Hi
i have rebuild my Anycubic Chiron with a Duet 3 mini 5+ and now i am wondering if i coud use the old touch display on the duet.
It has normal transmission pins
VSS
RX
TX
RST
5V
is there any chance that i could reuse the old display?
sry for my grammar
@argo said in Duet 3 mini 5+ sensorless homing not working:
M17
G4 P150
thx i implemented it into my Code. But it wasn't the Problem i forgot to set
M569 P0.0 V0
to
M569 P0.1 V0
now it works thx for the Help again
@argo I think i am a bit stupid but i just cant get the code working for the Y achsis
M400
M913 Y75
M915 Y S-15 R0 F0 H200
M569 P0.0 V0
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H2 Y20 F6000
G1 H1 Y-415 F4000 ; move quickly to X axis endstop and stop there (first pass)
;G1 H2 X10 F6000 ; go back a few mm
;G1 H1 X-415 F2000 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
M913 Y100
@frieck ok it works just fine now
thx for the support and the fast ansers
@argo M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3beta2 running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: S6LD7-7396U-D65J0-40KM8-2213Z-RMB7V
thx your code works a litelbit at least it is detecting something now i will try now to tune the crash theshold
config.g
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Big One" ; set printer name
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X700 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X10 Y10 Z0 S1 ; set axis minima
M208 X400 Y400 Z400 S0 ; set axis maxima
; Endstops
M574 X1 S3 ; configure sensorless endstop for low end on X
M574 Y1 S3 ; configure sensorless endstop for low end on Y
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; Z-Probe
M950 S0 C"io1.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io3.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y30 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X25:375 Y25:375 S20 ; define mesh grid
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"out5" Q500 ; create fan 0 on pin out5 and set its frequency
M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out6" Q500 ; create fan 1 on pin out6 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; homex.g
M400
M913 X50
M915 X S-128 R0 F0 H400
M569 P0.0 V10
G4 P200
G91 ; relative positioning
;G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-415 F4000 ; move quickly to X axis endstop and stop there (first pass)
;G1 H2 X5 F6000 ; go back a few mm
;G1 H1 X-415 F360 ; move slowly to X axis endstop once more (second pass)
;G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
M913 X100
M915 S63 X R0
@jay_s_uk i have at the moment the 3.3.0-b2 installed but i tested ist with 3.2.2 and3.2.0 i.
i am rebuilding an old printer so it never worked before i am normally very
experienced with 3d printers
Hi i am having big prolems setting um my sensorless homing with the duet 3 mini 5 + wifi.
if i try to home it it always crashes into the end reguardless of the sensetivity i type in i read many poast but still cant get it to work properly. Any suggestions?