I think I got my answer from the SeeMeCNC forum:

http://forum.seemecnc.com/viewtopic.php?f=77&t=12819&p=110440#p110440

Thanks a lot David.

With best regards
Stephan

Dear David,
Thanks a lot for your suggestions. I will investigate as you have suggested.

I just realise that my ink to 713.maker didn't work in my former post.
Here it is again:

https://713maker.com/rostock/duet-smart-effector-adaptor

I'll post my findings later here again.

Best regards
Stephan

I plan to install a Duet smart effector to my Rostock Max V2 that was previously upgraded from the Rambo 1.3 to a Duet wifi board.

http://forum.seemecnc.com/viewtopic.php?f=77&t=12819&p=110437#p110437

Now a user suggested me to use the Duet smart effector plate instead of the BL touch.

In order to do so, I need

• a Aluminum adapter for the Duet smart effector from https://713maker.com/rostock/duet-smart-effector-adaptor

• The Duet smart effector itself from Duet3D

Do I need more? I'm not sure about the ball cups / arms. I'd like to use the original ones as shown at 713maker.com's adapter plate webpage.

Or is there more I need to install this?

Thanks for a short advice - hope there is some here

@dc42
This answers my question. Thanks a lot for your detailed explanations!

I'm wondering why my trigger height reading from the web UI console window is sometimes different from the Z height at the web UI head position reading (top left in DW screen)

Any explanation?
What reading is now correct?
I've repeated the shown example twice - both time the same readings.
See below:

0_1563050411703_rmv2 2019-07-13 22-35-11.png

Thanks a lot - will check this.

Quick question:
When I set baby stepping e.g. -0.06mm, this isn't indicating in the Z position at the head position Why not?
I would expect that my current position : 0.8mm as layer no.4 of my print would change to 0.74mm?

I have updated by Delta Rostock Max V2 with a Duet Wifi 1.04 and the 7inch screen.
Additionally I printed a new effector plate which is equipped with a BL touch sensor.
I follow all instruction from the Duet Wifi pages how to calibrate the sensor, the bed, the rod length and all other parameters.

So far so good - all works fine and my prints are good.

Still I get the feeling that I'm really not sure when to do what regarding bed level measurements.

G29 is bed mesh leveling - this is understood.

What I don't get is: whats the difference between the G30 commands in my bed.g file and the G32 commands? I've read https://duet3d.dozuki.com/Wiki/Gcode#Section_G30_Single_Z_Probe and so forth
several time, but somehow still it doesn't click with me.
For example :

• Why do I need still need auto calibration when I have the bed mesh level measurement?
• When do I run G32 ? What is different to all the G32 commands in bed.g ?
• When looking at this video: https://www.youtube.com/watch?v=BgkJVgFnPaE&t=1542s the author 'Design Prototyp Test' explains thoroughly the Duet and probing the bed. But still I'm not sure when to change between these commands.
• During calibration I had to enter the 6 parameters like rod length etc. into the config.g file. Are these values now being temporary overwritten with a G32 or G30 command

Can someone describe this in simple words?

Thanks - Every answer is highly appreciated

1_1563006967656_IMG_6328.jpg
0_1563006967655_IMG_6329.jpg

@ozzzzzzy Got it. Thanks for your explanation

@Ozzzzzzy
Can you explain again the purpose of your task? I don't really understand what you are trying to achieve.

Thanks a lot.