Posts made by crowem

@Phaedrux
Fixed it thank you. Some how the tool settings got unclicked

@jay_s_uk
That is strange it is set up n the config tool

@Phaedrux
Duet Web Control 3.4.1

; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Fri Dec 16 2022 11:47:29 GMT-0600 (Central Standard Time)

; General preferences
G90                                               ; send absolute coordinates...
M83                                               ; ...but relative extruder moves
M550 P"Duet 3"                                    ; set printer name

; Drives
M569 P0.2 S0                                      ; physical drive 0.2 goes backwards
M569 P0.1 S0                                      ; physical drive 0.1 goes backwards
M569 P0.0 S0                                      ; physical drive 0.0 goes backwards
M569 P0.3 S0                                      ; physical drive 0.3 goes backwards
M569 P0.4 S1                                      ; physical drive 0.4 goes forwards
M584 X0.2 Y0.1 Z0.0 E0.3:0.4                      ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1                        ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E95.00:95.00          ; set steps per mm
M566 X1200.00 Y1200.00 Z60.00 E1500.00:1500.00    ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z180.00 E6000.00:6000.00 ; set maximum speeds (mm/min)
M201 X4000.00 Y4000.00 Z20.00 E1000.00:1000.00    ; set accelerations (mm/s^2)
M906 X900 Y900 Z900 E900:900 I30                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                           ; Set idle timeout

; Axis Limits
M208 X-127 Y-92 Z0 S1                             ; set axis minima
M208 X140 Y92 Z160 S0                             ; set axis maxima

; Endstops
M574 X2 S1 P"!io2.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !io2.in
M574 Y2 S1 P"!io0.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !io0.in
M574 Z1 S2                                        ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P1 C"io3.in" H5 F120 T6000                   ; set Z probe type to unmodulated and the dive height + speeds
G31 P990 X-10 Y5 Z1.1                             ; set Z probe trigger value, offset and trigger height
M557 X-95:105 Y-86:90 S10                         ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138      ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                  ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                           ; map heated bed to heater 0
M143 H0 S280                                      ; set temperature limit for heater 0 to 280C
M308 S1 P"temp1" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                                ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                  ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                      ; set temperature limit for heater 1 to 280C
M308 S2 P"temp2" Y"thermistor" T100000 B4138      ; configure sensor 2 as thermistor on pin temp2
M950 H2 C"out2" T2                                ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00                                  ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                      ; set temperature limit for heater 2 to 280C

; Fans
M950 F0 C"out9" Q500                              ; create fan 0 on pin out9 and set its frequency
M106 P0 C"Pi" S0.8 H0 T10                         ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"out5" Q500                              ; create fan 1 on pin out5 and set its frequency
M106 P1 C"Extruder Front" S0 H-1                  ; set fan 1 name and value. Thermostatic control is turned off
M950 F2 C"out8" Q500                              ; create fan 2 on pin out8 and set its frequency
M106 P2 C"Extruder" S1 H0 T10                     ; set fan 2 name and value. Thermostatic control is turned on
M950 F3 C"out7" Q500                              ; create fan 3 on pin out7 and set its frequency
M106 P3 C"duetfan" S0 H0 T10                      ; set fan 3 name and value. Thermostatic control is turned on
M950 F4 C"out6" Q500                              ; create fan 4 on pin out6 and set its frequency
M106 P4 C"Extruder back" S0 H-1                   ; set fan 4 name and value. Thermostatic control is turned off

; Tools
M563 P0 S"Right" H1 F1:4                          ; define tool 0
G10 P0 X0 Y0 Z0                                   ; set tool 0 axis offsets
G10 P0 R0 S0                                      ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"Left" H2 F1:4                           ; define tool 1
G10 P1 X-32.8 Y-0.15 Z0                           ; set tool 1 axis offsets
G10 P1 R0 S0                                      ; set initial tool 1 active and standby temperatures to 0C

; Custom settings
M501

I no longer seem to be able to extrude test some things from the web interface. I know that this was an issues before when i did not have a loaded filament in the interface but now I don't seen an option to load a filament in to enable these options.

Is this a better way to tell

Got an ir probe Yesterday. Ran G29 after setting up everything and did some tweaks to get more constant bed level around the corners. This is my end result. Is this good other than that one corner. Or did I do something wrong?

I just got a Duet 6hc and trying to wire up some 3 pin fans to be controlled. They are either always on if i use the default pinout or if i try to re wire it they do nto turn on at all. I am using these two fans https://www.amazon.com/gp/product/B009NQLT0M/ref=ppx_yo_dt_b_asin_title_o06_s02?ie=UTF8&psc=, https://www.amazon.com/gp/product/B07VVGHTSR/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
both do the same thing.