@deckingman llegan 24v certamen a duex5
Latest posts made by froma1976
-
RE: Duex5 problema
@froma1976 está sin acabar, pero solo estoy probando los z
-
RE: Duex5 problema
@T3P3Tony ; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.4 on Fri Dec 20 2019 11:16:09 GMT+0100 (hora estándar de Europa central); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M584 X0 Y1 Z2:5:6:7 E3
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1
M569 P5 S1
M569 P6 S1
M569 P7 S1
M350 X256 Y256 Z256 E256 I0 ; configure microstepping without interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X600 Y700 Z500 S0 ; set axis maxima; Endstops
M574 X1 Y1 Z1 S0 ; set active high endstops; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M305 P0 T100000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T500000 B4723 C1.196220e-7 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S450 ; set temperature limit for heater 1 to 450C; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
-
RE: Duex5 problema
@T3P3Tony ok, pero puede ser que la el cable de vaina de 50 pines esté al revés?
-
Duex5 problema
Hola, en duex5 solo me funciona el canal número 7 ,pongo cualquier motor en el 7 y sin problema lo xambio para 5 6,8 o 9 y da fallo de fases desconectadas , siempre cambiando en el m584 y en m569 claro.
-
RE: Hotend mosquito
@sebkritikel si, configurado con el config tool y fuente de 24v el termistor es el de slicer enginier
-
Hotend mosquito
Alguien tiene el problema de que al configurar el hotend mosquito Magnum con la config tool calienta muy despacio después de 250 grados?