000919 000af3d0 0002de6f 2002bed4 2002be01 000001af 2002c100 20031458 2002c118 2001e888 a5a5a5a5 a5a5a5a5 0d312e30 00000000 00000000 00000000 20031464 00000800 20035970 2002c100 20018678 2002bf9d 20018678 2001e888 0003010f 00000000 00000000
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 1542150, completed 1542150, timed out 0, errs 0
MCU temperature: min 35.3, current 35.9, max 38.6
Supply voltage: min 21.9, current 24.1, max 27.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/23, heap memory allocated/used/recyclable 2048/2048/1736, gc cycles 2851
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 16, read errors 0, write errors 1, ifcnt 191, reads 15599, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 208, read errors 0, write errors 1, ifcnt 189, reads 15599, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 2, read errors 0, write errors 1, ifcnt 33, reads 15598, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 1, ifcnt 35, reads 15598, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 2, read errors 0, write errors 1, ifcnt 29, reads 15599, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-14 20:42:33
Cache data hit count 2670623150
Slowest loop: 11.30ms; fastest: 0.13ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 8.4ms, write time 3.6ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is doing "G4 P10" in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 13889, received 31654, lost 0, errs 1, boc 0
Longest wait 2ms for reply type 6031, peak Tx sync delay 300, free buffers 26 (min 25), ts 7711/7710/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 13.57ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 4 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 1.27
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 25624
WiFi IP address 192.168.10.x
Signal strength -53dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

[NeoDue]

@T3P3Tony thanks! Test is running now. One thing I found due to the browser updating itself soon after start: when the browser was closed for update with Duet tabs open, there is a brief "incomplete transfer" message on the PanelDue - and then the Duet resets the wifi connection (3.5.0rc1 with wifi module firmware 2.1b6 - at least reconnection seems reliable now with that firmware version). After that, one of the Duet tabs was dead. The only thing that differed in the log was the amount of reconnections.

I will ignore that for now as you suggested and wait for a crash to happen. The printer is set to write an m122 log into a file afer every reboot - let's see what I find tomorrow.

[Exerqtor]

@NeoDue
Looking forrward to seeing how this turns out for you, and if we have the same root cause for the crashes!

---

Other than that i'm moving over to WiFiServer 2.1b4 again, 1.27 is pretty much useless at this point. It flip out on reboot/crash and won't connect to the LAN with the only means i've found to connect it when that happens is to power toggle the printer til it manages to connect. And once it's finally able to connect, connecting to the printer/DWC is a total shitstorm, 90% of the times it just yields a white/blank screen. And once you're finally able to get a connection it's soooooo slow.

Here is the last crash report from 1.27 and a snipet from the debug log so you can see how it behaves when not being able to connect to the LAN (attached as a mega.nz file since it's a shit ton of data).

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122100 of which 0 recycled
Never used RAM 13616, free system stack 186 words
Tasks: NETWORK(1,ready,23.6%,203) HEAT(3,nWait,0.0%,354) Move(4,nWait,0.0%,358) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,341) TMC(4,nWait,0.7%,114) MAIN(1,running,69.1%,670) IDLE(0,ready,5.7%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:07:20 ago, cause: power up
Last software reset at 2023-12-14 23:02, reason: AssertionFailed, none spinning, available RAM 13700, slot 0
Software reset code 0x4133 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x20011fbc Task NETW Freestk 495 ok
Stack: 00000919 000af3d0 0002de6f 2002bed4 2002be01 000001af 2002c100 20031488 2002c118 2001e888 a5a5a5a5 a5a5a5a5 0d312e30 00000000 00000000 00000000 20031494 00000800 200359a0 2002c100 20018678 2002bf9d 20018678 2001e888 0003010f 00000000 00000000
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 440375, completed 440375, timed out 0, errs 0
MCU temperature: min 34.0, current 35.3, max 37.1
Supply voltage: min 0.9, current 24.0, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/23, heap memory allocated/used/recyclable 2048/1516/1204, gc cycles 801
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 23148, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 23148, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 23148, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 23147, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 13, reads 23148, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-15 07:56:22
Cache data hit count 764831191
Slowest loop: 10.98ms; fastest: 0.13ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 7.8ms, write time 4.4ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is doing "G4 P10" in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 3974, received 9009, lost 0, errs 1638, boc 0
Longest wait 2ms for reply type 6053, peak Tx sync delay 11121, free buffers 26 (min 25), ts 2202/2200/0
Tx timeouts 0,0,1,0,0,0 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 14.24ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 3 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 1.27
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 25536
WiFi IP address 192.168.10.x
Signal strength -54dBm, channel 0, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

The debug log file.

[NeoDue]

@Exerqtor so far no crashes here. They happened less often than they seemed to do at your place, so I will leave the test running.

I would however suggest you try to switch to Wifi firmware 2.1b6 instead of b4 - apart from debugging my config and macro files, that was the only thing I did with my printer since RC1 came out, and at least for me, that one solved some issues (albeit seemingly unrelated ones, but who knows...)

[Exerqtor]

@NeoDue said in Reboots/crashes - RRF 3.5.0-rc1:

@Exerqtor so far no crashes here. They happened less often than they seemed to do at your place, so I will leave the test running.

That's good to hear, on your behalf i mean

I would however suggest you try to switch to Wifi firmware 2.1b6 instead of b4 - apart from debugging my config and macro files, that was the only thing I did with my printer since RC1 came out, and at least for me, that one solved some issues (albeit seemingly unrelated ones, but who knows...)

Oh is there a 2.1b6? And where is that bugger hiding out?

---

Otherwise it's been two crashes while on 2.1b4, and here is a report:

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122016 of which 0 recycled
Never used RAM 13700, free system stack 180 words
Tasks: NETWORK(1,ready,57.1%,228) HEAT(3,nWait,0.1%,335) Move(4,nWait,0.0%,344) CanReceiv(6,nWait,0.1%,774) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,nWait,1.8%,108) MAIN(1,running,25.2%,670) IDLE(0,ready,13.5%,29) AIN(4,delaying,2.1%,264), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 02:37:51 ago, cause: software
Last software reset at 2023-12-15 11:37, reason: AssertionFailed, none spinning, available RAM 12492, slot 2
Software reset code 0x4133 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x20011fbc Task NETW Freestk 495 ok
Stack: 00000919 000af3d0 0002de6f 2002bed4 2002be01 000001b0 2002c100 20031c88 2002c118 2001e888 a5a5a5a5 a5a5a5a5 312e303d 00000000 00000000 00000000 20031c94 00000800 20035988 2002c100 20018678 2002bf9d 20018678 2001e888 0003010f 00000000 00000000
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 9471453, completed 9471453, timed out 0, errs 0
MCU temperature: min 34.7, current 35.3, max 37.8
Supply voltage: min 22.5, current 24.1, max 26.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/22, heap memory allocated/used/recyclable 2048/1376/1076, gc cycles 17933
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 16, read errors 0, write errors 1, ifcnt 58, reads 39703, writes 13, timeouts 1, DMA errors 0, CC errors 0, failedOp 0x72
Driver 1: standstill, SG min 16, read errors 0, write errors 1, ifcnt 58, reads 39704, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 1, ifcnt 46, reads 39704, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 1, ifcnt 47, reads 39703, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 1, ifcnt 46, reads 39704, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-15 14:15:14
Cache data hit count 4294967295
Slowest loop: 13.44ms; fastest: 0.13ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 7.7ms, write time 4.4ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 85250, received 194199, lost 0, errs 1, boc 0
Longest wait 2ms for reply type 6053, peak Tx sync delay 273, free buffers 26 (min 25), ts 47356/47355/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 7.31ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 3 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1beta4
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 42948
WiFi IP address 192.168.10.x
Signal strength -52dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0

[dc42]

@NeoDue said in Reboots/crashes - RRF 3.5.0-rc1:

Duet crashes occur (on a Duet 3 6HC running RRF 3.5.0 beta 4 or 3.5.0rc1)

Is this when using the optional WiFi module for the 6HC, or using Ethernet? Do you have any M122 reports from the 6HC taken after the Duet has reset?

[NeoDue]

@dc42 That was all with the optional Wifi module active, I used that one from the very start with the 3 6HC.
Sorry, but I did not keep any M122 logs of that since I did not make the connection you and Exerqtor dug out here and simply thought: "random crashs... well, still beta - the Duet team will surely work an that already - and until you can find some trigger, there is no use in reporting anything".

@Exerqtor beta 6 is in the corresponding Github archive from the Duet team: https://github.com/Duet3D/WiFiSocketServerRTOS/releases

[Exerqtor]

@NeoDue said in Reboots/crashes - RRF 3.5.0-rc1:

@dc42 That was all with the optional Wifi module active, I used that one from the very start with the 3 6HC.
Sorry, but I did not keep any M122 logs of that since I did not make the connection you and Exerqtor dug out here and simply thought: "random crashs... well, still beta - the Duet team will surely work an that already - and until you can find some trigger, there is no use in reporting anything".

@Exerqtor beta 6 is in the corresponding Github archive from the Duet team: https://github.com/Duet3D/WiFiSocketServerRTOS/releases

Well there you go, thx! Installed it now, so lets see if that makes an difference 🤷‍♂️

---

And one last "M122" from 2.1b4:

M122
15.12.2023, 16:57:34	=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122016 of which 0 recycled
Never used RAM 13700, free system stack 184 words
Tasks: NETWORK(1,ready,24.6%,227) HEAT(3,nWait,0.0%,352) Move(4,nWait,0.0%,358) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,nWait,0.7%,108) MAIN(1,running,67.6%,670) IDLE(0,ready,6.1%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:24:30 ago, cause: software
Last software reset at 2023-12-15 16:33, reason: HardFault bfarValid precise, Platform spinning, available RAM 13676, slot 0
Software reset code 0x4060 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x312e303d SP 0x20011f60 Task NETW Freestk 472 ok
Stack: 312e303d 20032cad 00000047 312e303c 20032e6c 0002dd7f 00004434 210f0000 0002dd27 2002bed4 2002be01 000001c0 2002c138 20031c70 2002c150 2001e888 a5a5a5a5 a5a5a5a5 0002ff75 00000000 00000000 00000000 312e303d 00000800 20034fa0 2002c138 20018678
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 1470513, completed 1470512, timed out 0, errs 0
MCU temperature: min 35.9, current 36.2, max 36.3
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/23, heap memory allocated/used/recyclable 2048/1496/1184, gc cycles 2757
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 16, read errors 0, write errors 0, ifcnt 72, reads 314, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 16, read errors 0, write errors 0, ifcnt 72, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 0, ifcnt 60, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 61, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 60, reads 314, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-15 16:57:46
Cache data hit count 2535039282
Slowest loop: 6.44ms; fastest: 0.15ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 4.0ms, write time 1.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 54, received 123, lost 0, errs 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 6, free buffers 26 (min 26), ts 30/30/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 20.27ms; fastest: 0.07ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 4 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1beta4
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 41348
WiFi IP address 192.168.10.50
Signal strength -46dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0
15.12.2023, 16:57:33	M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.1++wdb (2023-12-11 09:30:48) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 102844
Dynamic ram: 122016 of which 0 recycled
Never used RAM 13700, free system stack 184 words
Tasks: NETWORK(1,ready,24.6%,227) HEAT(3,nWait,0.0%,352) Move(4,nWait,0.0%,358) CanReceiv(6,nWait,0.0%,797) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,nWait,0.7%,108) MAIN(1,running,67.6%,670) IDLE(0,ready,6.1%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:24:30 ago, cause: software
Last software reset at 2023-12-15 16:33, reason: HardFault bfarValid precise, Platform spinning, available RAM 13676, slot 0
Software reset code 0x4060 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x00000803 BFAR 0x312e303d SP 0x20011f60 Task NETW Freestk 472 ok
Stack: 312e303d 20032cad 00000047 312e303c 20032e6c 0002dd7f 00004434 210f0000 0002dd27 2002bed4 2002be01 000001c0 2002c138 20031c70 2002c150 2001e888 a5a5a5a5 a5a5a5a5 0002ff75 00000000 00000000 00000000 312e303d 00000800 20034fa0 2002c138 20018678
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 1470513, completed 1470512, timed out 0, errs 0
MCU temperature: min 35.9, current 36.2, max 36.3
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/23, heap memory allocated/used/recyclable 2048/1496/1184, gc cycles 2757
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 16, read errors 0, write errors 0, ifcnt 72, reads 314, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 16, read errors 0, write errors 0, ifcnt 72, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 0, ifcnt 60, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 61, reads 315, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 60, reads 314, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-15 16:57:46
Cache data hit count 2535039282
Slowest loop: 6.44ms; fastest: 0.15ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 4.0ms, write time 1.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
in 0 notIn 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 54, received 123, lost 0, errs 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 6, free buffers 26 (min 26), ts 30/30/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 20.27ms; fastest: 0.07ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 4 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1beta4
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 41348
WiFi IP address 192.168.10.x
Signal strength -46dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0

[dc42]

@NeoDue yes please send a M122 report any time after the Duet crashes. If the crashes you get on the 6HC are similar to the ones that @Exerqtor gets on the Duet 3 Mini, that would be very interesting indeed.

[Exerqtor]

@dc42
I don't want to yell hallelujah to early, but this seems promising.

The machine haven't had a single crash since i updated to WiFiServer 2.1b6 (and RRF 3.5.0-rc2), with the same setup as earlier in regard to open DWC instances.

Scratch that, windows has apparently ran one of it's Nazi updates rendering both Chrome and Orca Slicer closed without me knowing, until just now. So the "test parameters" are't valid, i'll report back later 🤦‍♂️

---

The 1LC reversing issue does stil presist though 😓

[NeoDue]

@Exerqtor it seems the update I got right when I wanted to start testing has found its way to you You can check in the Windows event log when the computer rebooted and take the time until that happened as valid test time.

@dc42 so far, my Duet is running for about 36 hours with the computer connected without crashing - it should have done that by now. This means either something having changed on the notebook (Windows update, browser update) or beta6 of the Wifi software has made some significant difference. I will keep it running. If something changes, I will note it here and post the M122 as you requested!

[Exerqtor]

@NeoDue said in Reboots/crashes - RRF 3.5.0-rc1:

@Exerqtor it seems the update I got right when I wanted to start testing has found its way to you You can check in the Windows event log when the computer rebooted and take the time until that happened as valid test time.

Yeah i could, but i'm having some other issues with 2.1b6 allready. It's dropping connection when not in use and some times it's not able to connect to at all. Only way to fix that has been to toggle the WiFi adapter 😮‍💨

[NeoDue]

@Exerqtor Weird. I had connection issues with the previous versions with connections dropping sometimes and especially the Wifi module frequently only connecting after 10+ minutes (could be partially cured by turning wifi in config.pro on at the end and after an additional 10s G4 delay in front of the command). b6 has solved these for me.
One hint: if such an error happens, you might get brief error messages on the PanelDue which will not show up on DWC. But that is a different topic...

[Exerqtor]

@NeoDue said in Reboots/crashes - RRF 3.5.0-rc1:

@Exerqtor Weird. I had connection issues with the previous versions with connections dropping sometimes and especially the Wifi module frequently only connecting after 10+ minutes (could be partially cured by turning wifi in config.pro on at the end and after an additional 10s G4 delay in front of the command). b6 has solved these for me.
One hint: if such an error happens, you might get brief error messages on the PanelDue which will not show up on DWC. But that is a different topic...

I can live with loosing connection over it crashing though thats for sure.

But i've managed to get three instances connected now (2x chrome, 1x orca slicer) and it's standing there idle. So lets see if anything happens.

[Exerqtor]

@dc42 It's crashing on 3.5.0-rc2 & 2.1b6 as well:

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5.0-rc.2 (2023-12-15 13:33:26) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: XNHXF-HR6KL-K65J0-409N2-K9W1Z-RV2MZ
Used output buffers: 13 of 40 (40 max)
=== RTOS ===
Static ram: 102812
Dynamic ram: 122028 of which 12 recycled
Never used RAM 13708, free system stack 180 words
Tasks: NETWORK(2,nWait,24.5%,230) HEAT(3,nWait,0.0%,336) Move(4,nWait,0.0%,351) CanReceiv(6,nWait,0.0%,776) CanSender(5,nWait,0.0%,336) CanClock(7,delaying,0.0%,350) TMC(4,nWait,0.7%,108) MAIN(1,running,67.7%,670) IDLE(0,ready,6.2%,29) AIN(4,delaying,0.8%,264), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 01:43:42 ago, cause: software
Last software reset at 2023-12-16 19:41, reason: HardFault invState, Platform spinning, available RAM 12548, slot 1
Software reset code 0x4060 HFSR 0x40000000 CFSR 0x00020000 ICSR 0x00000803 BFAR 0xe000ed38 SP 0x20011f88 Task NETW Freestk 482 ok
Stack: 000001af 00000002 200014e8 00000000 20032e5b 0009edb1 00000000 600f0000 00000000 00000000 00000000 00000000 20031c74 00000800 20035968 2002c0e0 20018660 2002bf7d 20018660 2001e868 0002ffc3 00000000 00000000 00000000 20012038 00000014 ffffffff
Error status: 0x04
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 6223000, completed 6223000, timed out 0, errs 0
MCU temperature: min 35.3, current 35.7, max 35.7
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/22, heap memory allocated/used/recyclable 2048/1908/1608, gc cycles 11636
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 2, read errors 0, write errors 0, ifcnt 59, reads 187, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 4, read errors 0, write errors 0, ifcnt 59, reads 187, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 2, read errors 0, write errors 0, ifcnt 198, reads 187, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 199, reads 187, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 197, reads 187, writes 0, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-12-16 21:24:46
Cache data hit count 4294967295
Slowest loop: 7.71ms; fastest: 0.18ms
=== Storage ===
Free file entries: 18
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.9ms, write time 4.1ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0 0, running macro
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
check 0 clear 0
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 31, received 71, lost 0, errs 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 3, free buffers 26 (min 26), ts 17/17/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 21.20ms; fastest: 0.06ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 4 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1beta6
MAC address c4:5b:be:ce:91:93
Module reset reason: Power up, Vcc 3.38, flash size 2097152, free heap 42812
WiFi IP address 192.168.10.x
Signal strength -46dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0