@frnknstn518 So this is where im at. I have Euclid probe and i cant seem to get it to trigger. i checked the wiring, and when connected lights are on. When i press the switch it goes off. How do i set this to work with the probe display in DWC. Probe just stays at zero. Here are some of my g files
; Configuration file for Duet 3 MB 6HC (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sat May 13 2023 19:27:15 GMT-0400 (Eastern Daylight Time)
; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 3" ; set printer name
M669 K1 ; select CoreXY mode
G4 S2 ; Wait for expansion boards to start
; Network
;M552 S1 ;Enable network
;M586 P0 S1 ;Enable HTTP
;M586 P1 S0 ;Disable FTP
;M586 P2 S0 ;Disable Telnet
; ----Z Drive Map----
, ------+------
, | 0.2 | 0.3 |
, |-----+-----|
, | 0.1 | 0.4 |
, ------+------
, FRONT
; Looking at the printer from the top
; Drive directions
M569 P1.0 S1 ; physical drive 1.1 goes forwards Y DRIVE
M569 P1.1 S1 ; physical drive 1.0 goes forwards X DRIVE
M569 P0.1 S1 ; physical drive 0.1 goes forwards FL Z DRIVE
M569 P0.2 S0 ; physical drive 0.2 goes forwards RL Z DRIVE
M569 P0.3 S1 ; physical drive 0.3 goes forwards RR Z DRIVE
M569 P0.4 S0 ; physical drive 0.4 goes forwards RF Z DRIVE
M569 P0121.0 S0 ; physical drive 0.0 goes forwards EXTRUDER DRIVE
; Motor mapping and steps per mm
M584 X1.1 Y1.0 Z0.1:0.2:0.3:0.4 E121.0 ; set drive mapping
M84 S3600 ; motor idle timeout
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z400.00 E690.00 ; set steps per mm
; Drive currents and speeds
M566 X900.00 Y900.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E7200 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E3000.00 ; set accelerations (mm/s^2)
M906 X1600 Y1600 Z1200 E500 I70 ; set motor currents (mA) and motor idle factor in per cent
M84 S120 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z350 S0 ; set axis maxima
; endstops
M574 X2 S1 P"121.io0.in" ; X min active high endstop switch
M574 Y2 S1 P"io5.in" ; Y min active high endstop switch
M574 Z1 S1 P"io6.in" ; Z min active low endstop switch
; Z-Probe (Euclid)
M558 P8 C"!121.io2.in" X0 Y0 Z1 H3F200 T5000 ; K is probe type, P5 for NC switch, C input pin, H is dive height, F is probing speed, T is travel speed, A is number of probes
G31 P500 X 11.0 Y0.5 Z1.65
; Bed leveling params
M671 X-65:-65:365:365 Y0:395:395:0 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right)
M557 X30:270 Y30:270 P5 ; Define bed mesh grid (inductive probe, positions include the Y offset!)
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"BedTemp" ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0 Q10 ; create bed heater output on out0 and map it to sensor 0
M307 H0 R4.843 K1.017:0.000 D1.55 E1.35 S1.00 B0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"121.temp1" Y"thermistor" T100000 B4725 A"NozzleTemp" ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"121.out0" T1 ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 R5.006 K0.971:0.000 D1.64 E1.35 S1.00 B0 V23.9 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"121.out1" Q500 ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500 ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 ; define tool 0
G10 P0 X0 Y0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
T0
; Custom settings are not defined
; ***********************************************************
; Euclid Probe homez.g Example Macro
; RRF3.X Firmware Example
; saveas system/homez.g
; comments and echo statements throughout are provided for convenience
; ***********************************************************
if !move.axes[0].homed || !move.axes[1].homed ; If the printer hasn't been homed, home it
M98 P"0:/sys/homexy.g"
M561 ; clear any bed transform
M290 S0 R0 ; clear baby steps
G91 ; relative positioning
G1 H2 Z6 F6000 ; lift Z relative to current position to clear any obstructions
M400
G90 ; absolute positioning
; echo "Call deployprobe.g macro"
M401 P0 ; This runs macro file deployprobe
; echo "Return"
G1 X175 Y175 F9000 ; go to center of bed in advance of probe that point
M400
; echo "G30 Command"
G30 ; Probe the bed at the current XY position. When the probe is triggered,
; adjust the Z offset of the current tool to make the current position Z=0.
G1 Z10 ; raise Z=10
M400
G4 P500
; echo "Call bed4point.g macro"
M98 P"0:/sys/bed4point.g" ; tram bed
; echo "Return"
G1 X145 Y162.5 F9000 ; go back to the first probe point and reprobe 0 in case it moved
G30
; echo "Call retractprobe.g macro"
M402 P0 ; retract probe
; echo "Return"
G1 Z10 F600 ; lift Z relative to current position
G90 ; absolute positioning
M564 S1 H0 ; reset the bounding limits
; G1 X150 Y0 F9000 ; move carriage to center front
; ***********************************************************
; Euclid Probe Fixed Dock Retract Probe Macro M402
; RRF3.x Firmware Example
; saveas system/retractprobe.g
; comments and echo statements throughout are provided for convenience
; ***********************************************************
echo "running retractprobe.g macro"
; uncomment next line to echo the probe deploy state
; echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
; Dock side position is at X0 Y30
; Docked probe postion is at X0 Y0
; Dock entry/exit point is at X65 Y0 Z10 **USER MUST ESTABLISH EXIT HEIGHT Z
G90 ; absolute positioning
M564 S0 ; allow beyond limit axis to print area
if sensors.probes[0].value[0]!= 0
echo "Probe Value =" ^sensors.probes[0].value[0]
echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
abort "retractprobe: Probe not currently picked up!"
; echo "pass first logic loop"
; uncomment next line to echo the probe value and probe deploy state
; echo "Probe Value =" ^sensors.probes[0].value[0]
; echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
G1 X150 Y350 Z10 F3000 ; move to ready position
G1 X100 Y350 Z10F 3000 ; move to the entry position for the dock
G1 X50 Y350 Z10 F300 ; move into the dock position
G4 P250 ; pause 250 usecs
G1 X50 Y300 Z10 F6000 ; move to the side adjacent to the dock swiping the probe off
M400
; uncomment next line to echo the probe value and probe deploy state
; echo "Probe Value =" ^sensors.probes[0].value[0]
; echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
G1 X175.0 Y175.0 Z10 F6000 ; move to the center of the bed
M400
M564 S1 ; limit axis to print area
; echo "complete movement commands"
if sensors.probes[0].value[0]!= 1000
; echo "Probe Value =" ^sensors.probes[0].value[0]
; echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
abort "retractprobe.g Probe not correctly dropped off in dock!"
M564 H1 S1 ; Restrict movement to within axes boundaries (for normal Y movement)
echo "Macro retractprobe.g complete"
; ***********************************************************
; Euclid Probe Moving Z Dock Deploy Probe Macro M401
; RRF3.X Firmware Example
; saveas system/deployprobe.g
; comments and echo statements throughout are provided for convenience
; ***********************************************************
; echo "Running deployprobe.g"
; if !move.axes[0].homed || !move.axes[1].homed ; If the printer hasn't been homed, home it
; M98 P"0:/sys/homexy.g"
; uncomment next line to echo the probe deploy state
; echo "Object Model Deployuser token =" ^sensors.probes[0].deployedByUser
M564 H0 S0 ; Allow movement BEYOND axes boundaries (for Y to reach probe dock)
G91 ; relative positioning
echo "Lift Z in advance of deploy"
G1 H2 Z15 F3000 ; move Z 15 for clearance above dock.
; ; need to figure out some safety check on this
G90 ; absolute positioning
; echo "Probe Value =" ^sensors.probes[0].value[0]
if sensors.probes[0].value[0]!=1000 ; if sensor is value other than 1000 do this
; uncomment next line to echo the probe deploy state
; echo "deployuser token = " ^sensors.probes[0].deployedByUser
; echo "Probe State = " ^sensors.probes[0].value[0]
abort "deployprobe start value Probe already picked up. Manually return probe to the dock"
; if we're here we know it's because the above is true which I assume is because you have an NC switch as a probe.
; echo "Passed first logic test to deploy probe"
; Dock side position is at X0 Y30
; Docked probe position is at X0 Y0
; Dock exit point is at X65 Y0
G1 X50 Y300 F6000 ; move adjacent to probe dock location
M400 ; wait for moves to finish
G91 ; relative coordinates
G1 Z-15 ; recover the z clearance
; echo "Probe Pickup while loop running"
; uncomment next line to echo the probe deploy state
; echo "Object Model Deployuser token (before while loop) = " ^sensors.probes[0].deployedByUser
G90 ; absolute coordinates
G1 X50 Y350 F3000 ; move over dock
G4 S1 ; pause for pickup
M400 ; wait for moves to finish
while sensors.probes[0].value[0]=1000
; echo "Probe Pickup while loop running"
G91 ; relative coordinates
G1 Z-0.25 F600 ; jog bed up 0.25mm change to suit user preference
M400 ; wait for moves to finish, allow polling interval to trigger and check probe value
G90 ; absolute coordinates
; echo sensors.probes[0].value[0]
; echo iterations
if iterations=100 ; if probe has moved 100*step increment without pickup detection, exit loop
break
G4 P250 ; pause 1/4 seconds
echo "Probe Value =" ^sensors.probes[0].value[0]
G91
G1 Z-0.5 F600 ; move probe down in the dock to clear the roof. adjust as needed
G90
G1 X100 Y350 F1200 ; slide probe out of dock - slowly example exit is to the +X direction
G1 Z10 ; move bed to clear probe from build surface
M400
G4 P250 ; pause 1 seconds
echo "Probe Pickup while loop complete"
; uncomment to echo the probe deploy state
; echo "Object Model Deployuser token (after while loop) = " ^sensors.probes[0].deployedByUser
G90 ; absolute positioning
G1 X175 Y175 F3000 ; move to center of bed for ready position
M400 ; wait for moves to finish
if sensors.probes[0].value[0]!=0
; uncomment to echo the probe deploy state
echo "Object Model Deployuser token (in abort if section)= " ^sensors.probes[0].deployedByUser
abort "Deployprobe endvalue not 0 Probe not picked up! Deploy cancelled."
M564 H1 S1 ; Restrict movement to within axes boundaries (for normal Y movement)
echo "Macro deployprobe.g complete"
