Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. asafo
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 6
    • Best 0
    • Controversial 0
    • Groups 0

    asafo

    @asafo

    0
    Reputation
    1
    Profile views
    6
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    asafo Unfollow Follow

    Latest posts made by asafo

    • RE: First print - very slow speed ...

      @engikeneer
      WOW..F....K.......I just moved from my skr1.3
      I forgot to change this......
      Thanks
      going to try it

      posted in General Discussion
      asafo
      asafo
    • RE: First print - very slow speed ...

      @cosmowave
      I dont have file called start.g in my system file, but in my prusaSlicer...the pre G code is:
      ;G28 ; home all axes
      ;G1 Z5 F5000 ; lift nozzle
      M220 S100 ; reset speed factor to 100%
      M221 S100 ; reset extrusion rate to 100%
      G90 ; use absolute coordinates
      M83 ; extruder relative mode
      ; Set the heating
      M104 S160 ; set nozzle print temp to 160 for pre-print leveling to prevent oozing
      M140 S[first_layer_bed_temperature] ; set heatbed temperature
      ; Wait for final bed heating
      M190 S[first_layer_bed_temperature] ; wait for the bed to heat up
      ;; Bed Leveling
      ;G32 ; True Bed Leveling
      ;G1 Z5 F5000 ; move z up little to prevent scratching of surface
      ;G1 X3 Y3 F5000 ; go print area
      ;;Set Nozzle Temp
      M109 S[first_layer_temperature] ; wait for the nozzle to heat up
      ; Return to prime position, Prime line routine
      G28
      G1 Z0.2 F3000 ; lower nozzle to printing height
      G92 E0.0 ; reset extrusion distance
      G1 X150 E15 F1000 ; prime nozzle
      G1 X210 F500 ; Slow wipe
      G1 E0.2 F1500; de-retract
      G92 E0.0 ; reset extrusion distance

      posted in General Discussion
      asafo
      asafo
    • First print - very slow speed ...

      Hi Guys,
      First time with duet(duet2 wifi)
      Just finish to calibrate all tempture/estep….homing (I hope, have gear motor on my Z)
      when homing everything looking OK speed is 30mm/s
      When taking benchy from my prusa slicer(speed is around 30-70mm/s)
      Its starting to move slowly around 1-8 mm/s ……why?
      Missing something?
      Thanks
      P.S
      firmware 3.3
      config (3).g

      ; Configuration file for Duet WiFi (firmware version 3.3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.2 on Fri Sep 10 2021 08:45:36 GMT+0300 (Israel Daylight Time)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"SK-GO2" ; set printer name
      M669 K1 ; select CoreXY mode

      ; Network
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ;Ernst Drives
      ;M569 P0 S1 D2 ; physical drive 0 goes backwards using default driver timings
      ;M569 P1 S1 D2 ; physical drive 1 goes backwards using default driver timings
      ;M569 P2 S1 ; physical drive 2 goes forwards using default driver timings
      ;M569 P3 S0 ; physical drive 3 goes forwards using default driver timings
      ;M569 P4 S1 ; physical drive 4 goes backwards using default driver timings
      ;M569 P5 S1 ; physical drive 5 goes forwards using default driver timings
      ;M584 X0 Y1 Z2:4:5 E3 ; set drive mapping
      ; ==========Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes forwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X200.00 Y200.00 Z3200.00 E408 ; set steps per mm
      M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X30000.00 Y30000.00 Z450.00 E6000.00 ; set maximum speeds (mm/min)
      M201 X2000.00 Y2000.00 Z100.00 E2000.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z600 E550 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout
      ;;M671 X-13:-13:323 Y20:250:140 S50 ; set z drive coordinates
      ;;M350 X16 Y16 Z16:16:16 E16 I1 ; configure microstepping with interpolation
      ;;M92 X200.00 Y200.00 Z160.00 E420.00 ; set steps per mm
      ;;M566 X600.00 Y600.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
      ;;M203 X30000.00 Y30000.00 Z2400.00 E2400.00 ; set maximum speeds (mm/min)
      ;;M201 X2000.00 Y2000.00 Z200.00 E2000.00 ; set accelerations (mm/s^2)
      ;;M906 X800 Y800 Z600 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
      ;;M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X305 Y305 Z340 S0 ; set axis maxima

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

      ; Z-Probe
      M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
      M557 X15:215 Y15:195 S20 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      M307 H0 B0 R0.413 C530.0 D9.48 S1.00 V24.2

      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M307 H1 B0 R2.328 C205.0 D5.24 S1.00 V24.1
      M143 H1 S250 ; set temperature limit for heater 1 to 250C

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 C"part_fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 C"ext_fan" S1 H1 T40 ; set fan 1 name and value. Thermostatic control is turned on

      ; Tools
      M563 P0 S"main" D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings
      M575 P1 B57600
      M501
      ; Miscellaneous
      T0 ; select first tool

      posted in General Discussion
      asafo
      asafo
    • RE: panelDue version

      @dc42 said in panelDue version:

      M575 P1 B57600

      Thanks
      Display issue+firmware is OK.
      Open problems:
      Fans doesn’t work (0 – part , 1 – heatsink thermostatic I think…E3D V6 volcano part)
      Bed heating failed (too slow warm)

      I will start debug….
      At least 2 is behind me:
      Firmware
      Homing seq – Y endstop is in the Ymax

      posted in General Discussion
      asafo
      asafo
    • RE: panelDue version

      @dc42 Thanks a lot I will try.
      Thanks for the quick respond

      posted in General Discussion
      asafo
      asafo
    • panelDue version

      Hi Guys
      Just bought my first duet2 wifi + 5i panel.
      I have a lot of issue but I will start with the first
      I did update the main board firmware to 3.3, but I have problem with my panel
      I see in the upper of the panel in red connecting….i don’t know if it normal
      But its seems that my panel not sending command, for example
      I can go to "move" to Z+0.5 the touch is OK but nothing happened…..
      So I though….lets update panelDue firmware(now its 1.24)..
      I tried to do this but got error in DWC "error: m997 aux port 0 ……"
      So no firmware update…..
      Question:
      What is my panel duet version? How can I know?
      Or I have other problem?

      P.S I am connected with 4 pin cable…..
      My main board version is v1.04c ( this data was in the main board box….but not for the panel)
      Thanks

      posted in General Discussion
      asafo
      asafo