Hello
i am trying that.
Antoine

Thanks so much!

The bed probing will be fine, and then I keep the printer on with no print and another bed level will be completely off.

I am still getting the e0heat error. In the config override, I only have the PID tune, I can post the file if needed.
I would not be surprised if I have some odd things in the config, I have been tweaking this config for at least 5 years.

Here is home x

G91                ; relative mode
G1 Z1 F600 H2     ; lift Z relative to current position
G1 X-240 F2000 H1  ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 X4 F1000         ; move slowly 4mm in the +X direction
G1 X-5 F1000 H1         ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 Z1 F200  H2      ; lower the head again
G90                ; back to absolute mode

home y

G91                ; relative mode
G1 Z0.5 F200 H2     ; lift Z relative to current position
G1 Y-320 F3000 H1  ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 Y4 F600         ; move slowly 4mm in the +X direction
G1 Y-5 F600 H1         ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 Z-0.5 F200 H2       ; lower the head again
G90                ; back to absolute mode

home z

G91                ; relative mode
G1 Z5 F200 H2        ; raise head 4mm to ensure it is above the Z probe trigger height
G90                ; back to absolute mode
G1 X100 Y150 F3000 ; put head over the centre of the bed, or wherever you want to probe
G30                ; lower head, stop when probe triggered and set Z to trigger height

Example start GCODE

G90
M83
M106 S0
M140 S65
M190 S65
; probe bed
M300 s1500 p500 ; BIP probe starting
G32 ;probe bed
M300 s1500 p500 ; BIP probe ending
; probe bed end
; set temperature
M109 S215
; wipe extruder sequence
G1 X15 Y10 Z0.2  F3000 ; avoid binder clips
G1 X130 E12 F500 ; prime line
G1 X145 F100 ; slow wipe
G92 E0                  ;zero the extruded length
; process P3STEE PLA1.75
; layer 1, Z = 0.240
T0
G1 E-1.4000 F2100
; feature skirt

I corrected the config.g now looking as follow, but still getting some errors unrelated to my issues.

; Configuration file for p3STEEL

; Communication and general
M111 S0                             	; Debug off
M550 pp3steel		; Machine name and Netbios name (can be anything you like)
M552 S1				; Enable WiFi

; misc settings
M555 P2                           	; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes forwards (x)
M569 P1 S1				; Drive 1 goes forwards (Y)
M569 P2 S1				; Drive 2 goes forwards (z)
M569 P3 S0				; Drive 3 goes forwards (e1)
M569 P4 S1				; Drive 4 goes forwards (E2)

; microstepping and homing switch config
M350 X16 Y16 Z16 E16 I1             ; set 16x microstepping with interpolation


M574 X1 S1 P"!xstop"   ; X min active high endstop switch
M574 Y1 S1 P"!ystop"   ; Y min active high endstop switch
M574 Z1 S1 P"zstop"   ; Z min active high endstop switch


; Motor current and acceleration
M906 X1000 Y1200 Z1200 E1200 I30		; Set motor currents (mA) and increase idle current to 60%
M84 S60 ; Set idle timeout

M201 X3000 Y3000 Z15 E3600		; Accelerations (mm/s^2) 
M203 X6000 Y6000 Z100 E1200		; feedrate  (mm/min)
M566 X1800 Y1800 Z180 E300		; Maximum instant speed changes mm/minute
; M210 X5000 Y5000 Z60  			; set hming feedrate

; steps per mm
M92 X79.01 Y76.04 Z3298.92  ; Set axis steps/mm
; M92 E415:415                          ; set extruder 0 and 1 steps/mm
M92 E415



; Thermistors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M950 F0 C"fan0"  ; Fan 0
M140 H0 ; the bed heater is heater 0


M143 H1 S270 ; Set maximum heater temperature to 270C
M143 H0 S115 ; Set maximum heater temperature to 270C



; Tool definitions
M563 P0 D0 H1                       	; Define tool 0 old
M571 P"e0_heat *" S1.0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures



; Z probe and compensation definition
M558 P1 C"^zprobe.in"  X0 Y0 Z1 H5 F500 T3000    ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min
G31 P500 X15 Y3 Z0.40        ; set threshold and offsets (we were at 0.50 BEFORE ADJUSTMENT)

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0                   	; Axis compensation here


M206 X0 Y0 Z0
M208 X0 Y0 Z0 S1 				; set minimum Z
; max travel and origin
M208 X215 Y310 Z200 

;
T0					; select first hot end

M570 H1 P20 T30 

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

diagnostic
```
M98 P"config.g"
Error: Unknown pin name 'e0heat*'
Error: Heater 2 not found
Error: Heater 3 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found

@Phaedrux said in Struggling in setting up the bed compensation:

M122

Hello
So
M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93788 of which 60 recycled
Exception stack ram used: 584
Never used ram: 8660
Tasks: NETWORK(ready,708) HEAT(blocked,1224) MAIN(running,1904) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 03:48:29 ago, cause: software
Last software reset at 2020-12-16 19:01, reason: User, spinning module GCodes, available RAM 8708 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 31.6, current 36.0, max 40.1
Supply voltage: min 13.3, current 13.9, max 14.1, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/1023
Driver 1: ok, SG min/max 0/1023
Driver 2: ok, SG min/max 155/959
Driver 3: ok, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-12-16 22:49:56
Cache data hit count 4294967295
Slowest loop: 87.70ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.5ms, write time 9.6ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 165, MinFreeDm: 85, MaxWait: 5148849ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 3102, completed moves: 3063, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X111.801 Y162.049 E0.0048" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 46.35ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 60:01:94:09:bc:4e
WiFi Vcc 3.44, reset reason Unknown
WiFi flash size 4194304, free heap 23568
WiFi IP address 10.0.0.19
WiFi signal strength -62dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

M98 P"config.g", I think that shows already some issues. i'll look into that.

Warning: M210: Command is not supported
Error: in file macro line 44 column 10: M92: array too long, max length = 1
Error: Unknown pin name 'e0heat*'
16/12/2020 à 22:51:22	Error: Heater 2 not found
Error: Heater 3 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found

and last the home file.

G91                ; relative mode
G1 Z1 F200  H2       ; raise head 1mm
G1 X-240 Y-340 F2000 H1  ; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 X4 Y4 F1200      ; move slowly 6mm in +X and +Y directions
G1 X-5 Y-5 F1000 H1    ; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90                ; back to absolute mode
G1 X105 Y155 F3000
G30                ; lower head, stop when probe triggered and set Z to trigger height

I forgot my settings are as follow
config

; Configuration file for p3STEEL

; Communication and general
M111 S0                             	; Debug off
M550 pp3steel		; Machine name and Netbios name (can be anything you like)
M552 S1				; Enable WiFi

; misc settings
M555 P2                           	; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes forwards (x)
M569 P1 S1				; Drive 1 goes forwards (Y)
M569 P2 S1				; Drive 2 goes forwards (z)
M569 P3 S0				; Drive 3 goes forwards (e1)
M569 P4 S1				; Drive 4 goes forwards (E2)

; microstepping and homing switch config
M350 X16 Y16 Z16 E16 I1             ; set 16x microstepping with interpolation


M574 X1 S1 P"!xstop"   ; X min active high endstop switch
M574 Y1 S1 P"!ystop"   ; Y min active high endstop switch
M574 Z1 S1 P"zstop"   ; Z min active high endstop switch


; Motor current and acceleration
M906 X1000 Y1200 Z1200 E1200 I30		; Set motor currents (mA) and increase idle current to 60%
M84 S60 ; Set idle timeout

M201 X3000 Y3000 Z15 E3600		; Accelerations (mm/s^2) 
M203 X6000 Y6000 Z100 E1200		; feedrate  (mm/min)
M566 X1800 Y1800 Z180 E300		; Maximum instant speed changes mm/minute
M210 X5000 Y5000 Z60  			; set hming feedrate

; steps per mm
M92 X79.01 Y76.04 Z3298.92  ; Set axis steps/mm
M92 E415:415                          ; set extruder 0 and 1 steps/mm



; Thermistors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M950 F0 C"fan0"  ; Fan 0
M140 H0 ; the bed heater is heater 0


M143 H1 S270 ; Set maximum heater temperature to 270C
M143 H0 S115 ; Set maximum heater temperature to 270C



; Tool definitions
M563 P0 D0 H1                       	; Define tool 0 old
M571 P"e0heat *" S1.0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures



; Z probe and compensation definition
M558 P1 C"^zprobe.in"  X0 Y0 Z1 H5 F500 T3000    ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min
G31 P500 X15 Y3 Z0.40        ; set threshold and offsets (we were at 0.50 BEFORE ADJUSTMENT)

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0                   	; Axis compensation here


M206 X0 Y0 Z0
M208 X0 Y0 Z0 S1 				; set minimum Z
; max travel and origin
M208 X215 Y310 Z200 

;
T0					; select first hot end

M570 H1 P20 T30 

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

bed

G28 X0 Y0     ; Home All
G28 Z0        ; Home All
M561                         ; clear any existing bed transform
M557 X20:170 Y20:270 P2:2
M376 H3   ;taper off compensation after 3mm
G29

G1 X10 Y10 F5000               ; move the head to the corner (optional)

All,
I am facing an issue. I have adjusted my bed with a caliper and some jig and it appears to be level from left to right. I use a Mini differential IR sensor.
I have this build surface stick on a glass
[https://www.amazon.co.uk/gp/product/B07JMT8C9R/ref=ppx_yo_dt_b_asin_title_o04_s02?ie=UTF8&psc=1](link url)

When I run a G32, my bed look to have the center well above the left and right.
I created a macro that measure left and right and that gives me the left and right coordinates

G28                         ; home
G30 P0 X20 Y150 H0 Z-99999    ; probe near a leadscrew
G30 P1 X165 Y150 H0 Z-99999 S-1 ; probe near a leadscrew
M84

G28                         ; home
G30 P0 X20 Y150 H0 Z-99999    ; probe near a leadscrew
G30 P1 X165 Y150 H0 Z-99999 S-1 ; probe near a leadscrew
M84

This gives me

12/16/2020, 7:05:05 PM	M98 P"0:/macros/LEADSCREW"
G32 bed probe heights: -0.193 -0.174, mean -0.183, deviation from mean 0.010
12/16/2020, 7:01:26 PM	M999
G32 bed probe heights: -0.258 -0.233, mean -0.246, deviation from mean 0.013

The heat map looks as follow

RepRapFirmware height map file v2, min error -0.371, max error 0.133, mean -0.155, deviation 0.220
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
20.00,170.00,20.00,270.00,-1.00,150.00,250.00,2,2
 -0.371, -0.366
  0.133, -0.017

I can't manage to tweak it. Even, if I manage to get something better, it will fail in next 30 minutes with no print.

Antoine

@dc42 said in duplicate files in macro and setting:

iap4e

1. This solves the issue, I now have

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.0 or 1.01
Firmware Version: 2.02RC6(RTOS) (2018-12-15b2)
WiFi Server Version: 1.21
Web Interface Version: 1.22.5

2. This is solved
3. Ok, so that's not an issue
4. This is solved

Thanks!!

Antoine

All,
I upgraded my DUET WIFI to latest firmware (DUET WIFI BATCH 3).
I now face 4 issues

1. the version is still showing as 1.21 (see below)
2. the files in MACRO, SETTING, and PLA are duplicated like if I was now able to call all the history
3. the web browser complains of a 404 error
   dwc.js:2 GET http://p3steel.local/rr_download?name=0:/sys/oem.json 404 (file not found)
4. diagnostic message requires to disconnect and reconnect to appear

See diagnostic below

=== Diagnostics ===
Used output buffers: 4 of 32 (14 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
Static ram used: 16152
Dynamic ram used: 100440
Recycled dynamic ram: 2192
Stack ram used: 1224 current, 4448 maximum
Never used ram: 7840
Last reset 00:01:04 ago, cause: software
Last software reset at 2018-12-16 22:53, reason: User, spinning module GCodes, available RAM 7888 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 28.9, current 29.7, max 29.9
Supply voltage: min 13.0, current 13.1, max 13.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-12-16 23:10:36
Slowest main loop (seconds): 0.013969; fastest: 0.000046
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 60:01:94:09:bc:4e
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 15216
  WiFi IP address 10.0.0.18
  WiFi signal strength -58dBm, reconnections 0, sleep mode modem
  Socket states: 0 2 0 0 0 0 0 0
  === Expansion ===
  === Diagnostics ===
  Used output buffers: 13 of 32 (24 max)
  === Platform ===
  RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.0 or 1.01
  Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
  Static ram used: 16152
  Dynamic ram used: 100440
  Recycled dynamic ram: 2192
  Stack ram used: 1224 current, 4448 maximum
  Never used ram: 7840
  Last reset 00:01:27 ago, cause: software
  Last software reset at 2018-12-16 22:53, reason: User, spinning module GCodes, available RAM 7888 bytes (slot 3)
  Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
  Error status: 0
  Free file entries: 10
  SD card 0 detected, interface speed: 20.0MBytes/sec
  SD card longest block write time: 0.0ms
  MCU temperature: min 29.2, current 29.5, max 29.7
  Supply voltage: min 13.1, current 13.1, max 13.2, under voltage events: 0, over voltage events: 0
  Driver 0: standstill, SG min/max not available
  Driver 1: standstill, SG min/max not available
  Driver 2: standstill, SG min/max not available
  Driver 3: standstill, SG min/max not available
  Driver 4: standstill, SG min/max not available
  Date/time: 2018-12-16 23:10:59
  Slowest main loop (seconds): 0.180053; fastest: 0.000112
  === Move ===
  MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
  Scheduled moves: 0, completed moves: 0
  Bed compensation in use: none
  Bed probe heights: 0.000 0.000 0.000 0.000 0.000
  === Heat ===
  Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
  Heater 1 is on, I-accum = 0.0
  === GCodes ===
  Segments left: 0
  Stack records: 2 allocated, 0 in use
  Movement lock held by null
  http is idle in state(s) 0
  telnet is idle in state(s) 0
  file is idle in state(s) 0
  serial is idle in state(s) 0
  aux is idle in state(s) 0
  daemon is idle in state(s) 0
  queue is idle in state(s) 0
  autopause is idle in state(s) 0
  Code queue is empty.
  === Network ===
  Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
  HTTP sessions: 1 of 8
• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 60:01:94:09:bc:4e
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 16680
  WiFi IP address 10.0.0.18
  WiFi signal strength -57dBm, reconnections 0, sleep mode modem
  Socket states: 4 2 0 0 0 0 0 0
  === Expansion ===

Thanks
I have ordered some terminal block which should come soon.
Antoine

Hello
Thanks
I will change the connector.
How can I check that nothing else is burnt?
As said the voltage was showing 0.

Antoine