@Phaedrux The 15 amp fuse on the Duet between VIN and BED terminals.
I get an error message that says that the temp sensor is unknown. The thermistor is plugged into the pin right next to the BED terminal.
I will try to get a picture up tomorrow.
Thanks again for the help and encouragement!
Here is my current Config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 12 2021 15:48:42 GMT-0800 (PST)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BigPrinter" ; set printer name
; Network
M552 S2 ; enable access point
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X128 Y128 Z128 E16 I0 ; configure microstepping without interpolation
M92 X640.00 Y640.00 Z3200.00 E100.00 ; set steps per mm
M566 X500.00 Y500.00 Z6.00 E60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z1200.00 E3000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X855 Y855 Z855 E855 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; set X limit switch
M574 Y1 S1 P"ystop" ; set Y limit switch
M574 Z1 S1 P"zstop" ; set Z limit switch
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X25:250 Y25:250 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor T100000 B3888 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedtemp" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B3988 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"fan0" Q25000 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
Oh - one more dumb thing. When I upgraded from 3.0 to 3.2 the endstops disappeared from the webcontrol. They work, but I can't see their state under system/machine specific like I could in 3.0. Did I do something dumb?
Thanks - I actually figured it out by sending you all this stuff! I really appreciate your help.
Okay - on to next problem. Thermistors. Bed thermistor isn't registering. It is exactly the same as my hot end. Any ideas?
Last thing - I blew two bed fuses. I have the black wire closest to VIN and red furthest on the Bed. Is it possible that is backwards?
Thanks again for helping dumb me out! I do public policy for a living - learning electronics is my effort at brain expanding. This one has been a hoot!
Oh - and thanks so much for any help! You can see I already fixed the S0 to S1.
Also - the APS is set high to accommodate the larger bed.
NEMA 17 steppers
FLSUN Metal setup used to use an MKS which worked okay
I can move the motors all fine and they go in the right direction
I was able to get the thermistors to read the right values with the same setting but now they all say 2000 and the bed isn't showing up. When they worked the hot end worked fine as did the extruder I have provisioned (it has two - Bowden tube into cyclops - plan to set up later and with inductive bed leveling). However, the bed fuse blew as soon as I sent power.
Now the bed doesn't show up at all - maybe I need to replace the fuse? But I am using a Duet2 on my workbee cnc and it shows all the end stops and doesn't seem to care that there isn't a fuse in the bed.
M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: M308 command is not supported
Warning: M950 command is not supported
Warning: M308 command is not supported
Warning: M950 command is not supported
Warning: M950 command is not supported
Entire Config G
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 12 2021 15:48:42 GMT-0800 (PST)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BigPrinter" ; set printer name
; Network
M552 S2 ; enable access point
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X128 Y128 Z128 E16 I0 ; configure microstepping without interpolation
M92 X640.00 Y640.00 Z3200.00 E100.00 ; set steps per mm
M566 X500.00 Y500.00 Z6.00 E60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z1200.00 E3000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X855 Y855 Z855 E855 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"!xstop" ; set X limit switch
M574 Y1 S1 P"!ystop" ; set Y limit switch
M574 Z1 S1 P"!zstop" ; set Z limit switch
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X25:250 Y25:250 S20 ; define mesh grid
; Heaters
M308 S0 P"bedheat" Y"thermistor T100000 B3988 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"ext1" Y"thermistor" T100000 B3988 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"ext1" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M950 F0 C"fan0" Q25000 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MSD-6J1F4-3SD6N-9TDYN
Used output buffers: 1 of 20 (7 max)
=== RTOS ===
Static ram: 28380
Dynamic ram: 95672 of which 0 recycled
Exception stack ram used: 276
Never used ram: 6744
Task NETWORK ready, free stack 532
Task HEAT blocked, free stack 1256
Task MAIN running, free stack 3568
=== Platform ===
Last reset 00:00:36 ago, cause: power up
Last software reset at 2021-01-12 17:19, reason: User, spinning module GCodes, available RAM 6664 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 21.8, current 25.3, max 25.5
Supply voltage: min 14.7, current 14.8, max 14.9, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-13 15:31:21
Slowest loop: 17.58ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is ready with "m122" in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 17.70ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
The amber lights are working and turn off when the switch is closed. I have tried both active high and active low. The Endstops state is not showing in the webcontrol. Using Reprap 3.2 and the latest version of webcontrol. Also Bed temp not showing up and thermistors registering wrong values (shows 2000 degrees on hotend).
here is my config.g section
; Endstops
M574 X1 S0 P"!xstop" ; configure active-high endstop for low end on X via pin !xstop
M574 Y1 S0 P"!ystop" ; configure active-high endstop for low end on Y via pin !ystop
M574 Z1 S0 P"!zstop" ; configure active-high endstop for low end on Z via pin !zstop