@siam thanks, that did it. Now i only need to find a spot where it triggers good enough for the bed but not while moving

Hi,

i just installed a piezo probe for my z-probe but i don't quite get it to do what i want.
The probe is working but reversed. untriggered it is at 1000 and when triggered goes down / to zero.

So in essence it should be fine but i do not understand how to tell the board to just take the 1000 as standard and accept a lower signal as trigger. Also invertion with the I1 or I0 doesn't change it. Changing polarity on the piezo did not change it either.

Anyone got any idea where i am going wrong?

Z-Probe
M558 P3 C"^zprobe.in" I0 R0.4 F300 X0 Y0 Z0                 ; Set Z probe type to switch and the dive height + speeds
G31 X0 Y0 Z-0.1 P600                    					; Set Z probe trigger value, offset and trigger height_text

as said i tried P1, P3, I0, I1,
changed polarization. Anything i forgot?

@phaedrux i know that now. It worked though because my endstops were wrongfully configured as low end for the last year. Don't ask me though WHY it worked that way.

By the way: Its all working properly now. Thanks alot all of you!

I will be back in time probably since i am currently installing my new Duet 3 into my second printer.

@joergs5 yes. My current probe is manually attached but centered directly below the nozzle.

i know that the current z-pos cannot be saved but before i made your change with the endstops even the homed height was gone after every power off. That is working now

@Phaedrux since i corrected the endstop position to be top side z height is not even saved within a power cycle. As an example: I moved the printer to z=0 after homing and it was 20mm above the bed. So i put g92 z25 -> moved it down until it was the correct height, put g92 z0 in, then M500 and homed. But after the homing z0 was again 20mm above the bed. So even in the power cycle it did not remember the new z0 height and instead set the original homed height after homing.

@joergs5 thats true. I changed it but i wonder why it worked for so long.

OK now i got a different problem. Now it ALWAYS sets height after homing to the original homed height but does not save the z- value after g30

@capmjk update:

calibration now also needs to be done after every bootup. else the heightmap is wrong

@phaedrux
No it tells me that no axis is homed.
M119 tells me that all endstops are working properly.
I have to run a delta calibration after every boot at the moment, else it doesn't print correctly.

Have removed G29 S1 from config.g.

Still weird stuff. Have to zero x and y every time after boot. Its driving me mad even though its only 2 quick commands.

The problems arose before i updated the firmware, came out of the blue.

Well yesterday of my belts ripped so i replaced all of them. I think my printer just punishes me for organizing a second one and buying a duet 3 for the new one.

@phaedrux
in the past when the printer homed it set the height after homing to homed height (the one in the config). Now it seems the printer thinks on power on he is homed, then adds the height he travels upwards while homing the first time and adds it ontop.
Then of course he ends up at z=600-800 something and can't travel anymore because he is higher than the maximum z-height i have configured.

@phaedrux

; bed.g
; called to perform automatic delta calibration via G32
;
; generated by RepRapFirmware Configuration Tool v2 on Mon Apr 08 2019 07:52:58 GMT+0100 (British Summer Time)
M561 ; clear any bed transform
G28  ; home all towers
; Probe the bed at 6 peripheral and 6 halfway points, and perform 6-factor auto compensation
; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
G30 P0 X0 Y169.9 H0 Z-99999
G30 P1 X147.14 Y84.95 H0 Z-99999
G30 P2 X147.14 Y-84.95 H0 Z-99999
G30 P3 X0 Y-169.9 H0 Z-99999
G30 P4 X-147.14 Y-84.95 H0 Z-99999
G30 P5 X-147.14 Y84.95 H0 Z-99999
G30 P6 X0 Y84.9 H0 Z-99999
G30 P7 X73.53 Y42.45 H0 Z-99999
G30 P8 X73.53 Y-42.45 H0 Z-99999
G30 P9 X0 Y-84.9 H0 Z-99999
G30 P10 X-73.53 Y-42.45 H0 Z-99999
G30 P11 X-73.53 Y42.45 H0 Z-99999
G30 P12 X0 Y0 H0 Z-99999 S6
; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)
G29
M500

I only had to do a g30 in the past when i changed something like a nozzle. But now it seems i need to set x,y,z manually to zero after every startup.

i got rid of the G29 S1 although its strange that is has been in there for ages without a prior problem.

@phaedrux

Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Feb 26 2019 21:31:01 GMT+0000 (Greenwich Mean Time)

; General preferences
G90                                         				; Send absolute coordinates...
M83                                         				; ...but relative extruder moves

; Delta Settings
M665 L440.000 R227 H434.70 B185.0				; Set delta radius, diagonal rod length, pr. radius and homed height
M666 X0 Y0 Z0 A0.00 B0.00               			     	; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"Anycubic Predator"                     				; Set machine name
M551 P"6154"                         						; Set password
M552 S1					                        			; Enable network and acquire dynamic address via DHCP
M586 P0 S1                                  				; Enable HTTP
M586 P1 S0                                  				; Disable FTP
M586 P2 S0                                  				; Disable Telnet

; Drives
M569 P0 S1                                  				; Drive 0 goes forwards
M569 P1 S1                                  				; Drive 1 goes forwards
M569 P2 S1                                  				; Drive 2 goes forwards
M569 P3 S0                                  				; Drive 3 goes forwards
M584 X0 Y1 Z2 E3											; Drive Mapping
M350 X16 Y16 Z16 E16 I1                     				; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E402.25             				; Set steps per mm
M566 X1000 Y1000 Z1000 E1000    	            			; Set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z12000.00 E10000 					; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z3000.00 E3000.00    				; Set accelerations (mm/s^2)
M906 X1200.00 Y1200.00 Z1200.00 E1000.00 I30 				; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     				; Set idle timeout

; Retraction
M207 S4.0 F5000 R-0.025 T2500 Z0.5							; Firmware retraction

; Axis Limits
M208 Z0 S1                                  				; Set minimum Z

; Endstops
M574 X1 S1 P"xstop"											; configure active-high endstop for high end on X via pin xstop
M574 Y1 S1 P"ystop"                                 		; configure active-high endstop for high end on Y via pin ystop
M574 Z1 S1 P"zstop"                                 		; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M558 P5 C"e0stop" H5 F120 T6000                       				; Set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z16.5                     					; Set Z probe trigger value, offset and trigger height
M557 R115 S20                               				; Define mesh grid
G29 S1														; Load the heightmap

; Bed Heater
M308 S0 P"bedtemp" Y"thermistor" T100000 B4300 C0 			; Set thermistor + ADC parameters for heater 0
M950 H0 C"bedheat" T0                               		; create bed heater output on bedheat and map it to sensor 0
M307 H0 A137.8 C533.3 D1.5 V24.3 B0                       	; Disable bang-bang mode for the bed heater and set PWM limit
M140 H0														; Map to H0
M143 H0 S120  												; Set temperature limit for heater 0 to 120C


; Hotnend Heater
M308 S1 P"e0temp" Y"thermistor" T100000 B4300 C0 R4700		;PT100 Temperature Sensor
M307 H1 R2.925 C140.8 D8.36 S1.00 V24.1						; Autotuned PID parameters
M950 H1 C"e0heat" T1                                		; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S245                                				; Set temperature limit for heater 1 to 240C

; Fans
M950 F0 C"fan0" Q500                                		; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                    							; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                		; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                                   		; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                                		; create fan 2 on pin fan2 and set its frequency
M106 P2 S0 H-1		                                 		; set fan 1 value. Thermostatic control is turned on

;M106 P0 S0 I0 F500 H-1                    					; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
;M106 P1 S1 I0 F500 H1 T45                   				; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
;M106 P2 S0 I0 F500 H-1 										; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 S"Hotend1" D0 H1 F0:2                             				; Define tool 1
G10 P0 X0 Y0 Z0                             				; Set tool 1 axis offsets
G10 P0 R0 S0                                				; Set initial tool 1 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured
;M572 D0 S0.1												; Pressure Advance
;M591 D0 P2 C4 S1											; Activate filament sensor
M404 N1.75 D0.4													; Set for print monitor
M592 D0 A0.07772 B-0.00029 									; Nonlinear extrusion. Set parameters for extruder drive 0

; Miscellaneous
M501                                               			; Load saved parameters from non-volatile memory

; config-override.g file generated in response to M500 at 2022-02-04 15:29
; This is a system-generated file - do not edit
; Delta parameters
M665 L440.000:440.000:440.000 R227.398 H434.408 B185.0 X-0.143 Y0.142 Z0.000
M666 X0.641 Y-0.168 Z-0.473 A0.00 B0.00
; Heater model parameters
M307 H0 R0.258 C533.300:533.300 D1.50 S1.00 V24.3 B0 I0
M307 H1 R2.429 C140.000:140.000 D5.50 S1.00 V0.0 B0 I0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Tue Feb 01 2022 11:56:19 GMT+0100 (Mitteleuropäische Normalzeit)
G91                       ; relative positioning

G1 H1 X505 Y505 Z505 F3000 ; move all towers to the high end stopping at the endstops (first pass)
G1 H2 X-10 Y-10 Z-10 F1800   ; go down a few mm
G1 H1 X15 Y15 Z15 F600    ; move all towers up once more (second pass)
G1 H2 X-25 Y-25 Z-25 F6000              ; move down a few mm so that the nozzle can be centred
G90                       ; absolute positioning
G1 X0 Y0 F6000            ; move X+Y to the centre

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6J9F6-3SJ6N-1A2GK
Used output buffers: 3 of 24 (13 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 74664 of which 12 recycled
Never used RAM 15864, free system stack 134 words
Tasks: NETWORK(ready,13.7%,244) HEAT(delaying,0.0%,314) Move(notifyWait,0.1%,313) MAIN(running,85.8%,441) IDLE(ready,0.3%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:05:05 ago, cause: power up
Last software reset at 2022-02-04 15:15, reason: User, GCodes spinning, available RAM 15864, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 30.2, current 35.7, max 36.1
Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 65090, standstill, SG min/max 0/214
Driver 1: position 65089, standstill, SG min/max 0/223
Driver 2: position 65089, standstill, SG min/max 0/191
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-04 19:57:33
Cache data hit count 4294967295
Slowest loop: 9.85ms; fastest: 0.15ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 2.1ms, max retries 0
=== Move ===
DMs created 83, maxWait 110763ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 8, completed moves 8, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 25.86ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address e0:98:06:22:e6:1d
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24792
WiFi IP address 192.168.178.38
WiFi signal strength -39dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 4 0 0 0 0 0 0 0

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 436C