@phaedrux
OK, ran the commands - this attached file shows the result...
YAT Log.txt
I did try to put the contents of the file in the body but it got flagged as spam?

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6J1FJ-3SN6T-TS4GJ
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93304 of which 0 recycled
Exception stack ram used: 312
Never used ram: 11776
Tasks: NETWORK(ready,548) HEAT(blocked,1236) MAIN(running,3652) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:23:20 ago, cause: power up
Last software reset details not available
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 20.6, current 20.8, max 21.2
Supply voltage: min 24.1, current 24.2, max 24.2, under voltage events: 1, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 3178467788
Slowest loop: 0.18ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "m122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.17ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- WiFi -
Network state is running
WiFi module is idle
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address e0:98:06:a4:6a:9f
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 28080
Socket states: 0 0 0 0 0 0 0 0

ok
m552 s0
ok
m552 s0m997 s1
ok
m997 s1
Trying to connect at 230400 baud:  success
Erasing 4096 bytes...
Erasing 212992 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
ok
m552 s0
ok
WiFi module started
M587 S"xxxxxxxxxx" P"xxxxxxxxxx"
ok
M552 s1
ok
WiFi reported error: no known networks found
WiFi module is idle
m587
M587: Failed to retrieve network list
ok
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle

m115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2
ok
WiFi reported error: no known networks found
WiFi module is idle
m98 p"addnetwork.g"
M587: Failed to add SSID to remembered list
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
ok
WiFi reported error: no known networks found
WiFi module is idle

Does this information provide any hints as to what I'm not doing/doing wrong?

I have also tried connecting to another network using a completely different router/SSID/password

Thanks,
Tony

@phaedrux
Will send response when I can get to the machine - it is in a different location to which I do not have keys, sigh....

As a matter of interest, are you happy to say which time zone you are in?

Thanks,
Tony

@phaedrux
OK, so I tried using quotes around the lower case characters - you were quite correct - it made no difference whatsoever.

This is the content of the YAT log:
M552 S0
ok
WiFi reported error: no known networks found
WiFi module is idle
M587 S"xxxxxxxxxxxxxxx" P"xxxxxxxxxxx"
ok
M552 S1
ok
WiFi reported error: no known networks found
WiFi module is idle
m552
WiFi module is changing mode
ok
WiFi reported error: no known networks found
WiFi module is idle
m587
M587: Failed to retrieve network list
ok
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle

Which, while the response to the initial M587 S"NetworkID" P"password" command (ok) would seem to suggest things are ok; the response to the subsequent M587 (Failed to retrieve network list) suggests otherwise..

I'm sure I'm missing something, just having trouble seeing what!

Really appreciate the suggestions so far..

Thanks,
Tony

@gloomyandy You are quite correct. I am measuring the voltage using a digital voltmeter. (I do not have access to an Oscilloscope) I had a suspicion that this may not show the variation in voltage because of the PWM. But I did not know enough about the subject to be sure. I will install the PWM to analog converter and measure the output from that.
Thanks for your comments. I think they were helpful.

@jay_s_uk I already have the PWM to analog converter, I’m trying to confirm that when I issue M3 Sxxxx the output actually changes before I connect the converter.

My testing so far has been inconclusive in that changing the value of S does not appear to affect the measured output - it is fully on all the time.

Thoughts, comments?

Hi, trying to set up a duet 2 wifi running RR3.3 to control a spindle on an Ooznest CNC.

If I run these commands:
M950 R1 C"e0heat" L1000
M563 P1 S"Spindle" R1
M3 P1 S1000

When I measure e0heat I get about 24V (dc)

I don't seem to be able to use "M3 P1 Sxxxx" to change the measured voltage on e0heat - it is either 24V or 0v.

I'm sure I'm missing something - can anyone give me hint as to what?

TIA
Tony

@phaedrux One thing I had noticed was that I seemed to get different results executing the commands, - sometimes they appeared to work OK, other times they came back with a negative result,

I must admit, from what I had seen on the forums, I had begun to suspect I have a hardware problem.

I got the Duet about 3 weeks ago as part of an Ooznest Workbee CNC kit - I'll engage with them to get it replaced.

Many thanks for all your assistance - very much appreciated by someone who is trying to get their head around what is, to them a completely new area!

Tony

@phaedrux
OK downloaded and copied the bin files onto the SD Card. Results attached:

YAT Log.txt

Not sure if the wifi actually updated as it just shows 1.02 or later?

@phaedrux
addnetwork.g:

M552 S0
M587 S"xxxxxxxxx" P"xxxxxxxxxxx"
M552 S1

No special characters in the original network, Exclamation mark (!) used in both SSID and password for the second network...

Both networks running at 2.4GHz

@phaedrux
OK, ran the commands - this attached file shows the result...
YAT Log.txt
I did try to put the contents of the file in the body but it got flagged as spam?

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6J1FJ-3SN6T-TS4GJ
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93304 of which 0 recycled
Exception stack ram used: 312
Never used ram: 11776
Tasks: NETWORK(ready,548) HEAT(blocked,1236) MAIN(running,3652) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:23:20 ago, cause: power up
Last software reset details not available
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 20.6, current 20.8, max 21.2
Supply voltage: min 24.1, current 24.2, max 24.2, under voltage events: 1, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 3178467788
Slowest loop: 0.18ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "m122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.17ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8
- WiFi -
Network state is running
WiFi module is idle
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address e0:98:06:a4:6a:9f
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 28080
Socket states: 0 0 0 0 0 0 0 0

ok
m552 s0
ok
m552 s0m997 s1
ok
m997 s1
Trying to connect at 230400 baud:  success
Erasing 4096 bytes...
Erasing 212992 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
ok
m552 s0
ok
WiFi module started
M587 S"xxxxxxxxxx" P"xxxxxxxxxx"
ok
M552 s1
ok
WiFi reported error: no known networks found
WiFi module is idle
m587
M587: Failed to retrieve network list
ok
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle

m115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2
ok
WiFi reported error: no known networks found
WiFi module is idle
m98 p"addnetwork.g"
M587: Failed to add SSID to remembered list
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
ok
WiFi reported error: no known networks found
WiFi module is idle

Does this information provide any hints as to what I'm not doing/doing wrong?

I have also tried connecting to another network using a completely different router/SSID/password

Thanks,
Tony

@phaedrux
Will send response when I can get to the machine - it is in a different location to which I do not have keys, sigh....

As a matter of interest, are you happy to say which time zone you are in?

Thanks,
Tony

@phaedrux
OK, so I tried using quotes around the lower case characters - you were quite correct - it made no difference whatsoever.

This is the content of the YAT log:
M552 S0
ok
WiFi reported error: no known networks found
WiFi module is idle
M587 S"xxxxxxxxxxxxxxx" P"xxxxxxxxxxx"
ok
M552 S1
ok
WiFi reported error: no known networks found
WiFi module is idle
m552
WiFi module is changing mode
ok
WiFi reported error: no known networks found
WiFi module is idle
m587
M587: Failed to retrieve network list
ok
Error retrieving WiFi status message: bad reply format version
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle

Which, while the response to the initial M587 S"NetworkID" P"password" command (ok) would seem to suggest things are ok; the response to the subsequent M587 (Failed to retrieve network list) suggests otherwise..

I'm sure I'm missing something, just having trouble seeing what!

Really appreciate the suggestions so far..

Thanks,
Tony

@dc42 said in Update Duet 2 Firmware without a network:

@speaker2animals said in Update Duet 2 Firmware without a network:

And that is where the 'fun' began, how do you update the SD card without network access?

Your PC or laptop may well have a SD card socket already. If it doesn't, you can get USB adapters for SD cards on Amazon, eBay etc.

Another possibility is to update the main firmware directly to 3.3 using the Erase jumper and Bossa. The WiFi firmware you already have should work with RRF 3.3 and when you have wifi access working, you can upgrade the wifi firmware.

That said, it should be possible to get your board connected via WiFi using your existing firmware 2.03. What is the problem you are having?

Hi, thanks for the quick response.

When I issue the M587 S"networkID" P"password" command I cannot connect to the network (can't remember the exact fail message and I'm not near the machine at the moment).

Since I posted I have seen some information that suggests there may be a problem if either the NetworkID or password have lower case characters? - this is certainly true of one of these elements for the WiFi I am trying to connect to.

I will try again wrapping the lower case chars with single quotes and see if that fixes it.

Again, thanks,
Tony