Posts made by FLSMichael

@elena thats sounds nice i am waiting for new cable then i am going to try that.

@dc42 i have 2 of them both are doing the same, but not with shot cable like 20-30 cm.

@dc42
Duet 6HC to 1XD to the iHSS57 motor with integratet driver.

Hello, here come the problem, i am not shure how to connect the driver alarm.
do you have a sketch?

Hello,
is it possible to use the Alarm Signal from iHSS57 Motor to stop the Printer or Pause the print.

@dc42
ok, i have try now:

but it dont works, motor dont moves! LED goes to permanent RED

when i change EN+ to EN- and i start Homing then LED is permanent RED but motor is also not moving.

I has check the Rev. from my 1XD it is REV.1.0 may is this the prob?

@dc42 ok I will try this

Ok, now my printer is working but of course i didnt connect the EN- this means always on, i cant move x and y when printer is on manual, i am not shure how to conect EN+ and EN- to the 1XD board.

Can i destroy the motor if i change polarisation ? for en+ and en-

@elena
Hello Elena, i was struggeling with nsame problem, i was conecting first in Differential Signal for testing with 25cm long cable and it works without problem, then i was using longer cable around 2m and it didnt work anymore. Even this was a good cable for cain and with shielding.

Now i am using:

and didnt connect Enable + signal and it works.

Hello,
now it looks like the motor works, i simply didnt connect EN-

@elena
yes

@dc42
i will try

@alankilian
HISU adj, i have here is only compatible to HBS57 not HSS57.

@alankilian
good morning, in this Youtubvideo is the HBS57 Driver i have the HSS57 there is no software for it.

@elena
Hello elena,
are your iHSS57 running now?

@alankilian
how do i get access to the register?
what do i need for this? rs232 adapter, but i didnt found software for those HSS57 drivers

@T3P3Tony

Tony, at the 1XD
D0_Step(-) to HSS57 PUL-
D0_Step(+) to HSS57 PUL+
D0_Dir(-) to HSS57 to DIR -
D0_Dir(+) to HSS57 to DIR+
D0_En(-) to HSS57 to ENA-
D0_En(+) to HSS57 to Ena +

The printer is runnig well, but when i go up with speed over 200mm/s there is always the risk that x or y driver is in alarm.

if i slow down the prints i can print nice.
i have 2 IHS57 Stepper here with integrated driver i want to try with them to speed up the prints.

Hello everyone,

Big CoreXY
Printer Board: Duet 3 MB6HC (MB6HC)
Firmware: RepRapFirmware for Duet 3 MB6HC 3.4.5 (2022-11-30)

I'm in need of some help with my 3D printer setup. I'm using Chinese HSS57 drivers with closed-loop NEMA 23 motors on my Creatbot F1000 3D printer 1m X 1m x1m , which has been upgraded with a Duet3 6hc board and two Duet3 1hcl boards for the X and Y axis.

http://cncdrive.com/datasheets/HSS57.pdf

However, I've been experiencing an issue where the HSS57 drivers fail after a few hours of 3D printing, with the drivers blinking 6 times in red. I've tried swapping out both the motors and the drivers, but the issue still persists. Neither the motors nor the drivers are overheating, so I'm not sure what the problem could be.
The print quality is very good and the printer works great up until a certain point that I cannot predict, and it just shuts off

I'm feeling quite frustrated and at a loss for what to do next. If anyone has any recommendations for a set of NEMA 23 motors with integrated drivers, or for the Duet3 1XD, I would really appreciate it. Thank you in advance for your help!

config (2).g