@wilriker
tested without paneldue and print ok in several print part and in 5-6days trial
connect the paneldue again and it random change tool again
i used blv project for the printer. and looks like the led cable is cross with paneldue cable event i already used shielded cable and ferit.
now i forced to select tool 0 and cannot change to another
next try is separate and reroute the cable of the led at the front cover. and get messsage if the system change the tool accidently.
@wilriker said in error:attempting to extrude with no tool selected while printing:
put differ
oops sorry.. i got your poin now. so the first try i must do is disactivate the paneldue and print without paneldue and check if this problem still happen or not. will try in a week of printing. will update as soon as got the problem occurs
the last step i forcely select the tool again when tfree macro called.
but i know it is not solving problem. it is just for emergency.
also measured with my multimeter the resistant of the cable is 0.1
@wilriker said in error:attempting to extrude with no tool selected while printing:
feel they changed along the course of this thread
hello, the main problem is just it is randomly changed from active tool to standby while printing. when it not printing this will not happened at all
before i post last night, i change a lot. change paneldue to 3.2 but it is beta when i try. and i change it back to the old firmware cause new paneldue firmware fit for rrf3.2 also
i also change the baudrate from 115200 to 57600, looks like the problem still exist but not often like before
i also change the cable. from 1m ribbon cable to connect mainboard to paneldue. i changed with stp cable. it is for LAN cable. i just found this cable and test it with 50cm long. the sympthom looks like more rarely show up
but a weeks ago, i print 8 hours long. not a really long printing object. but it can show 5 times. the last make me desperate cause i do not know the notification and the print failed.
@wilriker emm if i do not use serial how paneldue connected? looks like it happend with the lcd connected
my panel have screen guard before, now i remove it and the problem still show up yesterday. sorry for my long journey about this. sometimes it's not happened but lately it happened and make frustrated
@Phaedrux the problem still show up. at lately it more often. i have change the cable to STP lan cable used 4 cable only. i also make it shorter the cable is 50cm long only, before is 1.5m a weeks ago my problem is not occurs often. very rare but sometimes happened but this week it show more often.
is there any trigger event that when it change from active to standby i can forced it back to active?
any way to do it?
@dc42 any help about this. i have disperate to solve it with cabling 
@Phaedrux could you recomend what length which best for the paneldue cable?
@wilriker noted... the real problem is random change of heater extruder from active to standby. and there is no confirmation or anything. that cause my printing is failure.
thanks a lot for your explanation. i describe all the weird behavior that might can help someone notice my real problem
thanks, so the bad command is nothing to do with my real problem
looking another reaso, fighting ha ha ha
@dc42 said in Error: attempting to extrude with no tool selected:
must be no more than 0.1 ohms per conductor
hello, sorry for asking. i am not electronic guy so i alittle bit blank with 0.1ohms per conductor. what this means
i check i use stp lan cable to do it and i check in the internet it is have resistence about 150ohms i cannot use this cable?
@Phaedrux check with M98 P"config.g" in the console there is no error found.
paneldue first boot no error found. but if i tap the stop button, bad command always show up. the number of bad command is random.
this one not resolved, it might one of the sympthoms why my attempting extruder no tool happened.
frustrated....
@theshabobo hello, sorry for asking directly
did you solved it? i also have this problem, i change to stp lan cable and this problem still happened.
any tips ?
@Phaedrux hello, after change the cable the problem show up today.
suddenly it said no tools selected. i change the cable to STP LAN cable.
there is no body around to taps the screen either
btw this problem exist when i upgrade to wdc 3.x
with 2.0 there is no problem like this.
any option what i must check?
sorry for my late reply, lately i change my cable route. i take it away from motor cable and fan. but i did not changing the cable. this morning i got random change tool once again.
this night i already changed the cable. hope this problem really dissapeared
i will update it after several days
@Phaedrux for the error zprobe.in is not free found the problem
i declared with m558 and then i also declared with m574 so i removed the m574. error in dwc is disappeared. trying bltouch still ok. so it must be the problem. thanks about this
bad command just in paneldue. it is random bad command code. i have video about it. how to send video to this forum?
must linked to youtube?
@Phaedrux i am waiting for cable to deliver, still in shipping.
i still not found why zprobe.in is not free. i change all my remark with "; " added space if there is no space after ;
still got random error bad comment in panel due also. but the bad command number always changing.
i use paneldue firmware 1.24 with nologo version
i also flashed it once again and the problem still there. reset it and nothing changes
btw the error Error: Pin 'zprobe.in' is not free is still exist when m98 P"config.g" send in console. i really do not get it why the error still there. the bltouch working properly
@Phaedrux
i already change and added space after ;
but the ; is comment symbol right?
the error changing 04 to 202 to 240 and keep changing... so i really confused what cause of this
tpre, tpost, tfree is generated by generator only. i do not change at all. cause i just have 1 extruder
the cable near z stepper but i already move it to not near any stepper, enmdstop cable or fan wires. the option i still not try is use shielded cable. i bought shield cable online so it might took 2-4 days to deliver
any other option i can check?
this is for M122
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID:
Used output buffers: 5 of 24 (18 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94140 of which 236 recycled
Exception stack ram used: 304
Never used ram: 8412
Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1816) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:05:34 ago, cause: software
Last software reset at 2020-10-15 13:18, reason: User, spinning module GCodes, available RAM 8308 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 35.1, current 35.4, max 36.2
Supply voltage: min 23.7, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-10-15 13:23:40
Cache data hit count 540770322
Slowest loop: 11.78ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.1ms, write time 2.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 41.38ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
@Phaedrux this is for homeall
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Oct 02 2020 12:18:14 GMT+0700 (Indochina Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-355 Y355 F6000 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-355 ; home X axis
G1 H1 Y355 ; home Y axis
G1 X5 Y-5 F6000 ; go back a few mm
G1 H1 X-355 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y355 ; then move slowly to Y axis endstop
;G1 H1 Z-355 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G1 X205 Y164 F6000 ; go to first bed probe point and home Z
;G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
G30
this is for homez
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Oct 02 2020 12:18:14 GMT+0700 (Indochina Time)
G91 ; relative positioning
G1 H2 Z8 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X205 Y164 F6000 ; go to first probe point
G30 ; home Z by probing the bed
this is for config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Oct 02 2020 12:18:13 GMT+0700 (Indochina Time)
; General preferences
M80 ; Turns on the ATX power supply
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BLV mgn Cube" ; set printer name
M669 K1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M569 P4 S0 ; physical drive 4 goes backwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
;M671 X-50:378 Y164:164 S0.5 ; Define the X and Y coordinates of the leadscrews.
M671 X379:-51 Y164:164 S5 ; Define the X and Y coordinates of the leadscrews.
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
;M92 X200.00 Y200.00 Z400.00 E418.00 ; set steps per mm
M92 X198.65 Y200.5 Z399.60 E417.71 ; set steps per mm
M566 X660.00 Y660.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X20000.00 Y20000.00 Z600.00 E2000.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X1700 Y1700 Z1600 E300 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Pressure advance
M572 D0 S0.13 ; enabled Pressure advance
; Axis Limits
;M208 X0 Y0 Z0 S1 ; set axis minima
;M208 X350 Y350 Z350 S0 ; set axis maxima
M208 X-7:343 Y0:340 Z0:450
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
; Filament sensor
;M591 D0 P1 C3 S1 ; Set Filament sensor Simple type (High) for extruder drive 0, connected to endstop input 3 (E0)
;disabled port
;M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.
; Z-Probe
M558 P9 C"^zprobe.in" H5 F200 T4000 X0 Y0 Z0 A2 R0.1 S0.02 ; set Z probe type to bltouch and the dive height + speeds H=Dive Height. F=Speed the bed moves
M574 Z1 S1 P"zprobe.in" ; Set endstops controlled by probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
G31 P25 X-41 Y0 Z2.11 ;sblumnya 2.88 ; set Z probe trigger value, offset and trigger height
M557 X20:308 Y20:308 S92 ; define mesh grid
; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 C0 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950 C0 R4700 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S260 ; set temperature limit for heater 1 to 260C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
;PID set values
M307 H1 A511.8 C182.7 D9.7 V23.8 B0 ; Set PID for hotend values
M307 H0 A126.6 C968.3 D0.6 v23.8 B0 ; Set PID for heated bed values
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 C"Part" ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T35 C"Hotend" ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" ; create fan 2 on pin fan1 and set its frequency
M106 P2 S0 H-1 C"LED" ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
;M564 H0 ; Let the Jog buttons work blv: added to allow jog buttons
M593 F90.5 ; cancel ringing at 40.5Hz
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
;filament sensor setting
M591 D0 P7 C"e0_stop" L6.2 R50:200 E12.4 S1 ; s1 enable s0 disable
;M591 D0 P7 C"e0_stop" R50:200 L6.2 E18.6 S0
T0 ; select first tool
@Phaedrux said in error:attempting to extrude with no tool selected while printing:
22 to be able to fix that on
[0_1602737785250_download.zip](Uploading 100%)
here is my config file and home macro.
would you mind to check mine?