Duet firmware 2.03beta3 available

dc42

@wilriker said in Duet firmware 2.03beta3 available:

Typo in release notes:

Known issues:

Custom endstop input numbers in the M575 command (probe tool) don't work

Probe tool is M585. Also I am particularly interested in getting this fixed. Is that planned to be done before 2.03 final?

Yes it will be fixed, probably in the next beta.

wilriker

@dc42 Thanks!

gavatron3000

M291 doesnt pause a tool change if the message is blocking ie M291 S2, the message now appears at the correct time but the tool change carrys on anyway until completed.

dc42

@gavatron3000 said in Duet firmware 2.03beta3 available:

M291 doesnt pause a tool change if the message is blocking ie M291 S2, the message now appears at the correct time but the tool change carrys on anyway until completed.

On my list to investigate.

gavatron3000

thank you

paboman

Updated to the 2.03beta3 then when uploading the last DuetWiFiServer.bin I get SKIPPED as response from DWC, why ?
thx

dc42

@paboman said in Duet firmware 2.03beta3 available:

Updated to the 2.03beta3 then when uploading the last DuetWiFiServer.bin I get SKIPPED as response from DWC, why ?
thx

That happens if you upload DuetWiFiServer.bin to a board other than a Duet WiFi. What board do you have, and what does Duet Web Control think it is?

paboman

@dc42 its an ethernet version, do I need that file ?

wilriker

@paboman No, this file is only for the Wifi version.

DaveA

I Just installed beta3 and it's running well on my cartesian but I'm having an issue on the delta with smart effector. I decided to make a nozzle change that required me to reset the trigger height in the G31 and things have gone downhill from there.

I am running through the steps of jogging Z until I get my paper trapped then...
Do G92 Z0
Do G1 Z25
Do G30 S-1
Get value from M114 and enter it into my G31 entry in config.g. So my config is now:
M208 S1 Z-2.0
M558 P8 R0.5 H12 F1000 T8000
G31 X0 Y0 Z-0.32 P100
Reboot...
G28
G1 Z0 <<- slight hit on bed. Absolutely no clearance. Need to jog Z up by .35 to get clearance

I've run this a bunch of times with no luck and I'm starting to think that the Z value in the G31 is being ignored. I have looked and there is no other G31 anywhere.

Did the procedure change or is my process wrong?

dc42

@davea said in Duet firmware 2.03beta3 available:

Get value from M114 and enter it into my G31 entry in config.g.

Don't do that. Use the value that the firmware reports after the G31 S-1 command instead.

DaveA

Just ran the sequence again and used the value displayed in the results box (Stopped at height -0.319) . Updated G31 with no change in outcome - still slight hit on the bed. Need to jog Z up by .30ish to get clearance back.

Also tried the same sequence on the cartesian and it appears to work as expected.

dc42

On a delta, if you change the Z probe trigger height then you will also need to correct the homed height (M665 H parameter). The easiest way to do this is to run auto calibration, then save the new H value. Or you could just reduce the M665 H parameter by 0.3 in config.g or config-override.g as appropriate.

gavatron3000

Apart from the m291 issue I raised above. CoreXZ running normally. Just completed a 4 hour print

dc42

@gavatron3000 said in Duet firmware 2.03beta3 available:

Apart from the m291 issue I raised above. CoreXZ running normally. Just completed a 4 hour print

Thanks for the feedback!

whosrdaddy

Ran a 2 hour print on my CoreXY yesterday, no problems to report

boldnuts

Ran a 3 hour print on my Delta yesterday, no problems to report

DaveA

@dc42 I just tried this again and ran a G32 followed by M500 and a reboot. Now when I run G28 and do a G1 Z0 the nozzle is now above the bed by about .65 which is about double the trigger height of .32.

Any idea what I'm doing wrong here?

0_1553688682980_config.g
0_1553688695343_config-override.g
0_1553688905882_bed.g

dc42

@DaveA, what type of Z probe is it, and how did you measure the trigger height?

Please check with M115 that you really are running firmware 2.03beta3.

DaveA

@dc42 I'm using a smart effector and the firmware is 2.03b3.
I set the trigger height by trapping a 4mil (.102mm) feeler guage. I then reset to zero with G92 Z0. Then step up about 20mm and do G30 S-1. I was getting the distance from M114 but then used the value reported in the little G30 status box. I then update the G31 value in config.g and then do a G32. Then reboot.

I have partially solved the issue by changing the bed.g file to use S6 instead of S9 for the last G30. I'm somewhat confused as I've not changed the bed.g file since last August and the printer has been printing fine. I do a G32 as part of my start script.