Posts made by Bmilam

@droftarts that worked! Thank you!

The Bltouch does a slef test when I turn on printer, I cant do anythign else with it, I know that I have the config screwed up for the Z-probe. Can someone give me the proper code for the bltouch hooked up tp a Toolboard 1LC to put in my config file.

 ; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat Apr 15 2023 20:09:14 GMT-0500 (Central Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Duet 3"                                     ; set printer name

; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
M569 P0.1 S0                                       ; physical drive 0.1 goes forwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S0                                       ; physical drive 0.3 goes forwards
M569 P0.4 S0  
M569 P0.5 S1  
M569 P121.0 S0                                     ; physical drive 121.0 goes backwards
M584 X0.5 Y0.1:0.2 Z0.3 E121.0                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00                  ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z1500 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X-150 Y-150 Z0 S1                                   ; set axis minima
M208 X150 Y150 Z385 S0                             ; set axis maxima

; Endstops
M574 X1 S3                                         ; configure sensorless endstop for low end on X
M574 Y1 S3                                         ; configure sensorless endstop for low end on Y

; Z-Probe
M558 P9 C"io0.out" H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                           ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138       ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0                                 ; create bed heater output on out1 and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"121.temp0" Y"thermistor" T100000 B4138   ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1                             ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"121.out1" Q500                           ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500                           ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 H1 T45                                     ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

@oliof Thank you, got it updated1

I have a Duet 3 6HC with a Raspberry Pi and Toolboard 1LC.

The Duet 3 6HC firmware is RepRapFirmware for Duet 3 MB6HC 3.4.4+1 (2022-11-15)
Duet TOOL1LC firmware version 3.3 (2021-06-15 16:12:58)

How do I update the firmware on the toolboard and is there a link to the toolboards latest firmware(I cannot find it anywhere)

Im trying to install an new Duet 2 wifi board, the link to the Windows USB Drivers is broken, anyone have a working link?

here is the broken link:
https://github.com/Duet3D/RepRapFirmware/blob/dev/Driver/DuetDriverFiles.zip

Try it now

No, nothing shorting against the board, it was mounted on 20mm printed stand offs, then I put nylon washers between the board and the screws. So its, screw, nylon washer, board, 20mm 3d printed standoff, mounted to a melamine board.

Bought the board in 2018, but sadly, It was for a project that I had set aside and didn't get back to till about 3 weeks ago, so the board had probally been used less then 50 times total.

https://drive.google.com/file/d/1bjw1bgBfpSLfJ_P6Pq1asx-cXwlaMBEv/view?usp=drivesdk

https://drive.google.com/file/d/1bjptjoMHgpWTFbWczqt_GfarV0bqMLCg/view?usp=drivesdk

Supprised, figured I'd get a little more help on this then I did....

Well, I never figured out what the issue is, but its something with the board itself, I changed it with another duet I have on a different printer and no problems now.

Yes, that message comes up on the PanelDue

I don't even know if reset is the right term, because after the printer stops, the progress bar shows 100% like the print completed

The printer just stops in mid movement and the layer fan shuts off.

Everytime it resets, I get this massage on the counsole.

https://drive.google.com/file/d/1baVuvLro9hD_JT6FbqInWpsegVn8Mlew/view?usp=drivesdk

Yes I did do a re-tune on the hotend. I did consider the pump might be causing the resets, but after switching the board over the the 800watt atx psu and leaving the rest hooked up to the old PSU, it still is resetting.

This started after I put on a water cooled hotend, the E3d Titan Aqua, the only thing I can think of is, now there is no hotend fan hooked to the duet board, the water cooling pump and rad/fan are powered directly by the PSU. I don't know if the issue is a coincidence or is the duet resetting because its not sinsing a hotend fan being hooked up?

other then that, nothing has changed, I used the same heater, same thermistor, heater block, motor that was already there from the regular e3d titan.

Here is the m122 after that print failled

4/26/2020, 6:18:37 PM	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9568A-F23SD-6J9DL-3SN6K-KTRZH
Used output buffers: 1 of 24 (19 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93140 of which 0 recycled
Exception stack ram used: 320
Never used ram: 11900
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3760) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:06:38 ago, cause: power up
Last software reset at 2020-04-26 17:24, reason: User, spinning module GCodes, available RAM 11900 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 27.6, current 27.8, max 29.5
Supply voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-04-26 18:18:36
Cache data hit count 1214738893
Slowest loop: 2.43ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 51.93ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 2c:3a:e8:0b:02:f1
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 14504
WiFi IP address 192.168.1.137
WiFi signal strength -68dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

here is my config file

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Wed Apr 01 2020 17:56:19 GMT-0500 (Central Daylight Time)

; General preferences
G90                                      ; send absolute coordinates...
M83                                      ; ...but relative extruder moves
M550 P"FT5"                              ; set printer name

; Network
M552 S1                                  ; enable network
M586 P0 S1                               ; enable HTTP
M586 P1 S0                               ; disable FTP
M586 P2 S0                               ; disable Telnet

; Drives
M569 P0 S0                               ; physical drive 0 goes forwards
M569 P1 S0                               ; physical drive 1 goes forwards
M569 P2 S0                               ; physical drive 2 goes forwards
M569 P3 S1                               ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                  ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E837      ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E1500.00     ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00  ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E3000      ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z2000 E1400 I30         ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
;M208 X0 Y-10 Z0 S0                      ; set axis minima
;M208 X300 Y300 Z400 S0                  ; set axis maxima
M208 X-150:150 Y-150:150                 ; set axis limits
; Endstops
M574 X1 Y1 S0                            ; set active low and disabled endstops
M574 Z1 S2                               ; set endstops controlled by probe

; Z-Probe
M307 H3 A-1 C-1 D-1                          ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000                        ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X48 Y-5 Z4                           ; set Z probe trigger value, offset and trigger height
M557 X-145:145 Y-145:145 S30                 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700              ; set thermistor + ADC parameters for heater 0
M143 H0 S120                             ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280                             ; set temperature limit for heater 1 to 280C
M307 H1 A715.3, C248.3, D7.8 S1          ; PID for hotend
; Fans
M106 P0 S0 I0 F500 H-1                   ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                         ; define tool 0
G10 P0 X0 Y0 Z0                          ; set tool 0 axis offsets
G10 P0 R0 S0                             ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

Ok here is the m122 a few minutes after the print started.

4/26/2020, 6:06:24 PM	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9568A-F23SD-6J9DL-3SN6K-KTRZH
Used output buffers: 3 of 24 (19 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93176 of which 0 recycled
Exception stack ram used: 440
Never used ram: 11744
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3736) IDLE(ready,160)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:09:40 ago, cause: power up
Last software reset at 2020-04-26 17:24, reason: User, spinning module GCodes, available RAM 11900 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 28.0, current 28.6, max 29.0
Supply voltage: min 12.0, current 12.1, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/467
Driver 1: standstill, SG min/max 0/360
Driver 2: ok, SG min/max not available
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2020-04-26 18:06:24
Cache data hit count 1730644159
Slowest loop: 2.33ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 159, MinFreeDm: 128, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves: 1930, completed moves: 1890, StepErrors: 0, LaErrors: 0, Underruns: 0, 1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X-14.396 Y-7.509 E1.7842" in state(s) 0
serial is idle in state(s) 0
aux is ready with "M408 S1" in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 175.22ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 2c:3a:e8:0b:02:f1
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 14824
WiFi IP address 192.168.1.137
WiFi signal strength -68dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

It happened again after I switched the PSU. Here is the latest M122

4/26/2020, 5:04:28 PM: m122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9568A-F23SD-6J9DL-3SN6K-KTRZH
Used output buffers: 3 of 24 (20 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93140 of which 0 recycled
Exception stack ram used: 320
Never used ram: 11900
Tasks: NETWORK(ready,572) HEAT(blocked,1232) MAIN(running,3800) IDLE(ready,160)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:59 ago, cause: power up
Last software reset at 2020-04-26 14:47, reason: User, spinning module GCodes, available RAM 11380 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 29.8, current 29.9, max 30.9
Supply voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-04-26 17:04:27
Cache data hit count 352585371
Slowest loop: 7.03ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 78.60ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 2c:3a:e8:0b:02:f1
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 14584
WiFi IP address 192.168.1.137
WiFi signal strength -64dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

I have a corsair 800 watt atx that I hooked up, about to start another print, ill let ya know if it resets again.