Hello, I have now the Pressure Advance Command inserted into the Config.
The Bowden there I use are 800mm more or less.
The Extruder are Bondtech Clone’s and Vulcano Hotend’s.

If it’s for someone possible to check my Config.
I have horrible stringing on Printing.

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.5 on Thu Jan 09 2020 09:19:35 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

M667 S1 ; select CoreXY mode

; Network
M551 P"123" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards exturder 0
M569 P1 S1 ; physical drive 1 goes forwards extruder 1
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4257.9 E435.00:435.00 ; set steps per mm (Z4257.90)

M566 X1000.00 Y1000.00 Z150.00 E3200.00:3200.00 ; set maximum instantaneous speed changes (mm/min) E1200.00:1200.00
M203 X6000.00 Y6000.00 Z400.00 E6500.00:6500.00 ; set maximum speeds (mm/min) standard z=400 e=2400
M201 X1800.00 Y1800.00 Z500.00 E3000.00:3000.00 ; set accelerations (mm/s^2) standard=x2000.00 y2000.00
M906 X1000 Y1000 Z1000 E1100:1100 I30 ; set motor currents (mA) and motor idle factor in per cent standart z=1000
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z450 S0 ; set axis maxima

; Endstops
M574 X2 S1 P"!xstop"
M574 Y2 S1 P"!ystop"
M574 Z2 S2
M574 S2 P"exp.4"

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-17.5 Y15 Z2.40 ; set Z probe trigger value, offset and trigger height
M557 X30:350 Y30:350 S40 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4100 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S350 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M308 S2 P"e1temp" Y"thermistor" T100000 B4100 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M143 H2 S350 ; set temperature limit for heater 2 to 280C
M307 H2 B0 S1.00

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H2 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ;Load saved parameters

M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

;Pressure Advance Extruder
M572 D0:1 S0.75:0.75

;FilamentSenoren
M591 D0 P2 C"e0_stop" S1
M591 D0
M591 D1 P2 C"e1_stop" S1
M591 D1

; *** Panic Button
M950 J1 C"exp.4"
M581 P1 T4 C0
M581 P"nil" T"exp.4"

Hello, I have connected a new Fan on the Duex WiFi and now the Fan‘s don’t work anymore.
It’s possible to fix the Board.

Thx 4 the Helping

Now I read in the Doku. the right name of e2stop are exp.e2stop

Are the right code
M950 J1 C"^exp.e2stop”
M581 P0:3 S1 T0 C0

Hello, Now I have install the new Firmware 3.01 RC4.
But the config don’t won’t Trigger or make everything.

M950 J1 C“e2stop“
M581 P0:3 S1 T2 C1

The GCode M582 T2 return nothing.

I make tomorrow the Upgrade.
Thx 4 the help.

The BL-Touch config are the Same.

I have a little bit trouble with my Emergency Stop Button.
So I use the Firmware Version 3.
The wire I have take on Pin "e2stop" and grd.

in my config i have take the code
M581 P"e2_stop" T0 C0

if i write M582 T2 in the console i take Nothink back.

what´s the prob.

i would later a custom scipt to leave the current possition and lower Z

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.5 on Thu Jan 09 2020 09:19:35 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

M667 S1 ; select CoreXY mode

; Network
M551 P"123" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4257.9 E435.00:435.00 ; set steps per mm (Z4257.90)

M566 X1000.00 Y1000.00 Z150.00 E1200.00:1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z360.00 E2400.00:2400.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z500.00 E2000.00:2000.00 ; set accelerations (mm/s^2) standard=x2000.00 y2000.00
M906 X1000 Y1000 Z1200 E1000:1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z450 S0 ; set axis maxima

; Endstops
M574 X2 S1 P"!xstop"
M574 Y2 S1 P"!ystop"
M574 Z2 S2
;M574 e2stop S1

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-17,5 Y15 Z1.30 ; set Z probe trigger value, offset and trigger height
M557 X30:350 Y30:350 S40 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4100 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M308 S2 P"e1temp" Y"thermistor" T100000 B4100 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M143 H2 S280 ; set temperature limit for heater 2 to 280C
M307 H2 B0 S1.00

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H2 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ;Load saved parameters

M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

;FilamentSenoren
M591 D0 P2 C"e0_stop" S1
M591 D0
M591 D1 P2 C"e1_stop" S1
M591 D1

; *** Panic Button

M581 P"e2_stop" T0 C0

Thx, it works
Awesome

Thx 4 the fast helping I wil Do the test tomorrow and report.

Hello, i have connected 2 Simple Filamentsonsors on my Duet3D Board. The Led‘s shows On/Off when I take the Filament into the Sensors but i don’t have a Status Massage in the Webbrowser.
The Trigger always shows that is no triggert.

I use the E0 and E1 endstops

Config.g

M591 P3 C"e0_stop" S1 ; filament monitor connected to E0_stop

What’s going wrong.

thx 4 your help. #
I will change the 2 lines, so i have the same clone bondtech extruder. Now i hope the changes will make all better than bevor.
I print the cube next monday and i post the result.

i have now calibarate the the extruder if i extrude 100mm i take 99,97mm out.