When I upload the ZIP file from the RRF config tool, I get this error even though I have only uploaded 1 ZIP file.

@Phaedrux

@Phaedrux === Diagnostics ===<LF>RepRapFirmware for Duet 3 Mini 5+ version 3.4.0 (2022-03-15 18:59:15) running on Duet 3 Mini5plus WiFi (standalone mode)<LF>Board ID: JT6ZP-TR6KL-K65J0-409NJ-K1X1Z-Z59LU<LF>Used output buffers: 1 of 40 (15 max)<LF>=== RTOS ===<LF>Static ram: 103684<LF>Dynamic ram: 108912 of which 0 recycled<LF>Never used RAM 26260, free system stack 150 words<LF>Tasks: NETWORK(ready,14.2%,420) HEAT(suspended,0.0%,374) TMC(notifyWait,0.0%,123) MAIN(running,85.0%,459) IDLE(ready,0.0%,29) AIN(delaying,0.8%,273), total 100.0%<LF>Owned mutexes: WiFi(NETWORK) USB(MAIN)<LF>=== Platform ===<LF>Last reset 00:08:43 ago, cause: power up<LF>Last software reset details not available<LF>Error status: 0x00<LF>MCU revision 3, ADC conversions started 524065, completed 524065, timed out 0, errs 0<LF>Step timer max interval 990<LF>MCU temperature: min 29.9, current 30.1, max 30.6<LF>Supply voltage: min 0.9, current 0.9, max 0.9, under voltage events: 0, over voltage events: 0, power good: no<LF>Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/12/12, gc cycles 0<LF>Events: 0 queued, 0 completed<LF>Driver 0: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 1: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 2: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 3: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 4: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 5: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Driver 6: ok, SG min n/a, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0, CC errors 0<LF>Date/time: 1970-01-01 00:00:00<LF>Cache data hit count 1040824569<LF>Slowest loop: 3.64ms; fastest: 0.12ms<LF>=== Storage ===<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 22.5MBytes/sec<LF>SD card longest read time 3.1ms, write time 0.0ms, max retries 0<LF>=== Move ===<LF>DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000<LF>=== MainDDARing ===<LF>Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1<LF>=== AuxDDARing ===<LF>Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1<LF>=== Heat ===<LF>Bed heaters -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0<LF>=== GCodes ===<LF>Segments left: 0<LF>Movement lock held by null<LF>HTTP is idle in state(s) 0<LF>Telnet is idle in state(s) 0<LF>File is idle in state(s) 0<LF>USB is ready with "M122" in state(s) 0<LF>Aux is idle in state(s) 0<LF>Trigger is idle in state(s) 0<LF>Queue is idle in state(s) 0<LF>LCD is idle in state(s) 0<LF>SBC is idle in state(s) 0<LF>Daemon is idle in state(s) 0<LF>Aux2 is idle in state(s) 0<LF>Autopause is idle in state(s) 0<LF>Code queue is empty<LF>=== CAN ===<LF>Disabled<LF>Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 18 (min 18), ts 0/0/0<LF>Tx timeouts 0,0,0,0,0,0<LF>=== Network ===<LF>Slowest loop: 201.76ms; fastest: 0.06ms<LF>Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions<LF>HTTP sessions: 0 of 8<LF>- WiFi -<LF>Network state is active<LF>WiFi module is connected to access point <LF>Failed messages: pending 0, notready 0, noresp 3<LF>WiFi firmware version 1.26<LF>WiFi MAC address c4:5b:be:46:87:55<LF>WiFi Vcc 3.38, reset reason Power up<LF>WiFi flash size 2097152, free heap 26456<LF>WiFi IP address 192.168.0.101<LF>WiFi signal strength -48dBm, mode 802.11n, reconnections 0, sleep mode modem<LF>Clock register 00002002<LF>Socket states: 0 0 0 0 0 0 0 0<LF>ok<LF>

@Phaedrux === Diagnostics ===<LF>RepRapFirmware for Duet 3 Mini 5+ version 3.4.0 (2022-03-15 18:59:15) running on Duet 3 Mini5plus WiFi (standalone mode)<LF>Board ID: JT6ZP-TR6KL-K65J0-409NJ-K1X1Z-Z59LU<LF>Used output buffers: 1 of 40 (40 max)<LF>=== RTOS ===<LF>Static ram: 103684<LF>Dynamic ram: 108912 of which 0 recycled<LF>Never used RAM 26260, free system stack 145 words<LF>Tasks: NETWORK(ready,8.1%,368) HEAT(notifyWait,0.0%,374) Move(notifyWait,0.0%,363) CanReceiv(notifyWait,0.0%,942) CanSender(notifyWait,0.0%,372) CanClock(delaying,0.0%,339) TMC(notifyWait,0.0%,123) MAIN(running,90.3%,566) IDLE(ready,0.8%,29) AIN(delaying,0.8%,273), total 100.0%<LF>Owned mutexes: USB(MAIN)<LF>=== Platform ===<LF>Last reset 00:00:26 ago, cause: power up<LF>Last software reset details not available<LF>Error status: 0x04<LF>MCU revision 3, ADC conversions started 26944, completed 26942, timed out 0, errs 0<LF>Step timer max interval 744<LF>MCU temperature: min 21.6, current 25.5, max 25.7<LF>Supply voltage: min 0.4, current 0.9, max 1.0, under voltage events:[Warning: Maximal number of characters per line exceeded! Check the line break settings in Terminal > Settings > Text or increase the limit in Terminal > Settings > Advanced.]

@Phaedrux Emergency Stop! Reset the controller to continue.<LF>ok<LF>

@jay_s_uk What do I need to put on the sd card?

When I input M552 in YAT, It says that "Network related commands are not supported when using an attached single board computer", but I don't have one attached.