Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. gabrielpf
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 7
    • Best 0
    • Controversial 0
    • Groups 0

    gabrielpf

    @gabrielpf

    0
    Reputation
    1
    Profile views
    7
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    gabrielpf Unfollow Follow

    Latest posts made by gabrielpf

    • RE: Black screen 7i PanelDue black screen

      @phaedrux It is alive again 🙂 Thank you !

      posted in PanelDue
      gabrielpfundefined
      gabrielpf
    • Black screen 7i PanelDue black screen

      Dear all,

      My 7i panel went black during regular use (no firmware update or modified settings). Everything works well via the web interface.
      The backlight is on and there is a yellow light at the bottom. Is the panel defective?

      Thanks20220706_092407.jpg ,

      Gabriel

      posted in PanelDue
      gabrielpfundefined
      gabrielpf
    • RE: How to trigger relay/mosfet board with gcode (5v pins)

      @dc42 what command could i use the get this 3.3V out as a trigger for another device?

      posted in Duet Hardware and wiring
      gabrielpfundefined
      gabrielpf
    • RE: Bed tempetature does not stop increasing

      @phaedrux fcd67400-54dc-45ef-98ac-80e15469b83a-image.png

      Card on the slot but disconnected (checked on the panel due after restarting) ... the issue persists (red light on and 24V between the bed terminals).

      I acquired the duet from https://reprapworld.nl/ last December.

      Is it a common issue? I have the same setup in another printer (not used as often) and I wonder if I should switch to a relay to extend the duet lifespan.

      Thank you all very much for the quick replies.

      posted in Duet Hardware and wiring
      gabrielpfundefined
      gabrielpf
    • RE: Bed tempetature does not stop increasing

      @dc42 said in Bed tempetature does not stop increasing:

      chip are OK, disconnect the bed heater from the Duet, then power up the Duet. If the mosfet is working properly, the bed heater LED on the Duet should be off until you command the bed heater on.

      There is a red light next to the bed heater that is always on (even after restarting) and I measured 24V between the terminals. Just uploaded a photo to the other comment. The cables connected to the duet are no longer connected to the bed (I use an XT60 connector from my control panel).

      posted in Duet Hardware and wiring
      gabrielpfundefined
      gabrielpf
    • RE: Bed tempetature does not stop increasing

      @jay_s_uk ![alt text]20210807_175801.jpg

      I am using a 30x30 cm 24V heating mat connected directly to the duet. The mat specifications say the current is 12.5A which is below the 18A limit for the duet.

      posted in Duet Hardware and wiring
      gabrielpfundefined
      gabrielpf
    • Bed tempetature does not stop increasing

      Hello everyone,

      I have been using my Duet2 wifi for a few months without a problem, but suddenly the bed temperature started increasing and does not stop.

      The problem started near the end of a 72h print. The bed temperature was set to 90deg and was stable for approximately 60h when the duet stopped printing with a warning that the bed temperature was 15deg above the defined value (the temp on display was 107deg). The bed temperature didn't stop increasing (reached 120deg) until I disconnected the cable.

      The only issue is the bed temperature since it keeps printing. I am currently printing PLA keeping the bed heater disconnected.

      Any ideas?

      Thanks

      config.g

      posted in Duet Hardware and wiring
      gabrielpfundefined
      gabrielpf