Posts made by ajdriscod

@engikeneer @jens55 I rebuilt the hot end and replaced the droopy fan mount I'm running a tune now and everything seems to be going smoothly. Thanks for all your help!

@engikeneer im not above a bonehead move like that i'll take another look i have a bunch of these guys that i haven't assembled yet so i'll try one of those

@jens55 No worries. Hey thanks for spending the time to help me out I really appreciate it, I'll keep tinkering.

@jens55 I've been tweaking the m307 non stop so the notes aren't up to date

@jens55 heres my config should have started with posting it

; Configuration file for Duet 3 MB 6HC "Duet_TC_Test_Bed(firmware version 3.3)
; executed by the firmware on start-up
;
;M501
; General preferences
G21 ; Work in millimetres
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M575 P1 B57600 S1 ;Buad Rate
G4 P500

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M569 P0.5 S0 ; physical drive 0.4 goes backwards
M584 X0.0 Y0.1 Z0.2:0.4 E0.3 C0.5 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M350 C16 I1
M92 X80.00 Y80.00 Z800.00 C100 E93.02 ; set steps per mm
M566 X400.00 Y400.00 Z20.00 C2 E200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X35000.00 Y35000.00 Z1200.00 C5000 E5000.00 ; set maximum speeds (mm/min)
M201 X6000.00 Y6000.00 Z500.00 C500 E2500.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 C400 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S120 ; Set idle timeout
M915 P0.5 S3 F1 H400 R0 ; Coupler, stall settings
;M915 P0.0:0.1 S3 F0 H400 R0 ; X / Y Axes, stall settings

; Axis Limits
M208 X0 Y0 Z0 C0 S1 ; set axis minima
M208 X350 Y350 Z400 C500 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"io0.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io0.in
M574 Y1 S1 P"io3.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io3.in
;M574 Z1 S1 P"io4.in" ; configure Z-probe endstop for low end on Z
M574 C1 S3

; Z-Probe
;M950 S0 C"io4.out" ; create servo pin 0 for BLTouch
M558 P8 C"io4.in" H3 F360 T20000 ; set Z probe type to bltouch and the dive height + speeds
;M558 H10 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P200 Z1 ; set Z probe trigger value, offset and trigger height wih gauge block
M557 X15:320 Y15:320 S16:15 ; define mesh grid

M308 S0 P"temp2" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp2
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 R0.178 C617.5 D7.09 S1.00 V23.7 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp0
M950 H1 C"out1" T01 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 R1.878 C174.6 D6.94 S1.00 V23.8
;M307 H1 B0 R2.620 C123.6:122.4 D4.21 S1.00 V23.8 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P1 D0 H1 F0 ; define tool 0
G10 P1 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P1 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool

@jens55 as for dropping the the supply from 24v to 12v idk.

@jens55 the board im using is a duet 3 6ch and the heater for the hot end is on out 1

@jens55 I'm running 24v the board sensors are reading Vin: 23.8v V12: 11.9 and i just checked my receipt from fillistruder and the cartridge from the kit I bought is a 30 amp 24v heater

@jens55 the part cooling fan picture left with the shroud DOES NOT come on unless i mess with the fan control on the main dashboard. the hot end fan pictured on the right and drooping slightly (OK alot) comes on if the hot end gets over 50C

@jens55

@jens55 I was wrong the part end fan is not coming on but the hot end fan is from the very beginning also seems when I unplugged the hotend fan to get a tune it melted slightly...whoops pics coming shortly.

@jens55 maybe i can try a lower frequency? I'm not to familiar with PWM fans

@jens55 I just started tuning and the fan is on its already preventing the hot end from getting above 120c

@jens55 Also, will that 80% fan setting (if that's what I end up going with) be specified in the M307 for the config, or will I have to incorporate that on the fan side of the config. For my other issue is the part cooling fan supposed to come on during tuning? I don't have it set to thermostatic so I'm not sure why it comes on at the specified 50c.

@jens55 Thanks! I'll give that a go and report back.

@jens55 how would that be specified in the m303 command?

@jens55 All the connections for power are secure I'm not exactly excited about the thermistor connection but its connected and reporting a value.

I'm using 24v but did have to modify some of the e3d connectors to work with the duet board but they all seem secure, I've been playing with it since posting I've disconnected all of the fans and got it to tune to 220 but as soon as I plug them back in the tuning goes down the drain.

Update now the hotend won't get up to temp at all I know everything is plugged in correctly I wonder if my old tuning from the Creality hot end is causing this.

Hey all I'm tuning a E3d hotend with the E3d Toolchanger I had tunes a creality hotend that came with an ender 5 with out issue but once i switched to the e3d v6 I haven't been able to get through the tuning cycle. The cooling fan comes on at 50C even when its not supposed to (in the beginning it's my understanding that the tuning cycle starts with no fans) and the hot end cant get over 120c. With out fans the hot end has no problem getting up to temperature. Even the part cooling fan seems to affect hotend temperature. Any Ideas?