Error: G1: intermediate position outside machine limits
-
this is doing my head in
was working find now suddenly it doesn't work any more01-TCM-03-029 REVB_ABS_6h6m_nozzle_0.6.gcode
3.6.0-beta.2 and just tested its same with 3.5.4
there is nothing obvious in the gcode and it is working on the other machine
@dc42config.g
; Configuration file for Duet 3 Mini 5+ (firmware version 3) ; executed by the firmware on start-up G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Vega2.0" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S1 D3 V40 ; physical drive 0.0 goes forwards M569 P0.1 S0 D3 V40 ; physical drive 0.1 goes forwards M569 P0.2 S1 D3 V40 ; physical drive 0.2 goes forwards M569 P0.3 S1 D3 V40 ; physical drive 0.3 goes forwards M569 P0.4 S0 D3 V40 ; physical drive 0.4 goes forwards M584 X0.0 Y0.1 Z0.4 E0.2 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y80.00 Z1920.00 E400.00 ; set steps per mm M566 X300.00 Y300.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min) M201 X2500.00 Y2500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X1200 Y1200 Z900 E650 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S90 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X320 Y300 Z350 S0 ; set axis maxima ; Endstops M574 X1 S1 P"io2.in" ; configure active-high endstop for low end on X via pin !io2.in M574 Y2 S1 P"!io4.in" ; configure active-high endstop for low end on Y via pin !io4.in M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe ;M950 S0 C"io3.out" M950 S0 C"121.io0.out" ; create servo pin 0 for BLTouch ;M558 P9 C"^io3.in" H5 F120 T6000 M558 P9 C"121.^io0.in" H5 F3000 T8000 S0.25 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X-30 Y10 Z4 ; set Z probe trigger value, offset and trigger height M557 X20:280 Y20:280 S60 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S160 ; set temperature limit for heater 0 to 120C M308 S1 P"temp1" Y"pt1000" R2200 ; configure sensor 1 as PT1000 on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S350 ; set temperature limit for heater 1 to 350C M308 S2 P"temp2" Y"pt1000" R2200 ; configure sensor 2 as PT1000 on pin temp2 M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2 M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H2 S350 ; set temperature limit for heater 2 to 350C ; Fans M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off M950 F2 C"out5" Q500 ; create fan 2 on pin out5 and set its frequency M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on M950 F3 C"out6" Q500 ; create fan 3 on pin out6 and set its frequency M106 P3 S1 H2 T45 ; set fan 3 value. Thermostatic control is turned on ; Tools M563 P0 S"Left Extruder" D0 H1 F0 ; define tool 1 G10 P0 X0 Y0 Z0 ; set tool 1 axis offsets G10 P0 R0 S0 ; set initial tool 1 active and standby temperatures to 0C ; ; Custom settings are not defined ; Miscellaneous M575 P1 S0 B57600 ; enable support for PanelDue M501 ; load saved parameters from non-volatile memory ; T0 ; select first tool -
@Aurimas At what point during the job do you get the message? I assume at the start?
The job start sequence appears to be to home all, move the nozzle to Y1 Z3, wait for temperatures, then do a mesh scan of the print area. Does that all work?
Ian
TronXY X5S with Duet 3 MB6HC and Roto toolboard : Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : Polargraph with Duet 2 WiFi
-
@droftarts said in Error: G1: intermediate position outside machine limits:
The job start sequence appears to be to home all, move the nozzle to Y1 Z3, wait for temperatures, then do a mesh scan of the print area. Does that all work?
yes - it freaks out in the middle of the bed for some of the sections and then continues like nothing happenned and freaks out again later.
as you can imagine there are puddles of plastic where it is freaking out
