Posts made by Lameran

Thanks for the reply, i measure the Molex Crimps outside of the connector before the Molex in and there were fine, i had no clue how to meassure inside the connector.

Hi there,
i installed an smart effector to my Duet in an Anycubic Predator with Magballs.
I have issues with my Hotend Cooler, its way too slow to cool it.
I meassure the Voltage all the way from the Duet to the cabel and the Molex Connector which goes in the Smart Effector and had 24 V there.
But At the Molex Connector for the Fan itself i meassure 15V. So i m stuck, what could be done to solve this except of connect the Hotend Fan directly?

facepalm feels like an idiot, doesn`t see that. Redefine the offset in G31 and everythings fine now. Thanks!

config.g

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sat Jun 30 2018 19:52:00 GMT+0200

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare

M667 S1 ; Select CoreXY mode

; Network
M550 PHEVO ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z800 E2673 ; Set steps per mm
M566 X1000 Y1000 Z1000 E240 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z250 E40 ; Set maximum speeds (mm/min)
M201 X800 Y800 Z250 E1000 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X280 Y280 Z250 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 S1 ; Set active high endstops

; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P8 I1 R0.4 Z1 F300 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X140 Y140 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 X20:280 Y20:280 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M307 H1 A469.9 C164.2 D9.6 B0

; Fans
M106 P0 S1 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured
M106 P1 S0
M572 D0 S0.08 ;Pressure Advance

bed.g
; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool on Sat Jun 30 2018 19:52:00 GMT+0200
M561 ; clear any bed transform
; Probe the bed at 4 points
G30 P0 X40 Y40 H0 Z-99999
G30 P1 X40 Y140 H0 Z-99999
G30 P2 X40 Y270 H0 Z-99999
G30 P3 X140 Y270 H0 Z-99999
G30 P4 X270 Y270 H0 Z-99999
G30 P5 X270 Y140 H0 Z-99999
G30 P6 X270 Y40 H0 Z-99999 S0

@dc42 No, even after the new Installation of the Firmware isn't there a deployprobe.g or an retractprobe.g

Tried it again, Setup Firmware again, Homeall works like a charm. Start G32, first start point should is defined in bed.g as X40 Y40 but he tried to move to X-90 Y-90? What am i doing wrong?

I run the FW 1.21 a couple of weeks, two weeks ago i changed from IR Probe to Orion. I first thought i made a mistake at my config.g yesterday, so i build a new one today. As this didn`t worked i made the FW Update to exclude an Firmware Issue.

Then i thought something on the Board is broken but G30, homeall and homez worked as they should.

Dont shure if this also is a part of the problem, but my last 3 Thermistor and Thermistor Cables made Heater Faults if the cable is moved in the wrong way...

No the error started at FW 1.21 and i did an upgrade to exclude an FW error. also G30, Homez and homeall did work but G32 and G29 doesnt do whats in bed.g or in M557

No, i had the problem since yesterday and didnt use a BL-Touch. I had an Orion and before an IR Probe. Just updated today from 1.21 to 2.0 and made the config complete new but both changed nothing. There aren`t deployprobe.g or an retractprobe.g in my sys.

My G32 and my G29 doesn`t work anymore. Homeall works fine and in the directions i had defined. But if i send an G32 to the Duet my Hotend crashes against the front left motor mount.

I tried this with FW 1.21 and with FW2.0 Set up the config complete new today and define also Minimum Axis to X/Y 20/20 and tried to define the bed.g at X40 Y270 at first point even then it rushes against the motor mount.

I don`t had a clue anymore what to do exept of throw my Core XY out of the window

DonT know which file was the one with the problem, i deleted the gcode (yes this folder was on the sd too) and the gcodes folder cause i couldnt see any gcodes files at my PC and created a new gcodes folder. Uploaded some gcodes and got no issues anymore.

Hi there,
thanks letting me join the community. I m very impressed of the DuetWifi, but i gotta lots of problems with the WIFI connection.
Long story short, after the update to firmware 1.20 it is much more stable than before no more AJAX Errors and holy shit i could watch the print process the hole print long without pressing the reload page or connect button again. But somethings is wrong with my files page. Everytime i open it up the cursor switch to a load button in the file section and then i gotta get this error. Uploading is only possible if i press the upload file button before the error, than the gcode gets in the main file section. It is not possible to start a print via Laptop or PC but, and this is the strangest part i think with a smartphone i could choose a gcode to print.

Thinking about to try it with a different MicroSD, but was not sure if this is the clue or what to do else.

I checked the Network FAQ. I got a WiFI extender 50 cm away from the Duet, it is on Channel 10 and the Router is 3m far away. Tryed different browsers even (Firefox, IE, Opera), changed nothing