@phaedrux said in Please help me update Duet Web Control:

If you wish to stay with RRF2 you are limited to DWC 2.0.7 as well. In order to move beyond that you'd need to do some updating.

If you still have access to DWC. Upload these 3 zip files, one at a time in the system tab. Don't extract them first. Reboot after each. Use M115 in the gcode console to verify the firmware has been applied.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/Duet2and3Firmware-3.3.zip
That will get your firmware and DWC up to date.

You can see the change logs here:
https://github.com/Duet3D/RepRapFirmware/wiki/Changelog-RRF-3.x

For your config, might be a good idea to run through the configurator tool and generate a fresh set for RRF3.
https://configtool.reprapfirmware.org/Start

Backup your existing config files in the sys folder in case you want to switch back to RRF2. It’s easy to switch back and forth, just upload the zip file for the version you want and then upload your config files.

These documents will come in handy during the conversion.
https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview
https://duet3d.dozuki.com/Wiki/Gcode

Thank you so much for your reply. I appreciate your time helping me.
Is it possible to go back to my current installation if something doesn't work out? I will make a backup of all system files and download the zip before doing anything else.
Thanks again.

Hi and thanks for the help. (I am far from a programmer but can follow instructions.)

Machine details
Board: Duet WiFi 1.02 or later
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)
Duet WiFi Server Version: 1.23
Duet Web Control 2.0.7

I noticed on Github that I am a bit behind with the DWC. But I don't have a clue on how to update it. I can see some files but don't know which ones to upload. I see there is an Upload button in the System menu.
I would really appreciate it if someone could point me to a tutorial or YouTube video on how to do it.

Is it possible to update the board also? From what I understand it is a rather old board. I also don't want to do something where everything on the board is wiped. I don't have a clue on how to get everything working again.
Thanks again.

@Veti
Yes, I have learned that. I am not comfortable doing it myself at this stage. Will do it later some time.

Thanks again. You have been a great help. The think I like for now the most is that I can change the baby-steps' increments.

It says:
Duet Web Control 2.0.7

I'm so happy.

@Veti
Ok, thanks. I have just loaded the file again under ip/reprap.htm

Nothing seemed different. I tried again to load the page but only with IP. And it refreshed to what seems to be the updated DWC.
It looks a whole lot different and will have to learn the new layout ... but I like it.

Thank you so much again for your help. Much appreciated.

@Veti How did you know that? You're a genius. Thanks for sticking with me. I don't mind having it like this, but what did not happen or happen? I want to learn.

It doesn't look like it installed the file:
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.05.1 (2020-02-09b1)
WiFi Server Version: 1.23
Web Interface Version: 1.22.6

@Veti I'm using the printer's IP address. I can successfully ping it and it is also listed as a connected device on router UI.

I tried with Edge, Firefox & Chrome, normal and private/incognito mode and in all instances just a blank page.

I have also switch off and back on the printer a couple of times.

@Veti I unfortunately need to change my reply to: "It worked once but not again". Anything I can try. I cannot even access it from my phone or tablet. Page remains empty. I don't get an error message ... only empty page.

The wifi seems ok. I could start a single layer square which is printing now. Page remains empty.

Any other advice will be most welcome. At the moment I am stuck with an empty page.
If needed, I can access the printer through a USB cable with my Laptop.

@Veti great. Worked first shot. Thanks again.

@Veti do I need to switch off and back on after uploading the file? I just uploaded the file and all were extracted 100%. The page then went completely empty ... I even refreshed the page ... no difference. I don't want to switch off and back on before you giving me the green light.
Thanks.