@phaedrux I'm not that familiar with using M122. M122 P101 to print the status of an attached Duex just sits there thinking for a few minutes, then spits out "Expander status 0000" . I'm not sure if the plain M122 should show the drives on the duex. It only shows drives 0-4 This is what it shows
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6JKF2-3SJ6N-KA42K
Used output buffers: 1 of 24 (20 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93920 of which 208 recycled
Exception stack ram used: 568
Never used ram: 8396
Tasks: NETWORK(ready,316) HEAT(blocked,1224) MAIN(running,1816) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:14:39 ago, cause: power up
Last software reset at 2021-09-08 21:29, reason: User, spinning module GCodes, available RAM 7852 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 40.4, current 42.0, max 42.5
Supply voltage: min 24.7, current 24.9, max 25.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 2021-09-09 20:03:40
Cache data hit count 1457745491
Slowest loop: 604.68ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 168, MaxWait: 661ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 18, completed moves: 18, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "m122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.62ms; fastest: 0.07ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 3
WiFi firmware version 1.26
WiFi MAC address 48:3f:da:a6:c0:72
WiFi Vcc 3.38, reset reason Unknown
WiFi flash size 2097152, free heap 24400
WiFi IP address 192.168.1.136
WiFi signal strength -51dBm, reconnections 0, sleep mode unknown
Socket states: 0 0 0 0 0 0 0 0
