phaedrux found another m208 in config that overrided the previous settings.. deleted and now works properly

Latest posts made by KAMIKAZE_FREAK
-
RE: Wrong size (solved)
-
RE: wrong maximums (solved)
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Wed Aug 14 2019 02:42:33 GMT+0200 (Central European Summer Time); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder movesM667 S1 ; Select CoreXY mode
; Network
M550 P"Tronxy X5S" ; Set machine name
secret
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S1 ; Physical drive 0 goes forwards
M569 P1 S1 ; Physical drive 1 goes forwards
M569 P2 S0 ; Physical drive 2 goes backwards
M569 P3 S0 ; Physical drive 3 goes backwards
M569 P4 S0 ; Physical drive 4 goes backwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E95 ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z300.00 E1500.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E5000.00 ; Set accelerations (mm/s^2)
M906 X950.00 Y800.00 Z800.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z400 S0 ; Set axis maxima; Endstops
M574 X1 Y1 S0 ; Set active low and disabled endstops; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H1 F120 T6000 ; Set Z probe type to bltouch and the dive height + speeds
M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:300 Y15:300 S30 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0 I0 F500 H T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
M584 X0 Y1 Z2:4 ; two Z motors connected to driver outputs Z and E1
M671 X0:220 Y0:0 S0.5 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
M208 X0:205 Y0:200 ; X carriage moves from 0 to 300, Y bed goes from 0 to 300; Custom settings are not configured
-
RE: Wrong size (solved)
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z400 S0 ; Set axis maxima -
Wrong size (solved)
Tried printing a 200x210mm size print and the printer cut off corners
have my Tronxy X5s set to 300X x 300Y but when i ask it to go to 300 x 300 it only goes to X205 and Y200.. if i ask it to go further... it wont do it..
i tried looking in the files for 205 and 200 values but cant find anything.. and can find the max set to 300 x 300 x 400 like it should be...
anyone have a explanation and a solution?
-
wrong maximums (solved)
Tried printing a 200x210mm size print and the printer cut off corners
have my Tronxy X5s set to 300X x 300Y but when i ask it to go to 300 x 300 it only goes to X205 and Y200.. if i ask it to go further... it wont do it..
i tried looking in the files for 205 and 200 values but cant find anything.. and can find the max set to 300 x 300 x 400 like it should be...
anyone have a explanation and a solution?
-
RE: Almost giving up on Tronxy X5s
@dc42 has 2 z motors connected to z0 (z1 is jumpered out) and E1,
e0 is extruder motor
and a X and Y motor.. so 5 in total.. and yes i would love that to work but now it seems to rely on the z switch instead of the bltouchand there is one z switch
-
RE: Almost giving up on Tronxy X5s
Thats about the X5, not the X5s
here is a photo https://photos.app.goo.gl/Qo1EbMma8DXWTViD6