Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. sslouch
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 12
    • Best 1
    • Controversial 0
    • Groups 0

    sslouch

    @sslouch

    1
    Reputation
    1
    Profile views
    12
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    sslouch Unfollow Follow

    Best posts made by sslouch

    • RE: Tevo Little Monster + DuetWiFi + Touch7" (my conversion)

      Exactly what I was looking for. The schema wasn't the issue it was the Tevo control box wiring and this picture is clear. Thanks a lot for your help.

      posted in My Duet controlled machine
      sslouchundefined
      sslouch

    Latest posts made by sslouch

    • RE: Smart Effector Z-Probe No Longer Working

      Haha. That's easy enough. Thanks @dc42! I didn't think it would fit there and hate to admit I didn't even try 🙂 I was able to confirm the z-probe is working again though!

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      Couldn't get it fixed but I finally received a new smart effector yesterday after being out of stock for a while. Unfortunately, they have changed the configuration of the connectors and as a result it can no longer be used as shown in the documentation on Filastruder. They have moved the thermistor connector to the other side of the PCB so now the heat sink fan no longer fits there. The only place it can go is in the front where the print fan is (was). I was using the print fan bracket and print fan duct from @dc42 on thingiverse. Does anyone have any suggestions for a print fan for this new PCB configuration? Thanks!

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      @dc42

      Thanks

      Trace

      R11R --> R13 ~16.6 K Ohms 😞

      R11R --> R14 ~35 Ohms

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      @crynool I am afraid it is the PCB. Unfortunately they appear to be out of stock until mid February 😞
      I found a different mounting adapter that uses the magball mount points instead so I will try when I get a new one. Guess we are down until then.

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      Thanks all.

      @crynool No, it does not flash when you tap hot end.

      @Mike It is the same fan that I have always used with no issues until now.

      @Dougal1957 The tube ends flush with top of adapter/bottom of Nimble.

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      0_1549910802596_IMG_20190211_123004939.jpg

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      Thanks. I used the mounting adapter that Zesty provided on Thingiverse. I did use nylon washers for the 3 M3 screws/nuts on the bottom and the adapter was printed from PLA which was touching the top. I removed it and saw no damage and reconnected it without the extruder attached and still no z-probe 😞

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Smart Effector Z-Probe No Longer Working

      I didn't see anything obvious. Is there something/someplace more specific I should check? Thanks

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • Smart Effector Z-Probe No Longer Working

      Switched over to a Zesty Nimble extruder and now z-probe is not working. Flashes twice when powering up but then nothing. Fails static and dynamic tests and will crash into bed if you try to set z-probe trigger height. Checked all connections and probe has power at connectors. Any thoughts? Thanks

      Duet 2 Wifi
      Delta (started as a tevo little monster)
      E3D Volcano Hot End

      Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
      Firmware Electronics: Duet WiFi 1.02 or later
      Firmware Version: 2.01(RTOS) (2018-07-26b2)
      WiFi Server Version: 1.21
      Web Interface Version: 1.22.6

      posted in Duet Hardware and wiring
      sslouchundefined
      sslouch
    • RE: Tevo Little Monster + DuetWiFi + Touch7" (my conversion)

      Exactly what I was looking for. The schema wasn't the issue it was the Tevo control box wiring and this picture is clear. Thanks a lot for your help.

      posted in My Duet controlled machine
      sslouchundefined
      sslouch