Hello @dc42 ! Im found bug in Duet WiFi: 1.23 latest firmware. When im use M302 P1 to enable cold extrusion. Buttons for extrusion still locked
Best posts made by ffnull
-
DWC cold extrusion bug
Latest posts made by ffnull
-
DWC cold extrusion bug
Hello @dc42 ! Im found bug in Duet WiFi: 1.23 latest firmware. When im use M302 P1 to enable cold extrusion. Buttons for extrusion still locked
-
RE: Micromake D1 Delta Zprobe doesnt work
@SIam lol. im dont scroll down. Found!
Z probe types 4, 6 and 7 are no longer supported. Instead, use type 5 (filtered digital) or 8 (unfiltered digital) and use the C parameter to specify the input. Note, if your Z probe is connected to the Z endstop input, in RRF 3.0 on Duet 2 boards only (not in RRF 3.01 and later, and not in RRF 3.0 on Duet 3), that input is by default pre-assigned to be used by the Z endstop, so you must free it up first.
Will try
-
RE: Micromake D1 Delta Zprobe doesnt work
@SIam you not right. Its endstop. They works great. Zprobe doesnt work
M558 X0 Y0 Z0 P6 I1
-
Micromake D1 Delta Zprobe doesnt work
Hello. Im installing duet 2 wifi in my Micromake D1. Zprobe here is microswitch. But it doesnt work in firmware. Switch connected to E1 endstop and configured in config. When im press switch - led lights on board, but firmware ignores it. Im check it via M119.
Here my config.g; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Mar 26 2020 23:17:00 GMT+0200 (Восточная Европа, стандартное время) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Micromake D1" ; set printer name M665 R100 L215 B80 H450 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E663.00 ; set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2) M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 X0 Y0 Z0 P6 I1 ;M558 P4 C3 I1 H5 F120 T6000 ; set Z probe type to switch and the dive height + speeds G31 X0 Y0 Z0.050 ; set Z probe trigger value, offset and trigger height M557 R85 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S150 ; set temperature limit for heater 0 to 150C M307 H0 B1 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S310 ; set temperature limit for heater 1 to 310C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined M501
RepRapFirmware for Duet 2 WiFi/Ethernet 3.01-RC4 (2020-03-16b1)
DiagnosticsM122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.01-RC4 running on Duet WiFi 1.02 or later Board ID: 08DDM-9FAM2-LW4SD-6J1F4-3S86R-9LWZX Used output buffers: 3 of 24 (7 max) === RTOS === Static ram: 28052 Dynamic ram: 91808 of which 100 recycled Exception stack ram used: 256 Never used ram: 10856 Tasks: NETWORK(ready,836) HEAT(blocked,1244) MAIN(running,1916) IDLE(ready,76) Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:04:50 ago, cause: software Last software reset time unknown, reason: User, spinning module GCodes, available RAM 10656 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 25.7, current 26.3, max 27.0 Supply voltage: min 13.9, current 14.0, max 14.3, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 1970-01-01 00:00:00 Cache data hit count 498759228 Slowest loop: 3.15ms; fastest: 0.12ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 16.16ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 5c:cf:7f:80:dc:d5 WiFi Vcc 3.39, reset reason Unknown WiFi flash size 4194304, free heap 23808 WiFi IP address 192.168.1.27 WiFi signal strength -37dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0
-
RE: Creatbot F430 transformation. Question directly DC42
@dc42 Thank you very much for the answer. The original sensor overheats from the heating table and the camera warms up. The surface is black glossy carbon. Under carbon black glass
-
RE: Creatbot F430 transformation. Question directly DC42
@veti bltouch overgeating from bed, and camera chamber
-
RE: Creatbot F430 transformation. Question directly DC42
I will clarify. The other day, directly in your store, I bought a full set of accessories to replace my relatives. Level sensor, two temperature sensors, main board and screen, as well as laser filament levels. I plan to throw out my own electronics that are buggy and put yours. But I do not want to get it again, the same problems with the sensor.
What i have right now. Its 8-bit with custom source closed marlin.
-
Creatbot F430 transformation. Question directly DC42
Hello. Im recently buy CreatBot F430.Good printer, with excellent mechanics and horror electronics. The main problem at the moment is the fact that the native level sensor (Origina BLTouch) when the camera warms up goes into an endless error until you cool it. Is your optical sensor stable to high temperatures?
-
RE: Duet 3 first-generation prototype giveaway
Hello. I am an experienced user of your products. I already have 4 boards on hand and ordered another one with all the additional options. I will be glad to receive a prototype for changing the motherboard in CreatBot F430