@droftarts that worked! Thank you!

The Bltouch does a slef test when I turn on printer, I cant do anythign else with it, I know that I have the config screwed up for the Z-probe. Can someone give me the proper code for the bltouch hooked up tp a Toolboard 1LC to put in my config file.

 ; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Apr 15 2023 20:09:14 GMT-0500 (Central Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Duet 3"                                     ; set printer name

; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
M569 P0.1 S0                                       ; physical drive 0.1 goes forwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S0                                       ; physical drive 0.3 goes forwards
M569 P0.4 S0  
M569 P0.5 S1  
M569 P121.0 S0                                     ; physical drive 121.0 goes backwards
M584 X0.5 Y0.1:0.2 Z0.3 E121.0                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00                  ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z1500 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X-150 Y-150 Z0 S1                                   ; set axis minima
M208 X150 Y150 Z385 S0                             ; set axis maxima

; Endstops
M574 X1 S3                                         ; configure sensorless endstop for low end on X
M574 Y1 S3                                         ; configure sensorless endstop for low end on Y

; Z-Probe
M558 P9 C"io0.out" H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138       ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0                                 ; create bed heater output on out1 and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"121.temp0" Y"thermistor" T100000 B4138   ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1                             ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"121.out1" Q500                           ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500                           ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 H1 T45                                     ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@oliof Thank you, got it updated1

I have a Duet 3 6HC with a Raspberry Pi and Toolboard 1LC.

The Duet 3 6HC firmware is RepRapFirmware for Duet 3 MB6HC 3.4.4+1 (2022-11-15)
Duet TOOL1LC firmware version 3.3 (2021-06-15 16:12:58)

How do I update the firmware on the toolboard and is there a link to the toolboards latest firmware(I cannot find it anywhere)

Im trying to install an new Duet 2 wifi board, the link to the Windows USB Drivers is broken, anyone have a working link?

here is the broken link:
https://github.com/Duet3D/RepRapFirmware/blob/dev/Driver/DuetDriverFiles.zip

Try it now

No, nothing shorting against the board, it was mounted on 20mm printed stand offs, then I put nylon washers between the board and the screws. So its, screw, nylon washer, board, 20mm 3d printed standoff, mounted to a melamine board.

Bought the board in 2018, but sadly, It was for a project that I had set aside and didn't get back to till about 3 weeks ago, so the board had probally been used less then 50 times total.

https://drive.google.com/file/d/1bjw1bgBfpSLfJ_P6Pq1asx-cXwlaMBEv/view?usp=drivesdk

https://drive.google.com/file/d/1bjptjoMHgpWTFbWczqt_GfarV0bqMLCg/view?usp=drivesdk

Supprised, figured I'd get a little more help on this then I did....

Well, I never figured out what the issue is, but its something with the board itself, I changed it with another duet I have on a different printer and no problems now.

Yes, that message comes up on the PanelDue