Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. baesjerker
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 30
    • Best 1
    • Controversial 0
    • Groups 0

    baesjerker

    @baesjerker

    1
    Reputation
    1
    Profile views
    30
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    baesjerker Unfollow Follow

    Best posts made by baesjerker

    • RE: Ender 3 Pro configuration

      Now everything seems to be working like it was when using my stock Ender 3 Pro board.

      Print quality is more or less the same, maybe a bit worse than before, but I need to experiment a little more with the duet config and in Cura.

      But the stepper motor noise is almost gone they are so much quieter now!

      I also had to lower the current for the stepper motors. They where running really hot using stock (x, y, z, e) (725, 725, 725, 900). Trying to find the magic numbers here.

      I see everything from 400 to 900 on this forum.

      posted in Tuning and tweaking
      baesjerker
      baesjerker

    Latest posts made by baesjerker

    • RE: Primacreator P120 + Duet Wifi

      @phaedrux sorry about that. Yes I meant power supply. This is my only printer with a lookalike laptop charger. My biggest concern is the amperage. 7 A.

      posted in General Discussion
      baesjerker
      baesjerker
    • Primacreator P120 + Duet Wifi

      Hi. I have a spare Duet 2 WiFi laying around. The stock board on my primacreator P120 died.

      I do not know much about wattage, amps and so on, but I know how to connect/wire everything.

      Would it be possible to use my spare Duet 2 WiFi with the original power cord? It’s rated at 12V 7A.

      Thanks

      posted in General Discussion
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      @dc42 said in Ender 3 Pro configuration:

      @baesjerker said in Ender 3 Pro configuration:

      With those settings the extruder motor is skipping and the black filament i am using now seems to be really thin looking.

      What extruder motor does your printer use, and what extruder motor current have you set in M906? From another post I see that your extruder steps/mm is very low, indicating that you have an ungeared extruder. With that type of extruders, it's usually necessary to run the motor close to its rated current to get enough torque when printing PLA. OTOH if you run it too high, the heat from the motor reaches the filament and softens it, which can also lead to problems.

      It’s the stock Ender 3 Pro extruder motor. I believe it’s called “Creality 3D 42-40”. It has a shaft with a adjustable gear. Current is set to 900 and steps/mm is now around 103. I tried to calibrate it and ended up with that number.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      @phaedrux i printed out a hero me fan duct yesterday and there was almost no stringing.
      So it helped a lot. No, I didn’t change the speed in the config. What do I change there? Match the Cura profile? Thanks.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      @noskillzengineer great. Thank you for explaining everything in more detail. I will try to up the non printing speed and check the results. Looking forward to check out your settings.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      Thanks for the tips. I store my filament in a closed box, but I do not have evadry. Could Silica Gel work as a substitute? I have a high quality calliper. Travel speeds are based on the Cura profile @Phaedrux posted yesterday. I think it was 120 or something.

      Thanks for that one @Phaedrux. It actually removed a lot of the stringing issue. Now it’s so much better.

      I have tried temps from 180 and up to 220. Results is almost the same.

      I will try some more settings in Cura. Trial and error.

      I have filaments from PrimaValue (green), Addnorth (transparent), Polymaker (red) and NinjaTek (white). I also have a no brand local black one.

      No I don’t have extruded pressure advance in my Config. I will check it out.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      With those settings the extruder motor is skipping and the black filament i am using now seems to be really thin looking.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      @dc42 said in Ender 3 Pro configuration:

      M305 P1 T100000 B4148 C2.117e-7

      I will try right away. Thanks.

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      @dc42 I found a video on YouTube. He used those settings. When I tried resistance settings @PaulHew uses, the hot end and bed didn’t get hot enough. What do you think would be best to use here?

      posted in Tuning and tweaking
      baesjerker
      baesjerker
    • RE: Ender 3 Pro configuration

      https://drive.google.com/open?id=1Y_DvW1XYmBW7zMpCKuLv6_RJBqDAOi8L Here is my last profile.

      posted in Tuning and tweaking
      baesjerker
      baesjerker