Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. Cinpro
    • Profile
    • Following 0
    • Followers 0
    • Topics 34
    • Posts 174
    • Best 0
    • Controversial 0
    • Groups 0

    Cinpro

    @Cinpro

    0
    Reputation
    2
    Profile views
    174
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Cinpro Unfollow Follow

    Latest posts made by Cinpro

    • RE: DWC layers inaccurate

      test cube is coming up short as well 😞

      40.01 x 40.02 x 39.52

      posted in General Discussion
      Cinpro
      Cinpro
    • RE: DWC layers inaccurate

      https://pastebin.com/CDFjZ74g

      Pastebin of a test cube g-code

      posted in General Discussion
      Cinpro
      Cinpro
    • DWC layers inaccurate

      The layers on my control display incorrectly. I have narrowed it down to S3D by testing other slicers and they report the proper number of layers. it is set to RepRap/Marlin in the slicer on all of these. however on the test print the layer reported below you can see is not 48 layers total. can you guys think of a work around for me? its driving me nuts, it didn't used to do this, and read properly.

      posted in General Discussion
      Cinpro
      Cinpro
    • RE: Crimper (tool) recomendations?

      I have used these on 2 builds and a lot of customizing, well built and worth it.

      https://www.amazon.com/Engineer-PA-21-Universal-Crimping-Pliers/dp/B002L6HJ8W/ref=pd_bxgy_469_3?_encoding=UTF8&pd_rd_i=B002L6HJ8W&pd_rd_r=K5BJTA83QEJ9A5A7J82Y&pd_rd_w=TPQ29&pd_rd_wg=TRm3g&psc=1&refRID=K5BJTA83QEJ9A5A7J82Y

      posted in Duet Hardware and wiring
      Cinpro
      Cinpro
    • RE: Precision Piezo z probes guide for duet users reference

      I have it set like in your example, except for the Z1. I don't plan to use it to home since my hot-end parks off to the side and doesn't touch the bed. Just to clarify, you are using the E0 endstop for all the wires, and not the Z-probe socket on the board beside the Panel Due socket?

      posted in Third-party add-ons
      Cinpro
      Cinpro
    • RE: Precision Piezo z probes guide for duet users reference

      I have a bit of a SNAFU on my install. in the DWC it reads 1000 in red. when I use a meter on the PCB it reads the opposite of what is listed in the directions. the Positive reads 10 Kohms and the Negative reads 4.4 Mohms.

      M558 P1 I1 R0.8 F300 X0 Y0 Z0 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
      G31 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
      M557 X40:285 Y20:310 S20 ; Define mesh grid

      on the Duet board I am plugged into the Z-Probe spot +3.3, GND and Z Probe IN

      posted in Third-party add-ons
      Cinpro
      Cinpro
    • RE: Bed.g can I make Y move first, then X

      thanks guys! 😄 I'll give it a go tonight

      posted in Duet Hardware and wiring
      Cinpro
      Cinpro
    • Bed.g can I make Y move first, then X

      I would like to have my first probe point to move the Y and then the X. the reason being is to avoid a bed clip location. can I just reverse them in the Bed.g file?

      posted in Duet Hardware and wiring
      Cinpro
      Cinpro
    • RE: Print cooling fan not coming on

      fan0

      posted in General Discussion
      Cinpro
      Cinpro
    • RE: Print cooling fan not coming on

      M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P2 S0 I0 F255 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

      posted in General Discussion
      Cinpro
      Cinpro