Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. DNvM84
    • Profile
    • Following 0
    • Followers 0
    • Topics 3
    • Posts 21
    • Best 3
    • Controversial 0
    • Groups 0

    DNvM84

    @DNvM84

    3
    Reputation
    1
    Profile views
    21
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    DNvM84 Unfollow Follow

    Best posts made by DNvM84

    • RE: AI Print Monitoring / Printer Health monitoring

      @Peter-Lebiedzinski
      Hi Peter, I received your email.
      Any recommendations as to where the camera should be placed?
      I ask because while I was researching other versions of monitoring software, they stated that the camera should be looking at the table at no more than a specified angle above the build surface.

      Thank you for keeping me in the loop.
      DNvM

      posted in General Discussion
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @engikeneer
      Thank you for your reply.

      I understand my way of thinking is based on a very hypothetical possibility.
      With working around machines and tools all my life it is just the way I think.

      Thank you for the information, I will have to look into that relay system.

      @Phaedrux
      Thank you for your patience and the detail of your explanations.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      Hello, everyone, thank you for the replies.

      As my final entry what I have done is place M1 at the end of my End G-Code.

      And that does exactly what I need it to do.

      Again, thank you for all off your suggestions and help.

      One last question. How do I mark this as solved?

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84

    Latest posts made by DNvM84

    • RE: AI Print Monitoring / Printer Health monitoring

      @Peter-Lebiedzinski
      Hi Peter, I received your email.
      Any recommendations as to where the camera should be placed?
      I ask because while I was researching other versions of monitoring software, they stated that the camera should be looking at the table at no more than a specified angle above the build surface.

      Thank you for keeping me in the loop.
      DNvM

      posted in General Discussion
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      Hello, everyone, thank you for the replies.

      As my final entry what I have done is place M1 at the end of my End G-Code.

      And that does exactly what I need it to do.

      Again, thank you for all off your suggestions and help.

      One last question. How do I mark this as solved?

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @engikeneer
      Thank you for your reply.

      I understand my way of thinking is based on a very hypothetical possibility.
      With working around machines and tools all my life it is just the way I think.

      Thank you for the information, I will have to look into that relay system.

      @Phaedrux
      Thank you for your patience and the detail of your explanations.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      You are correct. I see Active as powered on, even if the temperature equals zero.
      When you look at the PanelDue the heater icon is red, again showing me that the heater is powered on.

      What do I do when I start using dual print heads? If T-1 only deselects the current head then the other head will stay in standby mode. And if it has a set temperature it will stay hot.

      I don't understand why there is not an easy way to turn the heater power off. Not just set the temp to zero. To me this is a safety hazard. Hypothetical if this was a manufacturing setting there is no way a company would allow the heater to stay energized. All it would take is one mistake and somebody could get burns.

      Again thank you for you help.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      So does that mean I need T-0 and T-1?

      Thank you.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      Hello, so I placed the following M568 codes in Cura and unfortunately it made no difference.
      ;End G-Code
      M568 P0 A0
      M568 P1 A0
      ;Retract the filament
      G92 E1
      G1 E-1 F300
      G28 X0 Y0
      M84
      I know you state that it makes no difference but I personally dislike the idea of the heater being active.
      So if you have any other ideas I would like to hear them.

      Maybe I should also contact Modix support and see what they say.

      Thank you.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      I added the M568 lines to the End G-Code and I will run a test print.

      I really appreciate your help.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      You are correct I am getting confused.
      When working through the Web Controller the heater has three settings.
      Off, Active, and Standby. Before updating to 3.3 when a print was finished the heater would be turned off.
      If just setting the temperature to zero turns off the heater why have the option to turn the heater off?

      That is why I am confused.

      Thank you.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      In Cura I have the following:
      M104 S0
      M140 S0
      :Retract The Filament
      G92 E1
      G1 E-1 F300
      G28 X0 Y0
      M84
      I do understand the idea that if the temperature is set to zero the heater is basically off. But like I mentioned in two places it states that the heater is still considered "Active".
      So if I understand, if I put T-0 and T-1 in the "End G-Code that will deactivate the heaters?
      Or is it better to say:
      M568 P0 A0
      M568 P1 A0
      I am not worried about what the active temperature reads as long as the heaters are deactivated.

      Thank you again for all of your help.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84
    • RE: Extrusion heater not turning off

      @phaedrux
      Thank you for the reply.
      According to Duet Web Control and on the touch panel the heater is still active. Somehow the temperature setting has been set to zero.
      I want the heater to be turned off.

      Sorry I should have better explained that.

      posted in Tuning and tweaking
      DNvM84undefined
      DNvM84