RepRapFirmware 3.6.0-alpha.2 for Duet main boards available

DonStauffer

@dc42 Thanks for the information.

balajiramani

Hi am seeing a new error today. A few minutes into a print, the printer stopped with the following error:

Error: Movement halted because a step timing error occurred (code 3). Please reset the controller.

Here is the output of M122 after that:

8/18/2024, 5:05:27 PM   M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.6.0-alpha.4 (2024-08-13 15:11:39) running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6JTDL-3SS6N-968BX
Used output buffers: 12 of 26 (21 max)
=== RTOS ===
Static ram: 23368
Dynamic ram: 66976 of which 12 recycled
Never used RAM 16440, free system stack 112 words
Tasks: NETWORK(2,nWait 6,15.9%,195) HEAT(3,nWait 5,0.1%,328) Move(4,invalid,1.1%,272) MAIN(1,running,82.9%,744) IDLE(0,ready,0.0%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 01:00:54 ago, cause: power up
Last software reset at 2024-08-09 19:04, reason: User, Gcodes spinning, available RAM 13844, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 38.2, current 46.3, max 49.1
Supply voltage: min 23.5, current 24.2, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/3, heap memory allocated/used/recyclable 2048/1184/1096, gc cycles 1
Events: 0 queued, 0 completed
Date/time: 2024-08-18 17:05:26
Slowest loop: 226.73ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 8
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 6.2ms, write time 4.3ms, max retries 0
=== Move ===
Segments created 470, maxWait 2498505ms, bed comp in use: none, height map offset 0.000, hiccups added 1 (0.03ms), max steps late 0, ebfmin 0.00, ebfmax 0.00, mcet 0.085
Pos req/act/dcf: 68507.00/68479/0.99 65547.00/65566/-0.81 65391.00/65409/-0.99
no step interrupt scheduled
Driver 0: standstill, SG min 0
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min 0
Driver 3: standstill, SG min 0
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
=== DDARing 0 ===
Scheduled moves 69133, completed 69131, LaErrors 0, Underruns [0, 0, 0]
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.2
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X-13.401 Y-8.549" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 1
Code queue 0 is empty
=== Network ===
Slowest loop: 208.96ms; fastest: 0.00ms
Responder states: HTTP(4) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1.0
MAC address 5c:cf:7f:2c:25:00
Module reset reason: Turned on by main processor, Vcc 3.40, flash size 4194304, free heap 40988
WiFi IP address 192.168.1.61
Signal strength -36dBm, channel 6, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

dc42

@balajiramani please share the GCode file that provoked that message and your config.g file.

balajiramani

@dc42 Here is the gcode - Uno_CNC_Back_0.2mm_PLA_BigDelta_28m.gcode

Here is config.g

; Setup some global variables
global power_fail_retract = 2   ;  Retract 2mm when power fails

; Communication and general
M550 P"BigDelta"				        ; Machine name and Netbios name (can be anything you like)
M551 Preprap                        	; Machine password (used for FTP)
M552 S1					                ; Enable WiFi. Disabled for setup and testing. Enable once set up on your network.

; Enable telnet
M586 S1 P2

; Debugging
M111 S0                                 ; Debug off
M929 P"eventlog.txt" S1                 ; Start logging to file eventlog.txt

M555 P2                           	    ; Set output to look like Marlin
G21                                 	; Work in millimetres
G90                                	    ; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes backwards
M569 P1 S0				; Drive 1 goes backwards
M569 P2 S0				; Drive 2 goes backwards
M569 P3 S0				; Drive 3 goes backwards

; Assign extruder drive
M584 E3


; Set homing switch config
M574 X2 S1 P"!xstop"        ; Set homing switch configuration on S1 = high-end, active-low
M574 Y2 S1 P"!ystop"        ; Set homing switch configuration on S1 = high-end, active-low
M574 Z2 S1 P"!zstop"        ; Set homing switch configuration on S1 = high-end, active-low

; Set it as a linear delta
M669 K3

; Setup paneldue 5i
M575 P1 S1 B57600

M665 R215.062 L395.317:395.475:395.433 B160 H374.050		; set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0				; put your endstop adjustments here, or let auto calibration find them
M350 X16 Y16 Z16 E16 I1    	; Set 16x microstepping with interpolation
M92 X200 Y200 Z200			; Set axis steps/mm

M906 X1400 Y1400 Z1400 E1400 I60	; Set motor currents (mA) and increase idle current to 60%
M84 S60                             ; Set idle timeout
M201 X12000 Y12000 Z2000 E10000     ; Accelerations (mm/s^2)
M203 X30000 Y30000 Z5000 E3600		; Maximum speeds (mm/min)
;M566 X900 Y900 Z300 E1200 P1		; Maximum instant speed changes mm/minute
;M566 X300 Y300 Z300 E450 P1        ; Maximum instant speed changes mm/minute
M566 X600 Y600 Z300 E900 P1		    ; Maximum instant speed changes mm/minute
M204 P9000 T9000                    ; Set acceleration for print and travel moves

; Configure Input shaping
M593 P"zvdd" F45

; Thermistors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 R4700 H30 L0	; Put your own H and/or L values here to set the bed thermistor ADC correction
M308 S1 P"e0_temp" Y"thermistor" T100000 B3950 R4700 H30 L0	; 100K NTC 
;M308 S1 P"e0_temp" Y"thermistor" T100000 B4658 C6.5338987554e-08 ; 104-NT Aliexpress thermistor

M950 H0 C"bed_heat" T0      ; Set up H0 as the bed heater using T0 as the sensor
M950 H1 C"e0_heat" T1       ; Set up H1 as the extruder heater using T1 as the sensor
M140 H0                     ; Map H0 as the bed heater

; Set temperature excursion warnings
M570 H0 P20
M570 H1 P20

M308 S3 Y"mcu-temp" A"MCU" ; configure sensor 3 as thermistor on pin e1temp for left stepper
M308 S4	Y"drivers"  A"Drivers"  ; configure sensor 4 as temperature warning and overheat flags on the TMC2660 on Duet
M912 P0 S-3.5               ; Calibrate MCU temp

; Fan definitions
M950 F0 C"fan0"
M950 F1 C"fan1"
M950 F2 C"fan2"

; Thermostatic fan on 1 for cooling the hotend
M106 P1 T50 H1
; Thermostatic fan on 2 for cooling the board
M106 P2 H3:4 L.3 X1 B0.3 T35:70 ; set fan 2 value

; Tool definitions
M563 P0 D0 H1                       	; Define tool 0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures
;M92 E1392								; Based on https://www.thingiverse.com/thing:1359717; 2023/01/06
M92 E1077.1646                          ; This is the new value for the hobb-goblin extruder.  03/07/2023
;M92 E319.2005                           ; Set extruder steps per mm.  This is for the MK8 gear

; Z probe and compensation definition
M558 P8 C"^!zprobe.in" R0.4 H4 F1200 T6000 A5 S0.01	; Z probe is a piezo sensor
G31 X0 Y0 Z-0.08 P100			; Set the zprobe height and threshold
M557 R150 S20				; Probe within a radius of 150mm and mesh spacing of 20
M376 H5                     ; Taper off bed compensation after 5mm

; Configure power failure and resume
M911 S21.0 R23.0 P"G91 M83 G1 Z3 E{-global.power_fail_retract} F1000" ; Relative movement and extrusion.  Move head up and retract 2mm filament.

M208 S1 Z-0.5				; set minimum Z
T0					        ; select first hot end

M501					    ; Load any config overrides

DonStauffer

This post is deleted!

curieos

Does alpha 4 still work with toolboards running 3.5.2? I'd like to give this a try, but the toolboard on my Micron is a Fly RRF 36 and it doesn't look like team gloomy is releasing 3.6 alpha builds.

Notepad

@curieos Looks like a question for @jay_s_uk @gloomyandy

dc42

@curieos said in RepRapFirmware 3.6.0-alpha.2 for Duet main boards available:

Does alpha 4 still work with toolboards running 3.5.2? I'd like to give this a try, but the toolboard on my Micron is a Fly RRF 36 and it doesn't look like team gloomy is releasing 3.6 alpha builds.

Yes it does.

gloomyandy

@Notepad I don't think there are any expansion builds publicly available for 3.6 yet. We did make a build of 3.6 for mainboards available here: https://discord.com/channels/711873626080804914/762765744278208512/1263573562090848286

As DC42 confirmed existing 3.5.2 builds for expansion boards can be used with 3.6.

balajiramani

@dc42 checking if there is any update on this issue?

oliof

@balajiramani multiple issues have been discussed here, it helps if you're specific on which one you are asking about.

curieos

I've done a couple prints now on my Micron, and input shaping is looking way better. There's a symptom I didn't realize was due to the old input shaping algorithm; large ringing artifacts on organic supports. My guess is it's due to the high segmentation of those moves, but I could hear the printer make an almost grinding noise. That's all gone now.

The main quirk I'm noticing is slow probing. I'm running a klicky PBC and before, when the probe triggered, it would retract near instantly. Now it pauses after triggering for a brief moment. I have it set up to do multiple samples, and it seems like the first sample is always the slowest when retracting, but every sample has a brief pause.

Pressure advance also seems kinda weird. I need to rerun the tuning pattern to be sure I'm using the correct value, but it looks like turning it on at all has a very negative effect on surface quality. It's most pronounced on the latest print, but that's still in progress.

dc42

@curieos thanks for your feedback. Re the pressure advance, is the extruder driven by the main board, or by a tool or expansion board - and if so, is that board running 3.5 or 3.6 firmware?

curieos

@dc42 It's on the mellowfly toolboard running 3.5.2

dc42

@curieos OK, please upgrade to 3.6.0-alpha.4+3. See my next post.

dc42

All those running 3.6.0alpha builds, please see my announcement at https://forum.duet3d.com/topic/36421/reprapfirmware-3-6-0-alpha-4-3-available-for-testing/1 and upgrade to that version. If you find any issues, please continue in that thread. I shall lock this one shortly.