that blv bed is garbage, Please save your money and buy a better surface. And a bltouch. I got that bed and it is now in the garbage bin. Bed surface that you link too bends when heating up, and that surface is absolutly not working with the ir sensor.

and how di I do pid for bed in rrf3.2?

yep crap it is blown. hope I can find one here

none of my fans are working i gues fuse is blown?

ehm nope still having an issue fans not working on my duet

thanks a lot. it's working again!!!

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Sep 20 2020 12:57:54 GMT+0200 (Central European Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BLV mgn Cube" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; Enable network
M587 S"Bill Wi, the Science Fi" P"sjn8nmdvFyF9" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes backwards blv: its was S1
M569 P1 S1 ; Drive 1 goes backwards blv: its was S1
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M584 X0 Y1 Z2:4 E3 ; Multiple Z; define Drive for Z
M671 X-56.0:373.0 Y171.0:171.0 S5.0 ; Multiple Z; define position of leadscrew for probing Z
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X100 Y100 Z400 E830 ; Set steps per mm for Bondtech.
M566 X400 Y400 Z24 E2000 ; Set maximum instantaneous speed changes (Jerk) (mm/min)
M203 X18000 Y18000 Z800 E2000 ; Set maximum speeds (mm/min)
M201 X3000 Y3000 Z100 E5000 ; Set accelerations (mm/s^2)
M906 X2000 Y2000 Z750 E750 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Pressure advance
M572 D0 S0.05 ; disabled Pressure advance

; Axis Limits
M208 X-23 Y0 S1 ; Set axis minima
M208 X310 Y324 Z360 S0 ; Set axis max

; Endstops
M574 X1 S1 P"xstop" ; Set active high endstops edit: Y endstop is high(max).
M574 Y2 S1 P"ystop" ; Set active high endstops edit: Y endstop is high(max).
M574 Z1 S2 ; Set endstops controlled by probe

; Filament sensor
;591 D0 P1 C3 S1 ; Set Filament sensor Simple type (High) for extruder drive 0, connected to endstop input 3 (E0)

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in"H5 F500 T9000 A5 B0
G31 P25 X36.47 Y-4 Z1.308 ; Set Z probe trigger value, offset and trigger height
M557 X30:270 Y30:270 S40 ; Define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 R4700 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A116.2 C224.5 D5.5 B0 S1 ; Set PID for heated bed values
M140 H0
;M305 P0 T100000 B4092 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; Set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"fan0" Q500
M106 P0 S0 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M950 F1 C"fan1" Q500
M106 P1 S1 H1 T50 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 P2 C"fan2" @500
M106 P2 S2 H1 T50 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue

; Custom settings are not configured
M564 H0 ; Let the Jog buttons work blv: added to allow jog buttons

How to setup heater E1 in rff3.2? I can't get it to work.

Have another question, after calibration and everything saved and M501 in config. Do I have to calibrate everytime a reboot delta? Or can I just run a mesh?

thanks just found it on the duzoki

And how do I set new F value for fans? have delta fans and in my old config I had M106 P0 S0 I0 B0 F6500 H-1 for partcooling fan.

Now it loosk like this M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off