4_1552943590416_homez.g 3_1552943590415_homey.g 2_1552943590415_homex.g 1_1552943590415_homedelta.g 0_1552943590414_homeall.g

Here you go!

I have the bltouch at ~8.3 mm from the glass to the shell. It is a bltouch smart.

When I issue a g28 z the bltouch does not deploy and the nozzle hits the bed.

My Z endstop exists and is attached to the board; however it doesn't indicate as triggered on the machine properties tab. (x and y do)

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.0(RTOS) (2018-06-05b3)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1
The printer is a Cartesian Makerfarm 'pegasus'. The bltouch is authentic.
The commands:

M280 P7 S160 I1; Alarm Release and Push-Pin UP
M280 P7 S10 I1; Pin Down-- Send PWM channel 7 the s10 (angle) command
M280 P7 S90 I1; pin up --Send PWM channel 7 the S90 (angle) command
M280 P7 S120 I1; self test -- Send PWM channel 7 the S10 (angle) command

work correctly.

My config.g:
0_1552929052793_config.g

@z97froehlich said in M106 questions on p1 and p2:

M106 P1 S0 I0 F500 H-1

Odd... p2 worked but never p0.. I'll leave this as unsolved for a day or two. No a big deal, but puzzling.

RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.0(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-06-05b3

When I plug my print cooling fan into P0, it doesn't respond to
m106 P0 S255 (or s1).
When I plug that fan into one of the 'always on' connections, it does turn (correct direction)

The Hot end fan (p1) will turn on with m106 P1 s255 i1 (or s1)

This is the fans section of my config.g:
; Fans
M106 P0 S255 B5 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S255 B5 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
(I do see the 'burst' of 5 seconds on p1)

Both fans are two wire.

The Duet is a pretty recent purchase and I am still working my way through it. I have a e3d v6 hot end (but not with the original fan, should be similar though)

Chip Kigar

Thank you for all that responded. The heated bed is on a relay, however I have ordered a separate but identical power supply to dedicate to the bed.

On to assembling the plugs with my crimper and those dang tiny pins.

I have a makerfarm pegasus 12, a Cartesian printer with 2 Z-axis motors and a 12v 12x12" heated bed

I have read over the motor selection and power supply documentation and did not.. achieve an understanding.

My question is whether this power supply and motor combination will work and what I should know about my setup. Additionally, I am currently using a RAMPS 1.4 controller. Is there any mapping between the motor wiring on the RAMPS to the DUET WIFI?
Will this setup work 'as is'? Do I need to upgrade the power? Upgrade the motors? I am willing to accept less than ideal performance (speed) to save a few $.

. The power supply is
Meanwell MODEL LRS-350-12
DC VOLTAGE 12v
RATED CURRENT 29 amps
CURRENT RANGE 0 – 29 amps
RATED POWER 348 watts
And the motors specification is

Thank you